1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3 * USB HOST XHCI Controller
4 *
5 * Based on xHCI host controller driver in linux-kernel
6 * by Sarah Sharp.
7 *
8 * Copyright (C) 2008 Intel Corp.
9 * Author: Sarah Sharp
10 *
11 * Copyright (C) 2013 Samsung Electronics Co.Ltd
12 * Authors: Vivek Gautam <gautam.vivek@samsung.com>
13 * Vikas Sajjan <vikas.sajjan@samsung.com>
14 */
15
16 #ifndef HOST_XHCI_H_
17 #define HOST_XHCI_H_
18
19 #include <phys2bus.h>
20 #include <reset.h>
21 #include <asm/types.h>
22 #include <asm/cache.h>
23 #include <asm/io.h>
24 #include <linux/list.h>
25 #include <linux/compat.h>
26
27 #define MAX_EP_CTX_NUM 31
28 #define XHCI_ALIGNMENT 64
29 /* Generic timeout for XHCI events */
30 #define XHCI_TIMEOUT 5000
31 /* Max number of USB devices for any host controller - limit in section 6.1 */
32 #define MAX_HC_SLOTS 256
33 /* Section 5.3.3 - MaxPorts */
34 #define MAX_HC_PORTS 255
35
36 /* Up to 16 ms to halt an HC */
37 #define XHCI_MAX_HALT_USEC (16*1000)
38
39 #define XHCI_MAX_RESET_USEC (250*1000)
40
41 /*
42 * These bits are Read Only (RO) and should be saved and written to the
43 * registers: 0, 3, 10:13, 30
44 * connect status, over-current status, port speed, and device removable.
45 * connect status and port speed are also sticky - meaning they're in
46 * the AUX well and they aren't changed by a hot, warm, or cold reset.
47 */
48 #define XHCI_PORT_RO ((1 << 0) | (1 << 3) | (0xf << 10) | (1 << 30))
49 /*
50 * These bits are RW; writing a 0 clears the bit, writing a 1 sets the bit:
51 * bits 5:8, 9, 14:15, 25:27
52 * link state, port power, port indicator state, "wake on" enable state
53 */
54 #define XHCI_PORT_RWS ((0xf << 5) | (1 << 9) | (0x3 << 14) | (0x7 << 25))
55 /*
56 * These bits are RW; writing a 1 sets the bit, writing a 0 has no effect:
57 * bit 4 (port reset)
58 */
59 #define XHCI_PORT_RW1S ((1 << 4))
60 /*
61 * These bits are RW; writing a 1 clears the bit, writing a 0 has no effect:
62 * bits 1, 17, 18, 19, 20, 21, 22, 23
63 * port enable/disable, and
64 * change bits: connect, PED,
65 * warm port reset changed (reserved zero for USB 2.0 ports),
66 * over-current, reset, link state, and L1 change
67 */
68 #define XHCI_PORT_RW1CS ((1 << 1) | (0x7f << 17))
69 /*
70 * Bit 16 is RW, and writing a '1' to it causes the link state control to be
71 * latched in
72 */
73 #define XHCI_PORT_RW ((1 << 16))
74 /*
75 * These bits are Reserved Zero (RsvdZ) and zero should be written to them:
76 * bits 2, 24, 28:31
77 */
78 #define XHCI_PORT_RZ ((1 << 2) | (1 << 24) | (0xf << 28))
79
80 /*
81 * XHCI Register Space.
82 */
83 struct xhci_hccr {
84 uint32_t cr_capbase;
85 uint32_t cr_hcsparams1;
86 uint32_t cr_hcsparams2;
87 uint32_t cr_hcsparams3;
88 uint32_t cr_hccparams;
89 uint32_t cr_dboff;
90 uint32_t cr_rtsoff;
91
92 /* hc_capbase bitmasks */
93 /* bits 7:0 - how long is the Capabilities register */
94 #define HC_LENGTH(p) XHCI_HC_LENGTH(p)
95 /* bits 31:16 */
96 #define HC_VERSION(p) (((p) >> 16) & 0xffff)
97
98 /* HCSPARAMS1 - hcs_params1 - bitmasks */
99 /* bits 0:7, Max Device Slots */
100 #define HCS_MAX_SLOTS(p) (((p) >> 0) & 0xff)
101 #define HCS_SLOTS_MASK 0xff
102 /* bits 8:18, Max Interrupters */
103 #define HCS_MAX_INTRS(p) (((p) >> 8) & 0x7ff)
104 /* bits 24:31, Max Ports - max value is 0x7F = 127 ports */
105 #define HCS_MAX_PORTS(p) (((p) >> 24) & 0xff)
106
107 /* HCSPARAMS2 - hcs_params2 - bitmasks */
108 /* bits 0:3, frames or uframes that SW needs to queue transactions
109 * ahead of the HW to meet periodic deadlines */
110 #define HCS_IST(p) (((p) >> 0) & 0xf)
111 /* bits 4:7, max number of Event Ring segments */
112 #define HCS_ERST_MAX(p) (((p) >> 4) & 0xf)
113 /* bits 21:25 Hi 5 bits of Scratchpad buffers SW must allocate for the HW */
114 /* bit 26 Scratchpad restore - for save/restore HW state - not used yet */
115 /* bits 27:31 Lo 5 bits of Scratchpad buffers SW must allocate for the HW */
116 #define HCS_MAX_SCRATCHPAD(p) ((((p) >> 16) & 0x3e0) | (((p) >> 27) & 0x1f))
117
118 /* HCSPARAMS3 - hcs_params3 - bitmasks */
119 /* bits 0:7, Max U1 to U0 latency for the roothub ports */
120 #define HCS_U1_LATENCY(p) (((p) >> 0) & 0xff)
121 /* bits 16:31, Max U2 to U0 latency for the roothub ports */
122 #define HCS_U2_LATENCY(p) (((p) >> 16) & 0xffff)
123
124 /* HCCPARAMS - hcc_params - bitmasks */
125 /* true: HC can use 64-bit address pointers */
126 #define HCC_64BIT_ADDR(p) ((p) & (1 << 0))
127 /* true: HC can do bandwidth negotiation */
128 #define HCC_BANDWIDTH_NEG(p) ((p) & (1 << 1))
129 /* true: HC uses 64-byte Device Context structures
130 * FIXME 64-byte context structures aren't supported yet.
131 */
132 #define HCC_64BYTE_CONTEXT(p) ((p) & (1 << 2))
133 /* true: HC has port power switches */
134 #define HCC_PPC(p) ((p) & (1 << 3))
135 /* true: HC has port indicators */
136 #define HCS_INDICATOR(p) ((p) & (1 << 4))
137 /* true: HC has Light HC Reset Capability */
138 #define HCC_LIGHT_RESET(p) ((p) & (1 << 5))
139 /* true: HC supports latency tolerance messaging */
140 #define HCC_LTC(p) ((p) & (1 << 6))
141 /* true: no secondary Stream ID Support */
142 #define HCC_NSS(p) ((p) & (1 << 7))
143 /* Max size for Primary Stream Arrays - 2^(n+1), where n is bits 12:15 */
144 #define HCC_MAX_PSA(p) (1 << ((((p) >> 12) & 0xf) + 1))
145 /* Extended Capabilities pointer from PCI base - section 5.3.6 */
146 #define HCC_EXT_CAPS(p) XHCI_HCC_EXT_CAPS(p)
147
148 /* db_off bitmask - bits 0:1 reserved */
149 #define DBOFF_MASK (~0x3)
150
151 /* run_regs_off bitmask - bits 0:4 reserved */
152 #define RTSOFF_MASK (~0x1f)
153
154 };
155
156 struct xhci_hcor_port_regs {
157 volatile uint32_t or_portsc;
158 volatile uint32_t or_portpmsc;
159 volatile uint32_t or_portli;
160 volatile uint32_t reserved_3;
161 };
162
163 struct xhci_hcor {
164 volatile uint32_t or_usbcmd;
165 volatile uint32_t or_usbsts;
166 volatile uint32_t or_pagesize;
167 volatile uint32_t reserved_0[2];
168 volatile uint32_t or_dnctrl;
169 volatile uint64_t or_crcr;
170 volatile uint32_t reserved_1[4];
171 volatile uint64_t or_dcbaap;
172 volatile uint32_t or_config;
173 volatile uint32_t reserved_2[241];
174 struct xhci_hcor_port_regs portregs[MAX_HC_PORTS];
175 };
176
177 /* USBCMD - USB command - command bitmasks */
178 /* start/stop HC execution - do not write unless HC is halted*/
179 #define CMD_RUN XHCI_CMD_RUN
180 /* Reset HC - resets internal HC state machine and all registers (except
181 * PCI config regs). HC does NOT drive a USB reset on the downstream ports.
182 * The xHCI driver must reinitialize the xHC after setting this bit.
183 */
184 #define CMD_RESET (1 << 1)
185 /* Event Interrupt Enable - a '1' allows interrupts from the host controller */
186 #define CMD_EIE XHCI_CMD_EIE
187 /* Host System Error Interrupt Enable - get out-of-band signal for HC errors */
188 #define CMD_HSEIE XHCI_CMD_HSEIE
189 /* bits 4:6 are reserved (and should be preserved on writes). */
190 /* light reset (port status stays unchanged) - reset completed when this is 0 */
191 #define CMD_LRESET (1 << 7)
192 /* host controller save/restore state. */
193 #define CMD_CSS (1 << 8)
194 #define CMD_CRS (1 << 9)
195 /* Enable Wrap Event - '1' means xHC generates an event when MFINDEX wraps. */
196 #define CMD_EWE XHCI_CMD_EWE
197 /* MFINDEX power management - '1' means xHC can stop MFINDEX counter if all root
198 * hubs are in U3 (selective suspend), disconnect, disabled, or powered-off.
199 * '0' means the xHC can power it off if all ports are in the disconnect,
200 * disabled, or powered-off state.
201 */
202 #define CMD_PM_INDEX (1 << 11)
203 /* bits 12:31 are reserved (and should be preserved on writes). */
204
205 /* USBSTS - USB status - status bitmasks */
206 /* HC not running - set to 1 when run/stop bit is cleared. */
207 #define STS_HALT XHCI_STS_HALT
208 /* serious error, e.g. PCI parity error. The HC will clear the run/stop bit. */
209 #define STS_FATAL (1 << 2)
210 /* event interrupt - clear this prior to clearing any IP flags in IR set*/
211 #define STS_EINT (1 << 3)
212 /* port change detect */
213 #define STS_PORT (1 << 4)
214 /* bits 5:7 reserved and zeroed */
215 /* save state status - '1' means xHC is saving state */
216 #define STS_SAVE (1 << 8)
217 /* restore state status - '1' means xHC is restoring state */
218 #define STS_RESTORE (1 << 9)
219 /* true: save or restore error */
220 #define STS_SRE (1 << 10)
221 /* true: Controller Not Ready to accept doorbell or op reg writes after reset */
222 #define STS_CNR XHCI_STS_CNR
223 /* true: internal Host Controller Error - SW needs to reset and reinitialize */
224 #define STS_HCE (1 << 12)
225 /* bits 13:31 reserved and should be preserved */
226
227 /*
228 * DNCTRL - Device Notification Control Register - dev_notification bitmasks
229 * Generate a device notification event when the HC sees a transaction with a
230 * notification type that matches a bit set in this bit field.
231 */
232 #define DEV_NOTE_MASK (0xffff)
233 #define ENABLE_DEV_NOTE(x) (1 << (x))
234 /* Most of the device notification types should only be used for debug.
235 * SW does need to pay attention to function wake notifications.
236 */
237 #define DEV_NOTE_FWAKE ENABLE_DEV_NOTE(1)
238
239 /* CRCR - Command Ring Control Register - cmd_ring bitmasks */
240 /* bit 0 is the command ring cycle state */
241 /* stop ring operation after completion of the currently executing command */
242 #define CMD_RING_PAUSE (1 << 1)
243 /* stop ring immediately - abort the currently executing command */
244 #define CMD_RING_ABORT (1 << 2)
245 /* true: command ring is running */
246 #define CMD_RING_RUNNING (1 << 3)
247 /* bits 4:5 reserved and should be preserved */
248 /* Command Ring pointer - bit mask for the lower 32 bits. */
249 #define CMD_RING_RSVD_BITS (0x3f)
250
251 /* CONFIG - Configure Register - config_reg bitmasks */
252 /* bits 0:7 - maximum number of device slots enabled (NumSlotsEn) */
253 #define MAX_DEVS(p) ((p) & 0xff)
254 /* bits 8:31 - reserved and should be preserved */
255
256 /* PORTSC - Port Status and Control Register - port_status_base bitmasks */
257 /* true: device connected */
258 #define PORT_CONNECT (1 << 0)
259 /* true: port enabled */
260 #define PORT_PE (1 << 1)
261 /* bit 2 reserved and zeroed */
262 /* true: port has an over-current condition */
263 #define PORT_OC (1 << 3)
264 /* true: port reset signaling asserted */
265 #define PORT_RESET (1 << 4)
266 /* Port Link State - bits 5:8
267 * A read gives the current link PM state of the port,
268 * a write with Link State Write Strobe set sets the link state.
269 */
270 #define PORT_PLS_MASK (0xf << 5)
271 #define XDEV_U0 (0x0 << 5)
272 #define XDEV_U2 (0x2 << 5)
273 #define XDEV_U3 (0x3 << 5)
274 #define XDEV_RESUME (0xf << 5)
275 /* true: port has power (see HCC_PPC) */
276 #define PORT_POWER (1 << 9)
277 /* bits 10:13 indicate device speed:
278 * 0 - undefined speed - port hasn't be initialized by a reset yet
279 * 1 - full speed
280 * 2 - low speed
281 * 3 - high speed
282 * 4 - super speed
283 * 5-15 reserved
284 */
285 #define DEV_SPEED_MASK (0xf << 10)
286 #define XDEV_FS (0x1 << 10)
287 #define XDEV_LS (0x2 << 10)
288 #define XDEV_HS (0x3 << 10)
289 #define XDEV_SS (0x4 << 10)
290 #define DEV_UNDEFSPEED(p) (((p) & DEV_SPEED_MASK) == (0x0<<10))
291 #define DEV_FULLSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_FS)
292 #define DEV_LOWSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_LS)
293 #define DEV_HIGHSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_HS)
294 #define DEV_SUPERSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_SS)
295 /* Bits 20:23 in the Slot Context are the speed for the device */
296 #define SLOT_SPEED_FS (XDEV_FS << 10)
297 #define SLOT_SPEED_LS (XDEV_LS << 10)
298 #define SLOT_SPEED_HS (XDEV_HS << 10)
299 #define SLOT_SPEED_SS (XDEV_SS << 10)
300 /* Port Indicator Control */
301 #define PORT_LED_OFF (0 << 14)
302 #define PORT_LED_AMBER (1 << 14)
303 #define PORT_LED_GREEN (2 << 14)
304 #define PORT_LED_MASK (3 << 14)
305 /* Port Link State Write Strobe - set this when changing link state */
306 #define PORT_LINK_STROBE (1 << 16)
307 /* true: connect status change */
308 #define PORT_CSC (1 << 17)
309 /* true: port enable change */
310 #define PORT_PEC (1 << 18)
311 /* true: warm reset for a USB 3.0 device is done. A "hot" reset puts the port
312 * into an enabled state, and the device into the default state. A "warm" reset
313 * also resets the link, forcing the device through the link training sequence.
314 * SW can also look at the Port Reset register to see when warm reset is done.
315 */
316 #define PORT_WRC (1 << 19)
317 /* true: over-current change */
318 #define PORT_OCC (1 << 20)
319 /* true: reset change - 1 to 0 transition of PORT_RESET */
320 #define PORT_RC (1 << 21)
321 /* port link status change - set on some port link state transitions:
322 * Transition Reason
323 * --------------------------------------------------------------------------
324 * - U3 to Resume Wakeup signaling from a device
325 * - Resume to Recovery to U0 USB 3.0 device resume
326 * - Resume to U0 USB 2.0 device resume
327 * - U3 to Recovery to U0 Software resume of USB 3.0 device complete
328 * - U3 to U0 Software resume of USB 2.0 device complete
329 * - U2 to U0 L1 resume of USB 2.1 device complete
330 * - U0 to U0 (???) L1 entry rejection by USB 2.1 device
331 * - U0 to disabled L1 entry error with USB 2.1 device
332 * - Any state to inactive Error on USB 3.0 port
333 */
334 #define PORT_PLC (1 << 22)
335 /* port configure error change - port failed to configure its link partner */
336 #define PORT_CEC (1 << 23)
337 /* bit 24 reserved */
338 /* wake on connect (enable) */
339 #define PORT_WKCONN_E (1 << 25)
340 /* wake on disconnect (enable) */
341 #define PORT_WKDISC_E (1 << 26)
342 /* wake on over-current (enable) */
343 #define PORT_WKOC_E (1 << 27)
344 /* bits 28:29 reserved */
345 /* true: device is removable - for USB 3.0 roothub emulation */
346 #define PORT_DEV_REMOVE (1 << 30)
347 /* Initiate a warm port reset - complete when PORT_WRC is '1' */
348 #define PORT_WR (1 << 31)
349
350 /* We mark duplicate entries with -1 */
351 #define DUPLICATE_ENTRY ((u8)(-1))
352
353 /* Port Power Management Status and Control - port_power_base bitmasks */
354 /* Inactivity timer value for transitions into U1, in microseconds.
355 * Timeout can be up to 127us. 0xFF means an infinite timeout.
356 */
357 #define PORT_U1_TIMEOUT(p) ((p) & 0xff)
358 /* Inactivity timer value for transitions into U2 */
359 #define PORT_U2_TIMEOUT(p) (((p) & 0xff) << 8)
360 /* Bits 24:31 for port testing */
361
362 /* USB2 Protocol PORTSPMSC */
363 #define PORT_L1S_MASK 7
364 #define PORT_L1S_SUCCESS 1
365 #define PORT_RWE (1 << 3)
366 #define PORT_HIRD(p) (((p) & 0xf) << 4)
367 #define PORT_HIRD_MASK (0xf << 4)
368 #define PORT_L1DS(p) (((p) & 0xff) << 8)
369 #define PORT_HLE (1 << 16)
370
371 /**
372 * struct xhci_intr_reg - Interrupt Register Set
373 * @irq_pending: IMAN - Interrupt Management Register. Used to enable
374 * interrupts and check for pending interrupts.
375 * @irq_control: IMOD - Interrupt Moderation Register.
376 * Used to throttle interrupts.
377 * @erst_size: Number of segments in the
378 Event Ring Segment Table (ERST).
379 * @erst_base: ERST base address.
380 * @erst_dequeue: Event ring dequeue pointer.
381 *
382 * Each interrupter (defined by a MSI-X vector) has an event ring and an Event
383 * Ring Segment Table (ERST) associated with it.
384 * The event ring is comprised of multiple segments of the same size.
385 * The HC places events on the ring and "updates the Cycle bit in the TRBs to
386 * indicate to software the current position of the Enqueue Pointer."
387 * The HCD (Linux) processes those events and updates the dequeue pointer.
388 */
389 struct xhci_intr_reg {
390 volatile __le32 irq_pending;
391 volatile __le32 irq_control;
392 volatile __le32 erst_size;
393 volatile __le32 rsvd;
394 volatile __le64 erst_base;
395 volatile __le64 erst_dequeue;
396 };
397
398 /* irq_pending bitmasks */
399 #define ER_IRQ_PENDING(p) ((p) & 0x1)
400 /* bits 2:31 need to be preserved */
401 /* THIS IS BUGGY - FIXME - IP IS WRITE 1 TO CLEAR */
402 #define ER_IRQ_CLEAR(p) ((p) & 0xfffffffe)
403 #define ER_IRQ_ENABLE(p) ((ER_IRQ_CLEAR(p)) | 0x2)
404 #define ER_IRQ_DISABLE(p) ((ER_IRQ_CLEAR(p)) & ~(0x2))
405
406 /* irq_control bitmasks */
407 /* Minimum interval between interrupts (in 250ns intervals). The interval
408 * between interrupts will be longer if there are no events on the event ring.
409 * Default is 4000 (1 ms).
410 */
411 #define ER_IRQ_INTERVAL_MASK (0xffff)
412 /* Counter used to count down the time to the next interrupt - HW use only */
413 #define ER_IRQ_COUNTER_MASK (0xffff << 16)
414
415 /* erst_size bitmasks */
416 /* Preserve bits 16:31 of erst_size */
417 #define ERST_SIZE_MASK (0xffff << 16)
418
419 /* erst_dequeue bitmasks */
420 /* Dequeue ERST Segment Index (DESI) - Segment number (or alias)
421 * where the current dequeue pointer lies. This is an optional HW hint.
422 */
423 #define ERST_DESI_MASK (0x7)
424 /* Event Handler Busy (EHB) - is the event ring scheduled to be serviced by
425 * a work queue (or delayed service routine)?
426 */
427 #define ERST_EHB (1 << 3)
428 #define ERST_PTR_MASK (0xf)
429
430 /**
431 * struct xhci_run_regs
432 * @microframe_index: MFINDEX - current microframe number
433 *
434 * Section 5.5 Host Controller Runtime Registers:
435 * "Software should read and write these registers using only Dword (32 bit)
436 * or larger accesses"
437 */
438 struct xhci_run_regs {
439 __le32 microframe_index;
440 __le32 rsvd[7];
441 struct xhci_intr_reg ir_set[128];
442 };
443
444 /**
445 * struct doorbell_array
446 *
447 * Bits 0 - 7: Endpoint target
448 * Bits 8 - 15: RsvdZ
449 * Bits 16 - 31: Stream ID
450 *
451 * Section 5.6
452 */
453 struct xhci_doorbell_array {
454 volatile __le32 doorbell[256];
455 };
456
457 #define DB_VALUE(ep, stream) ((((ep) + 1) & 0xff) | ((stream) << 16))
458 #define DB_VALUE_HOST 0x00000000
459
460 /**
461 * struct xhci_protocol_caps
462 * @revision: major revision, minor revision, capability ID,
463 * and next capability pointer.
464 * @name_string: Four ASCII characters to say which spec this xHC
465 * follows, typically "USB ".
466 * @port_info: Port offset, count, and protocol-defined information.
467 */
468 struct xhci_protocol_caps {
469 u32 revision;
470 u32 name_string;
471 u32 port_info;
472 };
473
474 #define XHCI_EXT_PORT_MAJOR(x) (((x) >> 24) & 0xff)
475 #define XHCI_EXT_PORT_OFF(x) ((x) & 0xff)
476 #define XHCI_EXT_PORT_COUNT(x) (((x) >> 8) & 0xff)
477
478 /**
479 * struct xhci_container_ctx
480 * @type: Type of context. Used to calculated offsets to contained contexts.
481 * @size: Size of the context data
482 * @bytes: The raw context data given to HW
483 *
484 * Represents either a Device or Input context. Holds a pointer to the raw
485 * memory used for the context (bytes).
486 */
487 struct xhci_container_ctx {
488 unsigned type;
489 #define XHCI_CTX_TYPE_DEVICE 0x1
490 #define XHCI_CTX_TYPE_INPUT 0x2
491
492 int size;
493 u8 *bytes;
494 };
495
496 /**
497 * struct xhci_slot_ctx
498 * @dev_info: Route string, device speed, hub info, and last valid endpoint
499 * @dev_info2: Max exit latency for device number, root hub port number
500 * @tt_info: tt_info is used to construct split transaction tokens
501 * @dev_state: slot state and device address
502 *
503 * Slot Context - section 6.2.1.1. This assumes the HC uses 32-byte context
504 * structures. If the HC uses 64-byte contexts, there is an additional 32 bytes
505 * reserved at the end of the slot context for HC internal use.
506 */
507 struct xhci_slot_ctx {
508 __le32 dev_info;
509 __le32 dev_info2;
510 __le32 tt_info;
511 __le32 dev_state;
512 /* offset 0x10 to 0x1f reserved for HC internal use */
513 __le32 reserved[4];
514 };
515
516 /* dev_info bitmasks */
517 /* Route String - 0:19 */
518 #define ROUTE_STRING_MASK (0xfffff)
519 /* Device speed - values defined by PORTSC Device Speed field - 20:23 */
520 #define DEV_SPEED (0xf << 20)
521 /* bit 24 reserved */
522 /* Is this LS/FS device connected through a HS hub? - bit 25 */
523 #define DEV_MTT (0x1 << 25)
524 /* Set if the device is a hub - bit 26 */
525 #define DEV_HUB (0x1 << 26)
526 /* Index of the last valid endpoint context in this device context - 27:31 */
527 #define LAST_CTX_MASK (0x1f << 27)
528 #define LAST_CTX(p) ((p) << 27)
529 #define LAST_CTX_TO_EP_NUM(p) (((p) >> 27) - 1)
530 #define SLOT_FLAG (1 << 0)
531 #define EP0_FLAG (1 << 1)
532
533 /* dev_info2 bitmasks */
534 /* Max Exit Latency (ms) - worst case time to wake up all links in dev path */
535 #define MAX_EXIT (0xffff)
536 /* Root hub port number that is needed to access the USB device */
537 #define ROOT_HUB_PORT(p) (((p) & 0xff) << 16)
538 #define ROOT_HUB_PORT_MASK (0xff)
539 #define ROOT_HUB_PORT_SHIFT (16)
540 #define DEVINFO_TO_ROOT_HUB_PORT(p) (((p) >> 16) & 0xff)
541 /* Maximum number of ports under a hub device */
542 #define XHCI_MAX_PORTS(p) (((p) & 0xff) << 24)
543
544 /* tt_info bitmasks */
545 /*
546 * TT Hub Slot ID - for low or full speed devices attached to a high-speed hub
547 * The Slot ID of the hub that isolates the high speed signaling from
548 * this low or full-speed device. '0' if attached to root hub port.
549 */
550 #define TT_SLOT(p) (((p) & 0xff) << 0)
551 /*
552 * The number of the downstream facing port of the high-speed hub
553 * '0' if the device is not low or full speed.
554 */
555 #define TT_PORT(p) (((p) & 0xff) << 8)
556 #define TT_THINK_TIME(p) (((p) & 0x3) << 16)
557
558 /* dev_state bitmasks */
559 /* USB device address - assigned by the HC */
560 #define DEV_ADDR_MASK (0xff)
561 /* bits 8:26 reserved */
562 /* Slot state */
563 #define SLOT_STATE (0x1f << 27)
564 #define GET_SLOT_STATE(p) (((p) & (0x1f << 27)) >> 27)
565
566 #define SLOT_STATE_DISABLED 0
567 #define SLOT_STATE_ENABLED SLOT_STATE_DISABLED
568 #define SLOT_STATE_DEFAULT 1
569 #define SLOT_STATE_ADDRESSED 2
570 #define SLOT_STATE_CONFIGURED 3
571
572 /**
573 * struct xhci_ep_ctx
574 * @ep_info: endpoint state, streams, mult, and interval information.
575 * @ep_info2: information on endpoint type, max packet size, max burst size,
576 * error count, and whether the HC will force an event for all
577 * transactions.
578 * @deq: 64-bit ring dequeue pointer address. If the endpoint only
579 * defines one stream, this points to the endpoint transfer ring.
580 * Otherwise, it points to a stream context array, which has a
581 * ring pointer for each flow.
582 * @tx_info:
583 * Average TRB lengths for the endpoint ring and
584 * max payload within an Endpoint Service Interval Time (ESIT).
585 *
586 * Endpoint Context - section 6.2.1.2.This assumes the HC uses 32-byte context
587 * structures.If the HC uses 64-byte contexts, there is an additional 32 bytes
588 * reserved at the end of the endpoint context for HC internal use.
589 */
590 struct xhci_ep_ctx {
591 __le32 ep_info;
592 __le32 ep_info2;
593 __le64 deq;
594 __le32 tx_info;
595 /* offset 0x14 - 0x1f reserved for HC internal use */
596 __le32 reserved[3];
597 };
598
599 /* ep_info bitmasks */
600 /*
601 * Endpoint State - bits 0:2
602 * 0 - disabled
603 * 1 - running
604 * 2 - halted due to halt condition - ok to manipulate endpoint ring
605 * 3 - stopped
606 * 4 - TRB error
607 * 5-7 - reserved
608 */
609 #define EP_STATE_MASK (0xf)
610 #define EP_STATE_DISABLED 0
611 #define EP_STATE_RUNNING 1
612 #define EP_STATE_HALTED 2
613 #define EP_STATE_STOPPED 3
614 #define EP_STATE_ERROR 4
615 /* Mult - Max number of burtst within an interval, in EP companion desc. */
616 #define EP_MULT(p) (((p) & 0x3) << 8)
617 #define CTX_TO_EP_MULT(p) (((p) >> 8) & 0x3)
618 /* bits 10:14 are Max Primary Streams */
619 /* bit 15 is Linear Stream Array */
620 /* Interval - period between requests to an endpoint - 125u increments. */
621 #define EP_INTERVAL(p) (((p) & 0xff) << 16)
622 #define EP_INTERVAL_TO_UFRAMES(p) (1 << (((p) >> 16) & 0xff))
623 #define CTX_TO_EP_INTERVAL(p) (((p) >> 16) & 0xff)
624 #define EP_MAXPSTREAMS_MASK (0x1f << 10)
625 #define EP_MAXPSTREAMS(p) (((p) << 10) & EP_MAXPSTREAMS_MASK)
626 /* Endpoint is set up with a Linear Stream Array (vs. Secondary Stream Array) */
627 #define EP_HAS_LSA (1 << 15)
628
629 /* ep_info2 bitmasks */
630 /*
631 * Force Event - generate transfer events for all TRBs for this endpoint
632 * This will tell the HC to ignore the IOC and ISP flags (for debugging only).
633 */
634 #define FORCE_EVENT (0x1)
635 #define ERROR_COUNT(p) (((p) & 0x3) << 1)
636 #define CTX_TO_EP_TYPE(p) (((p) >> 3) & 0x7)
637 #define EP_TYPE(p) ((p) << 3)
638 #define ISOC_OUT_EP 1
639 #define BULK_OUT_EP 2
640 #define INT_OUT_EP 3
641 #define CTRL_EP 4
642 #define ISOC_IN_EP 5
643 #define BULK_IN_EP 6
644 #define INT_IN_EP 7
645 /* bit 6 reserved */
646 /* bit 7 is Host Initiate Disable - for disabling stream selection */
647 #define MAX_BURST(p) (((p)&0xff) << 8)
648 #define CTX_TO_MAX_BURST(p) (((p) >> 8) & 0xff)
649 #define MAX_PACKET(p) (((p)&0xffff) << 16)
650 #define MAX_PACKET_MASK (0xffff)
651 #define MAX_PACKET_DECODED(p) (((p) >> 16) & 0xffff)
652
653 /* Get max packet size from ep desc. Bit 10..0 specify the max packet size.
654 * USB2.0 spec 9.6.6.
655 */
656 #define GET_MAX_PACKET(p) ((p) & 0x7ff)
657
658 /* tx_info bitmasks */
659 #define EP_AVG_TRB_LENGTH(p) ((p) & 0xffff)
660 #define EP_MAX_ESIT_PAYLOAD_LO(p) (((p) & 0xffff) << 16)
661 #define EP_MAX_ESIT_PAYLOAD_HI(p) ((((p) >> 16) & 0xff) << 24)
662 #define CTX_TO_MAX_ESIT_PAYLOAD(p) (((p) >> 16) & 0xffff)
663
664 /* deq bitmasks */
665 #define EP_CTX_CYCLE_MASK (1 << 0)
666
667 /* reserved[0] bitmasks, MediaTek xHCI used */
668 #define EP_BPKTS(p) (((p) & 0x7f) << 0)
669 #define EP_BBM(p) (((p) & 0x1) << 11)
670
671 /**
672 * struct xhci_input_control_context
673 * Input control context; see section 6.2.5.
674 *
675 * @drop_context: set the bit of the endpoint context you want to disable
676 * @add_context: set the bit of the endpoint context you want to enable
677 */
678 struct xhci_input_control_ctx {
679 volatile __le32 drop_flags;
680 volatile __le32 add_flags;
681 __le32 rsvd2[6];
682 };
683
684
685 /**
686 * struct xhci_device_context_array
687 * @dev_context_ptr array of 64-bit DMA addresses for device contexts
688 */
689 struct xhci_device_context_array {
690 /* 64-bit device addresses; we only write 32-bit addresses */
691 __le64 dev_context_ptrs[MAX_HC_SLOTS];
692 };
693 /* TODO: write function to set the 64-bit device DMA address */
694 /*
695 * TODO: change this to be dynamically sized at HC mem init time since the HC
696 * might not be able to handle the maximum number of devices possible.
697 */
698
699
700 struct xhci_transfer_event {
701 /* 64-bit buffer address, or immediate data */
702 __le64 buffer;
703 __le32 transfer_len;
704 /* This field is interpreted differently based on the type of TRB */
705 volatile __le32 flags;
706 };
707
708 /* Transfer event TRB length bit mask */
709 /* bits 0:23 */
710 #define EVENT_TRB_LEN(p) ((p) & 0xffffff)
711
712 /** Transfer Event bit fields **/
713 #define TRB_TO_EP_ID(p) (((p) >> 16) & 0x1f)
714
715 /* Completion Code - only applicable for some types of TRBs */
716 #define COMP_CODE_MASK (0xff << 24)
717 #define COMP_CODE_SHIFT (24)
718 #define GET_COMP_CODE(p) (((p) & COMP_CODE_MASK) >> 24)
719
720 typedef enum {
721 COMP_SUCCESS = 1,
722 /* Data Buffer Error */
723 COMP_DB_ERR, /* 2 */
724 /* Babble Detected Error */
725 COMP_BABBLE, /* 3 */
726 /* USB Transaction Error */
727 COMP_TX_ERR, /* 4 */
728 /* TRB Error - some TRB field is invalid */
729 COMP_TRB_ERR, /* 5 */
730 /* Stall Error - USB device is stalled */
731 COMP_STALL, /* 6 */
732 /* Resource Error - HC doesn't have memory for that device configuration */
733 COMP_ENOMEM, /* 7 */
734 /* Bandwidth Error - not enough room in schedule for this dev config */
735 COMP_BW_ERR, /* 8 */
736 /* No Slots Available Error - HC ran out of device slots */
737 COMP_ENOSLOTS, /* 9 */
738 /* Invalid Stream Type Error */
739 COMP_STREAM_ERR, /* 10 */
740 /* Slot Not Enabled Error - doorbell rung for disabled device slot */
741 COMP_EBADSLT, /* 11 */
742 /* Endpoint Not Enabled Error */
743 COMP_EBADEP,/* 12 */
744 /* Short Packet */
745 COMP_SHORT_TX, /* 13 */
746 /* Ring Underrun - doorbell rung for an empty isoc OUT ep ring */
747 COMP_UNDERRUN, /* 14 */
748 /* Ring Overrun - isoc IN ep ring is empty when ep is scheduled to RX */
749 COMP_OVERRUN, /* 15 */
750 /* Virtual Function Event Ring Full Error */
751 COMP_VF_FULL, /* 16 */
752 /* Parameter Error - Context parameter is invalid */
753 COMP_EINVAL, /* 17 */
754 /* Bandwidth Overrun Error - isoc ep exceeded its allocated bandwidth */
755 COMP_BW_OVER,/* 18 */
756 /* Context State Error - illegal context state transition requested */
757 COMP_CTX_STATE,/* 19 */
758 /* No Ping Response Error - HC didn't get PING_RESPONSE in time to TX */
759 COMP_PING_ERR,/* 20 */
760 /* Event Ring is full */
761 COMP_ER_FULL,/* 21 */
762 /* Incompatible Device Error */
763 COMP_DEV_ERR,/* 22 */
764 /* Missed Service Error - HC couldn't service an isoc ep within interval */
765 COMP_MISSED_INT,/* 23 */
766 /* Successfully stopped command ring */
767 COMP_CMD_STOP, /* 24 */
768 /* Successfully aborted current command and stopped command ring */
769 COMP_CMD_ABORT, /* 25 */
770 /* Stopped - transfer was terminated by a stop endpoint command */
771 COMP_STOP,/* 26 */
772 /* Same as COMP_EP_STOPPED, but the transferred length in the event
773 * is invalid */
774 COMP_STOP_INVAL, /* 27*/
775 /* Control Abort Error - Debug Capability - control pipe aborted */
776 COMP_DBG_ABORT, /* 28 */
777 /* Max Exit Latency Too Large Error */
778 COMP_MEL_ERR,/* 29 */
779 /* TRB type 30 reserved */
780 /* Isoc Buffer Overrun - an isoc IN ep sent more data than could fit in TD */
781 COMP_BUFF_OVER = 31,
782 /* Event Lost Error - xHC has an "internal event overrun condition" */
783 COMP_ISSUES, /* 32 */
784 /* Undefined Error - reported when other error codes don't apply */
785 COMP_UNKNOWN, /* 33 */
786 /* Invalid Stream ID Error */
787 COMP_STRID_ERR, /* 34 */
788 /* Secondary Bandwidth Error - may be returned by a Configure Endpoint cmd */
789 COMP_2ND_BW_ERR, /* 35 */
790 /* Split Transaction Error */
791 COMP_SPLIT_ERR /* 36 */
792
793 } xhci_comp_code;
794
795 struct xhci_link_trb {
796 /* 64-bit segment pointer*/
797 volatile __le64 segment_ptr;
798 volatile __le32 intr_target;
799 volatile __le32 control;
800 };
801
802 /* control bitfields */
803 #define LINK_TOGGLE (0x1 << 1)
804
805 /* Command completion event TRB */
806 struct xhci_event_cmd {
807 /* Pointer to command TRB, or the value passed by the event data trb */
808 volatile __le64 cmd_trb;
809 volatile __le32 status;
810 volatile __le32 flags;
811 };
812
813 /* flags bitmasks */
814 /* bits 16:23 are the virtual function ID */
815 /* bits 24:31 are the slot ID */
816 #define TRB_TO_SLOT_ID(p) (((p) & (0xff << 24)) >> 24)
817 #define TRB_TO_SLOT_ID_SHIFT (24)
818 #define TRB_TO_SLOT_ID_MASK (0xff << TRB_TO_SLOT_ID_SHIFT)
819 #define SLOT_ID_FOR_TRB(p) (((p) & 0xff) << 24)
820 #define SLOT_ID_FOR_TRB_MASK (0xff)
821 #define SLOT_ID_FOR_TRB_SHIFT (24)
822
823 /* Stop Endpoint TRB - ep_index to endpoint ID for this TRB */
824 #define TRB_TO_EP_INDEX(p) ((((p) & (0x1f << 16)) >> 16) - 1)
825 #define EP_ID_FOR_TRB(p) ((((p) + 1) & 0x1f) << 16)
826
827 #define SUSPEND_PORT_FOR_TRB(p) (((p) & 1) << 23)
828 #define TRB_TO_SUSPEND_PORT(p) (((p) & (1 << 23)) >> 23)
829 #define LAST_EP_INDEX 30
830
831 /* Set TR Dequeue Pointer command TRB fields */
832 #define TRB_TO_STREAM_ID(p) ((((p) & (0xffff << 16)) >> 16))
833 #define STREAM_ID_FOR_TRB(p) ((((p)) & 0xffff) << 16)
834
835
836 /* Port Status Change Event TRB fields */
837 /* Port ID - bits 31:24 */
838 #define GET_PORT_ID(p) (((p) & (0xff << 24)) >> 24)
839 #define PORT_ID_SHIFT (24)
840 #define PORT_ID_MASK (0xff << PORT_ID_SHIFT)
841
842 /* Normal TRB fields */
843 /* transfer_len bitmasks - bits 0:16 */
844 #define TRB_LEN(p) ((p) & 0x1ffff)
845 /* TD Size, packets remaining in this TD, bits 21:17 (5 bits, so max 31) */
846 #define TRB_TD_SIZE(p) (min((p), (u32)31) << 17)
847 /* Interrupter Target - which MSI-X vector to target the completion event at */
848 #define TRB_INTR_TARGET(p) (((p) & 0x3ff) << 22)
849 #define GET_INTR_TARGET(p) (((p) >> 22) & 0x3ff)
850 #define TRB_TBC(p) (((p) & 0x3) << 7)
851 #define TRB_TLBPC(p) (((p) & 0xf) << 16)
852
853 /* Cycle bit - indicates TRB ownership by HC or HCD */
854 #define TRB_CYCLE (1<<0)
855 /*
856 * Force next event data TRB to be evaluated before task switch.
857 * Used to pass OS data back after a TD completes.
858 */
859 #define TRB_ENT (1<<1)
860 /* Interrupt on short packet */
861 #define TRB_ISP (1<<2)
862 /* Set PCIe no snoop attribute */
863 #define TRB_NO_SNOOP (1<<3)
864 /* Chain multiple TRBs into a TD */
865 #define TRB_CHAIN (1<<4)
866 /* Interrupt on completion */
867 #define TRB_IOC (1<<5)
868 /* The buffer pointer contains immediate data */
869 #define TRB_IDT (1<<6)
870
871 /* Block Event Interrupt */
872 #define TRB_BEI (1<<9)
873
874 /* Control transfer TRB specific fields */
875 #define TRB_DIR_IN (1<<16)
876 #define TRB_TX_TYPE(p) ((p) << 16)
877 #define TRB_DATA_OUT 2
878 #define TRB_DATA_IN 3
879
880 /* Isochronous TRB specific fields */
881 #define TRB_SIA (1 << 31)
882
883 struct xhci_generic_trb {
884 volatile __le32 field[4];
885 };
886
887 union xhci_trb {
888 struct xhci_link_trb link;
889 struct xhci_transfer_event trans_event;
890 struct xhci_event_cmd event_cmd;
891 struct xhci_generic_trb generic;
892 };
893
894 /* TRB bit mask */
895 #define TRB_TYPE_BITMASK (0xfc00)
896 #define TRB_TYPE(p) ((p) << 10)
897 #define TRB_FIELD_TO_TYPE(p) (((p) & TRB_TYPE_BITMASK) >> 10)
898
899 /* TRB type IDs */
900 typedef enum {
901 /* bulk, interrupt, isoc scatter/gather, and control data stage */
902 TRB_NORMAL = 1,
903 /* setup stage for control transfers */
904 TRB_SETUP, /* 2 */
905 /* data stage for control transfers */
906 TRB_DATA, /* 3 */
907 /* status stage for control transfers */
908 TRB_STATUS, /* 4 */
909 /* isoc transfers */
910 TRB_ISOC, /* 5 */
911 /* TRB for linking ring segments */
912 TRB_LINK, /* 6 */
913 /* TRB for EVENT DATA */
914 TRB_EVENT_DATA, /* 7 */
915 /* Transfer Ring No-op (not for the command ring) */
916 TRB_TR_NOOP, /* 8 */
917 /* Command TRBs */
918 /* Enable Slot Command */
919 TRB_ENABLE_SLOT, /* 9 */
920 /* Disable Slot Command */
921 TRB_DISABLE_SLOT, /* 10 */
922 /* Address Device Command */
923 TRB_ADDR_DEV, /* 11 */
924 /* Configure Endpoint Command */
925 TRB_CONFIG_EP, /* 12 */
926 /* Evaluate Context Command */
927 TRB_EVAL_CONTEXT, /* 13 */
928 /* Reset Endpoint Command */
929 TRB_RESET_EP, /* 14 */
930 /* Stop Transfer Ring Command */
931 TRB_STOP_RING, /* 15 */
932 /* Set Transfer Ring Dequeue Pointer Command */
933 TRB_SET_DEQ, /* 16 */
934 /* Reset Device Command */
935 TRB_RESET_DEV, /* 17 */
936 /* Force Event Command (opt) */
937 TRB_FORCE_EVENT, /* 18 */
938 /* Negotiate Bandwidth Command (opt) */
939 TRB_NEG_BANDWIDTH, /* 19 */
940 /* Set Latency Tolerance Value Command (opt) */
941 TRB_SET_LT, /* 20 */
942 /* Get port bandwidth Command */
943 TRB_GET_BW, /* 21 */
944 /* Force Header Command - generate a transaction or link management packet */
945 TRB_FORCE_HEADER, /* 22 */
946 /* No-op Command - not for transfer rings */
947 TRB_CMD_NOOP, /* 23 */
948 /* TRB IDs 24-31 reserved */
949 /* Event TRBS */
950 /* Transfer Event */
951 TRB_TRANSFER = 32,
952 /* Command Completion Event */
953 TRB_COMPLETION, /* 33 */
954 /* Port Status Change Event */
955 TRB_PORT_STATUS, /* 34 */
956 /* Bandwidth Request Event (opt) */
957 TRB_BANDWIDTH_EVENT, /* 35 */
958 /* Doorbell Event (opt) */
959 TRB_DOORBELL, /* 36 */
960 /* Host Controller Event */
961 TRB_HC_EVENT, /* 37 */
962 /* Device Notification Event - device sent function wake notification */
963 TRB_DEV_NOTE, /* 38 */
964 /* MFINDEX Wrap Event - microframe counter wrapped */
965 TRB_MFINDEX_WRAP, /* 39 */
966 /* TRB IDs 40-47 reserved, 48-63 is vendor-defined */
967 /* Nec vendor-specific command completion event. */
968 TRB_NEC_CMD_COMP = 48, /* 48 */
969 /* Get NEC firmware revision. */
970 TRB_NEC_GET_FW, /* 49 */
971 } trb_type;
972
973 #define TRB_TYPE_LINK(x) (((x) & TRB_TYPE_BITMASK) == TRB_TYPE(TRB_LINK))
974 /* Above, but for __le32 types -- can avoid work by swapping constants: */
975 #define TRB_TYPE_LINK_LE32(x) (((x) & cpu_to_le32(TRB_TYPE_BITMASK)) == \
976 cpu_to_le32(TRB_TYPE(TRB_LINK)))
977 #define TRB_TYPE_NOOP_LE32(x) (((x) & cpu_to_le32(TRB_TYPE_BITMASK)) == \
978 cpu_to_le32(TRB_TYPE(TRB_TR_NOOP)))
979
980 /*
981 * TRBS_PER_SEGMENT must be a multiple of 4,
982 * since the command ring is 64-byte aligned.
983 * It must also be greater than 16.
984 */
985 #define TRBS_PER_SEGMENT 64
986 /* Allow two commands + a link TRB, along with any reserved command TRBs */
987 #define MAX_RSVD_CMD_TRBS (TRBS_PER_SEGMENT - 3)
988 #define SEGMENT_SIZE (TRBS_PER_SEGMENT*16)
989 /* SEGMENT_SHIFT should be log2(SEGMENT_SIZE).
990 * Change this if you change TRBS_PER_SEGMENT!
991 */
992 #define SEGMENT_SHIFT 10
993 /* TRB buffer pointers can't cross 64KB boundaries */
994 #define TRB_MAX_BUFF_SHIFT 16
995 #define TRB_MAX_BUFF_SIZE (1 << TRB_MAX_BUFF_SHIFT)
996
997 struct xhci_segment {
998 union xhci_trb *trbs;
999 /* private to HCD */
1000 struct xhci_segment *next;
1001 };
1002
1003 struct xhci_ring {
1004 struct xhci_segment *first_seg;
1005 union xhci_trb *enqueue;
1006 struct xhci_segment *enq_seg;
1007 union xhci_trb *dequeue;
1008 struct xhci_segment *deq_seg;
1009 /*
1010 * Write the cycle state into the TRB cycle field to give ownership of
1011 * the TRB to the host controller (if we are the producer), or to check
1012 * if we own the TRB (if we are the consumer). See section 4.9.1.
1013 */
1014 volatile u32 cycle_state;
1015 unsigned int num_segs;
1016 };
1017
1018 struct xhci_erst_entry {
1019 /* 64-bit event ring segment address */
1020 __le64 seg_addr;
1021 __le32 seg_size;
1022 /* Set to zero */
1023 __le32 rsvd;
1024 };
1025
1026 struct xhci_erst {
1027 struct xhci_erst_entry *entries;
1028 unsigned int num_entries;
1029 /* Num entries the ERST can contain */
1030 unsigned int erst_size;
1031 };
1032
1033 struct xhci_scratchpad {
1034 u64 *sp_array;
1035 };
1036
1037 /*
1038 * Each segment table entry is 4*32bits long. 1K seems like an ok size:
1039 * (1K bytes * 8bytes/bit) / (4*32 bits) = 64 segment entries in the table,
1040 * meaning 64 ring segments.
1041 * Initial allocated size of the ERST, in number of entries */
1042 #define ERST_NUM_SEGS 1
1043 /* Initial number of event segment rings allocated */
1044 #define ERST_ENTRIES 1
1045 /* Initial allocated size of the ERST, in number of entries */
1046 #define ERST_SIZE 64
1047 /* Poll every 60 seconds */
1048 #define POLL_TIMEOUT 60
1049 /* Stop endpoint command timeout (secs) for URB cancellation watchdog timer */
1050 #define XHCI_STOP_EP_CMD_TIMEOUT 5
1051 /* XXX: Make these module parameters */
1052
1053 struct xhci_virt_ep {
1054 struct xhci_ring *ring;
1055 unsigned int ep_state;
1056 #define SET_DEQ_PENDING (1 << 0)
1057 #define EP_HALTED (1 << 1) /* For stall handling */
1058 #define EP_HALT_PENDING (1 << 2) /* For URB cancellation */
1059 /* Transitioning the endpoint to using streams, don't enqueue URBs */
1060 #define EP_GETTING_STREAMS (1 << 3)
1061 #define EP_HAS_STREAMS (1 << 4)
1062 /* Transitioning the endpoint to not using streams, don't enqueue URBs */
1063 #define EP_GETTING_NO_STREAMS (1 << 5)
1064 };
1065
1066 #define CTX_SIZE(_hcc) (HCC_64BYTE_CONTEXT(_hcc) ? 64 : 32)
1067
1068 struct xhci_virt_device {
1069 struct usb_device *udev;
1070 /*
1071 * Commands to the hardware are passed an "input context" that
1072 * tells the hardware what to change in its data structures.
1073 * The hardware will return changes in an "output context" that
1074 * software must allocate for the hardware. We need to keep
1075 * track of input and output contexts separately because
1076 * these commands might fail and we don't trust the hardware.
1077 */
1078 struct xhci_container_ctx *out_ctx;
1079 /* Used for addressing devices and configuration changes */
1080 struct xhci_container_ctx *in_ctx;
1081 /* Rings saved to ensure old alt settings can be re-instated */
1082 #define XHCI_MAX_RINGS_CACHED 31
1083 struct xhci_virt_ep eps[31];
1084 };
1085
1086 /* TODO: copied from ehci.h - can be refactored? */
1087 /* xHCI spec says all registers are little endian */
xhci_readl(uint32_t volatile * regs)1088 static inline unsigned int xhci_readl(uint32_t volatile *regs)
1089 {
1090 return readl(regs);
1091 }
1092
xhci_writel(uint32_t volatile * regs,const unsigned int val)1093 static inline void xhci_writel(uint32_t volatile *regs, const unsigned int val)
1094 {
1095 writel(val, regs);
1096 }
1097
1098 /*
1099 * Registers should always be accessed with double word or quad word accesses.
1100 * Some xHCI implementations may support 64-bit address pointers. Registers
1101 * with 64-bit address pointers should be written to with dword accesses by
1102 * writing the low dword first (ptr[0]), then the high dword (ptr[1]) second.
1103 * xHCI implementations that do not support 64-bit address pointers will ignore
1104 * the high dword, and write order is irrelevant.
1105 */
xhci_readq(__le64 volatile * regs)1106 static inline u64 xhci_readq(__le64 volatile *regs)
1107 {
1108 __u32 *ptr = (__u32 *)regs;
1109 u64 val_lo = readl(ptr);
1110 u64 val_hi = readl(ptr + 1);
1111 return val_lo + (val_hi << 32);
1112 }
1113
xhci_writeq(__le64 volatile * regs,const u64 val)1114 static inline void xhci_writeq(__le64 volatile *regs, const u64 val)
1115 {
1116 __u32 *ptr = (__u32 *)regs;
1117 u32 val_lo = lower_32_bits(val);
1118 /* FIXME */
1119 u32 val_hi = upper_32_bits(val);
1120 writel(val_lo, ptr);
1121 writel(val_hi, ptr + 1);
1122 }
1123
1124 int xhci_hcd_init(int index, struct xhci_hccr **ret_hccr,
1125 struct xhci_hcor **ret_hcor);
1126 void xhci_hcd_stop(int index);
1127
1128
1129 /*************************************************************
1130 EXTENDED CAPABILITY DEFINITIONS
1131 *************************************************************/
1132 /* Up to 16 ms to halt an HC */
1133 #define XHCI_MAX_HALT_USEC (16*1000)
1134 /* HC not running - set to 1 when run/stop bit is cleared. */
1135 #define XHCI_STS_HALT (1 << 0)
1136
1137 /* HCCPARAMS offset from PCI base address */
1138 #define XHCI_HCC_PARAMS_OFFSET 0x10
1139 /* HCCPARAMS contains the first extended capability pointer */
1140 #define XHCI_HCC_EXT_CAPS(p) (((p)>>16)&0xffff)
1141
1142 /* Command and Status registers offset from the Operational Registers address */
1143 #define XHCI_CMD_OFFSET 0x00
1144 #define XHCI_STS_OFFSET 0x04
1145
1146 #define XHCI_MAX_EXT_CAPS 50
1147
1148 /* Capability Register */
1149 /* bits 7:0 - how long is the Capabilities register */
1150 #define XHCI_HC_LENGTH(p) (((p) >> 00) & 0x00ff)
1151
1152 /* Extended capability register fields */
1153 #define XHCI_EXT_CAPS_ID(p) (((p) >> 0) & 0xff)
1154 #define XHCI_EXT_CAPS_NEXT(p) (((p) >> 8) & 0xff)
1155 #define XHCI_EXT_CAPS_VAL(p) ((p) >> 16)
1156 /* Extended capability IDs - ID 0 reserved */
1157 #define XHCI_EXT_CAPS_LEGACY 1
1158 #define XHCI_EXT_CAPS_PROTOCOL 2
1159 #define XHCI_EXT_CAPS_PM 3
1160 #define XHCI_EXT_CAPS_VIRT 4
1161 #define XHCI_EXT_CAPS_ROUTE 5
1162 /* IDs 6-9 reserved */
1163 #define XHCI_EXT_CAPS_DEBUG 10
1164 /* USB Legacy Support Capability - section 7.1.1 */
1165 #define XHCI_HC_BIOS_OWNED (1 << 16)
1166 #define XHCI_HC_OS_OWNED (1 << 24)
1167
1168 /* USB Legacy Support Capability - section 7.1.1 */
1169 /* Add this offset, plus the value of xECP in HCCPARAMS to the base address */
1170 #define XHCI_LEGACY_SUPPORT_OFFSET (0x00)
1171
1172 /* USB Legacy Support Control and Status Register - section 7.1.2 */
1173 /* Add this offset, plus the value of xECP in HCCPARAMS to the base address */
1174 #define XHCI_LEGACY_CONTROL_OFFSET (0x04)
1175 /* bits 1:2, 5:12, and 17:19 need to be preserved; bits 21:28 should be zero */
1176 #define XHCI_LEGACY_DISABLE_SMI ((0x3 << 1) + (0xff << 5) + (0x7 << 17))
1177
1178 /* USB 2.0 xHCI 0.96 L1C capability - section 7.2.2.1.3.2 */
1179 #define XHCI_L1C (1 << 16)
1180
1181 /* USB 2.0 xHCI 1.0 hardware LMP capability - section 7.2.2.1.3.2 */
1182 #define XHCI_HLC (1 << 19)
1183
1184 /* command register values to disable interrupts and halt the HC */
1185 /* start/stop HC execution - do not write unless HC is halted*/
1186 #define XHCI_CMD_RUN (1 << 0)
1187 /* Event Interrupt Enable - get irq when EINT bit is set in USBSTS register */
1188 #define XHCI_CMD_EIE (1 << 2)
1189 /* Host System Error Interrupt Enable - get irq when HSEIE bit set in USBSTS */
1190 #define XHCI_CMD_HSEIE (1 << 3)
1191 /* Enable Wrap Event - '1' means xHC generates an event when MFINDEX wraps. */
1192 #define XHCI_CMD_EWE (1 << 10)
1193
1194 #define XHCI_IRQS (XHCI_CMD_EIE | XHCI_CMD_HSEIE | XHCI_CMD_EWE)
1195
1196 /* true: Controller Not Ready to accept doorbell or op reg writes after reset */
1197 #define XHCI_STS_CNR (1 << 11)
1198
1199 struct xhci_ctrl {
1200 #if CONFIG_IS_ENABLED(DM_USB)
1201 struct udevice *dev;
1202 #endif
1203 struct reset_ctl reset;
1204 struct xhci_hccr *hccr; /* R/O registers, not need for volatile */
1205 struct xhci_hcor *hcor;
1206 struct xhci_doorbell_array *dba;
1207 struct xhci_run_regs *run_regs;
1208 struct xhci_device_context_array *dcbaa \
1209 __attribute__ ((aligned(ARCH_DMA_MINALIGN)));
1210 struct xhci_ring *event_ring;
1211 struct xhci_ring *cmd_ring;
1212 struct xhci_ring *transfer_ring;
1213 struct xhci_segment *seg;
1214 struct xhci_intr_reg *ir_set;
1215 struct xhci_erst erst;
1216 struct xhci_erst_entry entry[ERST_NUM_SEGS];
1217 struct xhci_scratchpad *scratchpad;
1218 struct xhci_virt_device *devs[MAX_HC_SLOTS];
1219 int rootdev;
1220 u16 hci_version;
1221 u32 quirks;
1222 #define XHCI_MTK_HOST BIT(0)
1223 };
1224
1225 #if CONFIG_IS_ENABLED(DM_USB)
1226 #define xhci_to_dev(_ctrl) _ctrl->dev
1227 #else
1228 #define xhci_to_dev(_ctrl) NULL
1229 #endif
1230
1231 unsigned long trb_addr(struct xhci_segment *seg, union xhci_trb *trb);
1232 struct xhci_input_control_ctx
1233 *xhci_get_input_control_ctx(struct xhci_container_ctx *ctx);
1234 struct xhci_slot_ctx *xhci_get_slot_ctx(struct xhci_ctrl *ctrl,
1235 struct xhci_container_ctx *ctx);
1236 struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_ctrl *ctrl,
1237 struct xhci_container_ctx *ctx,
1238 unsigned int ep_index);
1239 void xhci_endpoint_copy(struct xhci_ctrl *ctrl,
1240 struct xhci_container_ctx *in_ctx,
1241 struct xhci_container_ctx *out_ctx,
1242 unsigned int ep_index);
1243 void xhci_slot_copy(struct xhci_ctrl *ctrl,
1244 struct xhci_container_ctx *in_ctx,
1245 struct xhci_container_ctx *out_ctx);
1246 void xhci_setup_addressable_virt_dev(struct xhci_ctrl *ctrl,
1247 struct usb_device *udev, int hop_portnr);
1248 void xhci_queue_command(struct xhci_ctrl *ctrl, u8 *ptr,
1249 u32 slot_id, u32 ep_index, trb_type cmd);
1250 void xhci_acknowledge_event(struct xhci_ctrl *ctrl);
1251 union xhci_trb *xhci_wait_for_event(struct xhci_ctrl *ctrl, trb_type expected);
1252 int xhci_bulk_tx(struct usb_device *udev, unsigned long pipe,
1253 int length, void *buffer);
1254 int xhci_ctrl_tx(struct usb_device *udev, unsigned long pipe,
1255 struct devrequest *req, int length, void *buffer);
1256 int xhci_check_maxpacket(struct usb_device *udev);
1257 void xhci_flush_cache(uintptr_t addr, u32 type_len);
1258 void xhci_inval_cache(uintptr_t addr, u32 type_len);
1259 void xhci_cleanup(struct xhci_ctrl *ctrl);
1260 struct xhci_ring *xhci_ring_alloc(struct xhci_ctrl *ctrl, unsigned int num_segs,
1261 bool link_trbs);
1262 int xhci_alloc_virt_device(struct xhci_ctrl *ctrl, unsigned int slot_id);
1263 int xhci_mem_init(struct xhci_ctrl *ctrl, struct xhci_hccr *hccr,
1264 struct xhci_hcor *hcor);
1265
1266 /**
1267 * xhci_deregister() - Unregister an XHCI controller
1268 *
1269 * @dev: Controller device
1270 * @return 0 if registered, -ve on error
1271 */
1272 int xhci_deregister(struct udevice *dev);
1273
1274 /**
1275 * xhci_register() - Register a new XHCI controller
1276 *
1277 * @dev: Controller device
1278 * @hccr: Host controller control registers
1279 * @hcor: Not sure what this means
1280 * @return 0 if registered, -ve on error
1281 */
1282 int xhci_register(struct udevice *dev, struct xhci_hccr *hccr,
1283 struct xhci_hcor *hcor);
1284
1285 extern struct dm_usb_ops xhci_usb_ops;
1286
1287 struct xhci_ctrl *xhci_get_ctrl(struct usb_device *udev);
1288
xhci_virt_to_bus(struct xhci_ctrl * ctrl,void * addr)1289 static inline dma_addr_t xhci_virt_to_bus(struct xhci_ctrl *ctrl, void *addr)
1290 {
1291 return dev_phys_to_bus(xhci_to_dev(ctrl), virt_to_phys(addr));
1292 }
1293
xhci_bus_to_virt(struct xhci_ctrl * ctrl,dma_addr_t addr)1294 static inline void *xhci_bus_to_virt(struct xhci_ctrl *ctrl, dma_addr_t addr)
1295 {
1296 return phys_to_virt(dev_bus_to_phys(xhci_to_dev(ctrl), addr));
1297 }
1298
1299 #endif /* HOST_XHCI_H_ */
1300