Lines Matching refs:e_dbg
385 e_dbg("Disabling MWI on 82542 rev 2.0\n"); in e1000_reset_hw()
390 e_dbg("Masking off all interrupts\n"); in e1000_reset_hw()
423 e_dbg("Issuing a global reset to MAC\n"); in e1000_reset_hw()
499 e_dbg("Masking off all interrupts\n"); in e1000_reset_hw()
535 e_dbg("Error Initializing Identification LED\n"); in e1000_init_hw()
543 e_dbg("Initializing the IEEE VLAN\n"); in e1000_init_hw()
550 e_dbg("Disabling MWI on 82542 rev 2.0\n"); in e1000_init_hw()
572 e_dbg("Zeroing the MTA\n"); in e1000_init_hw()
703 e_dbg("EEPROM Read Error\n"); in e1000_setup_link()
727 e_dbg("After fix-ups FlowControl is now = %x\n", hw->fc); in e1000_setup_link()
740 e_dbg("EEPROM Read Error\n"); in e1000_setup_link()
757 e_dbg("Initializing the Flow Control address, type and timer regs\n"); in e1000_setup_link()
875 e_dbg("Flow control param set incorrectly\n"); in e1000_setup_fiber_serdes_link()
885 e_dbg("Auto-negotiation enabled\n"); in e1000_setup_fiber_serdes_link()
903 e_dbg("Looking for Link\n"); in e1000_setup_fiber_serdes_link()
911 e_dbg("Never got a valid link from auto-neg!!!\n"); in e1000_setup_fiber_serdes_link()
920 e_dbg("Error while checking for link\n"); in e1000_setup_fiber_serdes_link()
926 e_dbg("Valid Link Found\n"); in e1000_setup_fiber_serdes_link()
929 e_dbg("No Signal Detected\n"); in e1000_setup_fiber_serdes_link()
947 e_dbg("Error Resetting the PHY\n"); in e1000_copper_link_rtl_setup()
963 e_dbg("e1000_copper_link_rtl_setup failed!\n"); in gbe_dhg_phy_setup()
983 e_dbg("e1000_copper_link_rtl_setup failed!\n"); in gbe_dhg_phy_setup()
988 e_dbg("Error Resetting the PHY\n"); in gbe_dhg_phy_setup()
1028 e_dbg("Error, did not detect valid phy.\n"); in e1000_copper_link_preconfig()
1031 e_dbg("Phy ID = %x\n", hw->phy_id); in e1000_copper_link_preconfig()
1071 e_dbg("Error Resetting the PHY\n"); in e1000_copper_link_igp_setup()
1088 e_dbg("Error Disabling LPLU D3\n"); in e1000_copper_link_igp_setup()
1294 e_dbg("Error Resetting the PHY\n"); in e1000_copper_link_mgp_setup()
1328 e_dbg("Reconfiguring auto-neg advertisement params\n"); in e1000_copper_link_autoneg()
1331 e_dbg("Error Setting up Auto-Negotiation\n"); in e1000_copper_link_autoneg()
1334 e_dbg("Restarting Auto-Neg\n"); in e1000_copper_link_autoneg()
1354 e_dbg in e1000_copper_link_autoneg()
1387 e_dbg("Error configuring MAC to PHY settings\n"); in e1000_copper_link_postconfig()
1393 e_dbg("Error Configuring Flow Control\n"); in e1000_copper_link_postconfig()
1401 e_dbg("Error Configuring DSP after link up\n"); in e1000_copper_link_postconfig()
1437 e_dbg("gbe_dhg_phy_setup failed!\n"); in e1000_setup_copper_link()
1453 e_dbg("Forcing speed and duplex\n"); in e1000_setup_copper_link()
1456 e_dbg("Error Forcing Speed and Duplex\n"); in e1000_setup_copper_link()
1478 e_dbg("Valid link established!!!\n"); in e1000_setup_copper_link()
1484 e_dbg("Unable to establish link!!!\n"); in e1000_setup_copper_link()
1526 e_dbg("autoneg_advertised %x\n", hw->autoneg_advertised); in e1000_phy_setup_autoneg()
1530 e_dbg("Advertise 10mb Half duplex\n"); in e1000_phy_setup_autoneg()
1536 e_dbg("Advertise 10mb Full duplex\n"); in e1000_phy_setup_autoneg()
1542 e_dbg("Advertise 100mb Half duplex\n"); in e1000_phy_setup_autoneg()
1548 e_dbg("Advertise 100mb Full duplex\n"); in e1000_phy_setup_autoneg()
1554 e_dbg in e1000_phy_setup_autoneg()
1560 e_dbg("Advertise 1000mb Full duplex\n"); in e1000_phy_setup_autoneg()
1614 e_dbg("Flow control param set incorrectly\n"); in e1000_phy_setup_autoneg()
1622 e_dbg("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg); in e1000_phy_setup_autoneg()
1654 e_dbg("hw->fc = %d\n", hw->fc); in e1000_phy_force_speed_duplex()
1683 e_dbg("Full Duplex\n"); in e1000_phy_force_speed_duplex()
1690 e_dbg("Half Duplex\n"); in e1000_phy_force_speed_duplex()
1700 e_dbg("Forcing 100mb "); in e1000_phy_force_speed_duplex()
1706 e_dbg("Forcing 10mb "); in e1000_phy_force_speed_duplex()
1729 e_dbg("M88E1000 PSCR: %x\n", phy_data); in e1000_phy_force_speed_duplex()
1769 e_dbg("Waiting for forced speed/duplex link.\n"); in e1000_phy_force_speed_duplex()
1797 e_dbg("Error Resetting PHY DSP\n"); in e1000_phy_force_speed_duplex()
2024 e_dbg("Flow control param set incorrectly\n"); in e1000_force_mac_fc()
2068 e_dbg("Error forcing flow control settings\n"); in e1000_config_fc_after_link_up()
2152 e_dbg("Flow Control = FULL.\n"); in e1000_config_fc_after_link_up()
2155 e_dbg in e1000_config_fc_after_link_up()
2172 e_dbg in e1000_config_fc_after_link_up()
2188 e_dbg in e1000_config_fc_after_link_up()
2217 e_dbg("Flow Control = NONE.\n"); in e1000_config_fc_after_link_up()
2220 e_dbg in e1000_config_fc_after_link_up()
2231 e_dbg in e1000_config_fc_after_link_up()
2244 e_dbg in e1000_config_fc_after_link_up()
2249 e_dbg in e1000_config_fc_after_link_up()
2286 e_dbg("NOT RXing /C/, disable AutoNeg and force link.\n"); in e1000_check_for_serdes_link_generic()
2299 e_dbg("Error configuring flow control\n"); in e1000_check_for_serdes_link_generic()
2308 e_dbg("RXing /C/, enable AutoNeg and stop forcing link.\n"); in e1000_check_for_serdes_link_generic()
2324 e_dbg("SERDES: Link up - forced.\n"); in e1000_check_for_serdes_link_generic()
2328 e_dbg("SERDES: Link down - force failed.\n"); in e1000_check_for_serdes_link_generic()
2341 e_dbg("SERDES: Link up - autoneg " in e1000_check_for_serdes_link_generic()
2345 e_dbg("SERDES: Link down - invalid" in e1000_check_for_serdes_link_generic()
2350 e_dbg("SERDES: Link down - no sync.\n"); in e1000_check_for_serdes_link_generic()
2354 e_dbg("SERDES: Link down - autoneg failed\n"); in e1000_check_for_serdes_link_generic()
2471 e_dbg in e1000_check_for_link()
2484 e_dbg("Error configuring flow control\n"); in e1000_check_for_link()
2503 e_dbg in e1000_check_for_link()
2562 e_dbg("1000 Mbs, "); in e1000_get_speed_and_duplex()
2565 e_dbg("100 Mbs, "); in e1000_get_speed_and_duplex()
2568 e_dbg("10 Mbs, "); in e1000_get_speed_and_duplex()
2573 e_dbg("Full Duplex\n"); in e1000_get_speed_and_duplex()
2576 e_dbg(" Half Duplex\n"); in e1000_get_speed_and_duplex()
2579 e_dbg("1000 Mbs, Full Duplex\n"); in e1000_get_speed_and_duplex()
2623 e_dbg("Waiting for Auto-Neg to complete.\n"); in e1000_wait_autoneg()
2815 e_dbg("PHY Address %d is out of range\n", reg_addr); in e1000_read_phy_reg_ex()
2843 e_dbg("MDI Read did not complete\n"); in e1000_read_phy_reg_ex()
2849 e_dbg("MDI Read Error\n"); in e1000_read_phy_reg_ex()
2870 e_dbg("MDI Read did not complete\n"); in e1000_read_phy_reg_ex()
2874 e_dbg("MDI Error\n"); in e1000_read_phy_reg_ex()
2953 e_dbg("PHY Address %d is out of range\n", reg_addr); in e1000_write_phy_reg_ex()
2982 e_dbg("MDI Write did not complete\n"); in e1000_write_phy_reg_ex()
3003 e_dbg("MDI Write did not complete\n"); in e1000_write_phy_reg_ex()
3043 e_dbg("Resetting Phy...\n"); in e1000_phy_hw_reset()
3187 e_dbg("Invalid MAC type %d\n", hw->mac_type); in e1000_detect_gig_phy()
3193 e_dbg("PHY ID 0x%X detected\n", hw->phy_id); in e1000_detect_gig_phy()
3196 e_dbg("Invalid PHY ID 0x%X\n", hw->phy_id); in e1000_detect_gig_phy()
3399 e_dbg("PHY info is only valid for copper media\n"); in e1000_phy_get_info()
3412 e_dbg("PHY info is only valid if link is up\n"); in e1000_phy_get_info()
3428 e_dbg("Invalid MDI setting detected\n"); in e1000_validate_mdi_setting()
3682 e_dbg("Could not acquire EEPROM grant\n"); in e1000_acquire_eeprom()
3835 e_dbg("SPI EEPROM Status error\n"); in e1000_spi_eeprom_ready()
3877 e_dbg("\"words\" parameter out of bounds. Words = %d," in e1000_do_read_eeprom()
3965 e_dbg("EEPROM Read Error\n"); in e1000_validate_eeprom_checksum()
3980 e_dbg("EEPROM Checksum Invalid\n"); in e1000_validate_eeprom_checksum()
3999 e_dbg("EEPROM Read Error\n"); in e1000_update_eeprom_checksum()
4006 e_dbg("EEPROM Write Error\n"); in e1000_update_eeprom_checksum()
4050 e_dbg("\"words\" parameter out of bounds\n"); in e1000_do_write_eeprom()
4195 e_dbg("EEPROM Write did not complete\n"); in e1000_write_eeprom_microwire()
4235 e_dbg("EEPROM Read Error\n"); in e1000_read_mac_addr()
4271 e_dbg("Programming MAC Address into RAR[0]\n"); in e1000_init_rx_addrs()
4280 e_dbg("Clearing RAR[1-14]\n"); in e1000_init_rx_addrs()
4432 e_dbg("EEPROM Read Error\n"); in e1000_id_led_init()
4756 e_dbg("Not in Adaptive IFS mode!\n"); in e1000_reset_adaptive()
4792 e_dbg("Not in Adaptive IFS mode!\n"); in e1000_update_adaptive()
5177 e_dbg("Error getting link speed and duplex\n"); in e1000_config_dsp_after_link_change()