Lines Matching refs:dev_err
373 dev_err(imx290->dev, "I2C read failed for addr: %x\n", addr); in imx290_read_reg()
388 dev_err(imx290->dev, "I2C write failed for addr: %x\n", addr); in imx290_write_reg()
422 dev_err(imx290->dev, "Error setting hold register\n"); in imx290_write_buffered_reg()
430 dev_err(imx290->dev, "Error writing buffered registers\n"); in imx290_write_buffered_reg()
437 dev_err(imx290->dev, "Error setting hold register\n"); in imx290_write_buffered_reg()
450 dev_err(imx290->dev, "Unable to write gain\n"); in imx290_set_gain()
672 dev_err(imx290->dev, "Could not set format registers\n"); in imx290_write_current_format()
681 dev_err(imx290->dev, "Could not set format registers\n"); in imx290_write_current_format()
686 dev_err(imx290->dev, "Unknown pixel format\n"); in imx290_write_current_format()
699 dev_err(imx290->dev, "Error setting HMAX register\n"); in imx290_set_hmax()
705 dev_err(imx290->dev, "Error setting HMAX register\n"); in imx290_set_hmax()
722 dev_err(imx290->dev, "Could not set init registers\n"); in imx290_start_streaming()
729 dev_err(imx290->dev, "Could not set frame format\n"); in imx290_start_streaming()
737 dev_err(imx290->dev, "Could not set current mode\n"); in imx290_start_streaming()
747 dev_err(imx290->dev, "Could not sync v4l2 controls\n"); in imx290_start_streaming()
773 dev_err(imx290->dev, "Start stream failed\n"); in imx290_set_stream()
816 dev_err(imx290->dev, "Lane configuration not supported\n"); in imx290_set_data_lanes()
823 dev_err(imx290->dev, "Error setting Physical Lane number register\n"); in imx290_set_data_lanes()
829 dev_err(imx290->dev, "Error setting CSI Lane mode register\n"); in imx290_set_data_lanes()
835 dev_err(imx290->dev, "Error setting FR/FDG SEL register\n"); in imx290_set_data_lanes()
849 dev_err(dev, "Failed to enable clock\n"); in imx290_power_on()
855 dev_err(dev, "Failed to enable regulators\n"); in imx290_power_on()
949 dev_err(dev, "Unable to initialize I2C\n"); in imx290_probe()
955 dev_err(dev, "Endpoint node not found\n"); in imx290_probe()
962 dev_err(dev, "Unsupported bus type, should be CSI2\n"); in imx290_probe()
965 dev_err(dev, "Parsing endpoint node failed\n"); in imx290_probe()
972 dev_err(dev, "Invalid data lanes: %d\n", imx290->nlanes); in imx290_probe()
980 dev_err(dev, "link-frequency property not found in DT\n"); in imx290_probe()
988 dev_err(dev, "Link frequency of %lld is not supported\n", fq); in imx290_probe()
996 dev_err(dev, "Could not get xclk"); in imx290_probe()
1004 dev_err(dev, "Could not get xclk frequency\n"); in imx290_probe()
1010 dev_err(dev, "External clock frequency %u is not supported\n", in imx290_probe()
1018 dev_err(dev, "Could not set xclk frequency\n"); in imx290_probe()
1024 dev_err(dev, "Cannot get regulators\n"); in imx290_probe()
1031 dev_err(dev, "Cannot get reset gpio\n"); in imx290_probe()
1071 dev_err(dev, "Control initialization error %d\n", in imx290_probe()
1086 dev_err(dev, "Could not register media entity\n"); in imx290_probe()
1092 dev_err(dev, "Could not register v4l2 device\n"); in imx290_probe()
1099 dev_err(dev, "Could not power on the device\n"); in imx290_probe()