Lines Matching refs:LOGNAME
61 # define LOGNAME "msnd_classic" macro
65 # define LOGNAME "snd_msnd_pinnacle" macro
124 snd_printd(KERN_WARNING LOGNAME ": Play underflow %i\n", in snd_msnd_eval_dsp_msg()
131 snd_printd(KERN_WARNING LOGNAME ": Record overflow\n"); in snd_msnd_eval_dsp_msg()
136 snd_printd(KERN_WARNING LOGNAME in snd_msnd_eval_dsp_msg()
149 snd_printd(KERN_WARNING LOGNAME ": HIMT message %d 0x%02x\n", in snd_msnd_eval_dsp_msg()
200 snd_printk(KERN_ERR LOGNAME ": Cannot reset DSP\n"); in snd_msnd_reset_dsp()
216 snd_printk(KERN_ERR LOGNAME ": I/O port conflict\n"); in snd_msnd_probe()
228 printk(KERN_INFO LOGNAME ": %s, " in snd_msnd_probe()
288 printk(KERN_INFO LOGNAME ": %s revision %s, Xilinx version %s, " in snd_msnd_probe()
380 printk(KERN_ERR LOGNAME ": Error loading " INITCODEFILE); in upload_dsp_code()
385 printk(KERN_ERR LOGNAME ": Error loading " PERMCODEFILE); in upload_dsp_code()
391 printk(KERN_WARNING LOGNAME ": Error uploading to DSP\n"); in upload_dsp_code()
395 printk(KERN_INFO LOGNAME ": DSP firmware uploaded\n"); in upload_dsp_code()
428 printk(KERN_WARNING LOGNAME ": Cannot initialize SMA\n"); in snd_msnd_initialize()
438 printk(KERN_WARNING LOGNAME ": Cannot upload DSP code\n"); in snd_msnd_initialize()
447 snd_printd(KERN_ERR LOGNAME ": DSP reset timeout\n"); in snd_msnd_initialize()
469 printk(KERN_WARNING LOGNAME ": DSP reset failed\n"); in snd_msnd_dsp_full_reset()
499 printk(KERN_WARNING LOGNAME ": ADC calibration failed\n"); in snd_msnd_calibrate_adc()
530 printk(KERN_ERR LOGNAME ": Couldn't grab IRQ %d\n", chip->irq); in snd_msnd_attach()
540 printk(KERN_ERR LOGNAME in snd_msnd_attach()
547 printk(KERN_ERR LOGNAME in snd_msnd_attach()
559 printk(KERN_ERR LOGNAME ": error creating new PCM device\n"); in snd_msnd_attach()
565 printk(KERN_ERR LOGNAME ": error creating new Mixer device\n"); in snd_msnd_attach()
580 printk(KERN_ERR LOGNAME in snd_msnd_attach()
612 printk(KERN_ERR LOGNAME ": snd_msnd_write_cfg: I/O error\n"); in snd_msnd_write_cfg()
701 printk(KERN_INFO LOGNAME ": Resetting all devices\n"); in snd_msnd_pinnacle_cfg_reset()
782 printk(KERN_WARNING LOGNAME ": io, irq and mem must be set\n"); in snd_msnd_isa_match()
795 printk(KERN_ERR LOGNAME ": \"io\" - DSP I/O base must be set " in snd_msnd_isa_match()
802 printk(KERN_ERR LOGNAME in snd_msnd_isa_match()
815 printk(KERN_ERR LOGNAME in snd_msnd_isa_match()
826 printk(KERN_ERR LOGNAME ": \"mem\" - must be set to " in snd_msnd_isa_match()
834 printk(KERN_INFO LOGNAME ": Assuming PnP mode\n"); in snd_msnd_isa_match()
836 printk(KERN_INFO LOGNAME in snd_msnd_isa_match()
857 printk(KERN_INFO LOGNAME ": Assuming PnP mode\n"); in snd_msnd_isa_probe()
900 printk(KERN_INFO LOGNAME ": Non-PnP mode: configuring at port 0x%lx\n", in snd_msnd_isa_probe()
905 printk(KERN_ERR LOGNAME ": Config port 0x%lx conflict\n", in snd_msnd_isa_probe()
926 printk(KERN_INFO LOGNAME in snd_msnd_isa_probe()
941 printk(KERN_INFO LOGNAME in snd_msnd_isa_probe()
954 printk(KERN_INFO LOGNAME in snd_msnd_isa_probe()
992 printk(KERN_ERR LOGNAME ": Probe failed\n"); in snd_msnd_isa_probe()
998 printk(KERN_ERR LOGNAME ": Attach failed\n"); in snd_msnd_isa_probe()
1101 printk(KERN_ERR LOGNAME ": Probe failed\n"); in snd_msnd_pnp_detect()
1107 printk(KERN_ERR LOGNAME ": Attach failed\n"); in snd_msnd_pnp_detect()