1 // SPDX-License-Identifier: GPL-2.0
2 /* Copyright(c) 2013 - 2019 Intel Corporation. */
3
4 #include "fm10k_vf.h"
5
6 /**
7 * fm10k_stop_hw_vf - Stop Tx/Rx units
8 * @hw: pointer to hardware structure
9 *
10 **/
fm10k_stop_hw_vf(struct fm10k_hw * hw)11 static s32 fm10k_stop_hw_vf(struct fm10k_hw *hw)
12 {
13 u8 *perm_addr = hw->mac.perm_addr;
14 u32 bal = 0, bah = 0, tdlen;
15 s32 err;
16 u16 i;
17
18 /* we need to disable the queues before taking further steps */
19 err = fm10k_stop_hw_generic(hw);
20 if (err && err != FM10K_ERR_REQUESTS_PENDING)
21 return err;
22
23 /* If permanent address is set then we need to restore it */
24 if (is_valid_ether_addr(perm_addr)) {
25 bal = (((u32)perm_addr[3]) << 24) |
26 (((u32)perm_addr[4]) << 16) |
27 (((u32)perm_addr[5]) << 8);
28 bah = (((u32)0xFF) << 24) |
29 (((u32)perm_addr[0]) << 16) |
30 (((u32)perm_addr[1]) << 8) |
31 ((u32)perm_addr[2]);
32 }
33
34 /* restore default itr_scale for next VF initialization */
35 tdlen = hw->mac.itr_scale << FM10K_TDLEN_ITR_SCALE_SHIFT;
36
37 /* The queues have already been disabled so we just need to
38 * update their base address registers
39 */
40 for (i = 0; i < hw->mac.max_queues; i++) {
41 fm10k_write_reg(hw, FM10K_TDBAL(i), bal);
42 fm10k_write_reg(hw, FM10K_TDBAH(i), bah);
43 fm10k_write_reg(hw, FM10K_RDBAL(i), bal);
44 fm10k_write_reg(hw, FM10K_RDBAH(i), bah);
45 /* Restore ITR scale in software-defined mechanism in TDLEN
46 * for next VF initialization. See definition of
47 * FM10K_TDLEN_ITR_SCALE_SHIFT for more details on the use of
48 * TDLEN here.
49 */
50 fm10k_write_reg(hw, FM10K_TDLEN(i), tdlen);
51 }
52
53 return err;
54 }
55
56 /**
57 * fm10k_reset_hw_vf - VF hardware reset
58 * @hw: pointer to hardware structure
59 *
60 * This function should return the hardware to a state similar to the
61 * one it is in after just being initialized.
62 **/
fm10k_reset_hw_vf(struct fm10k_hw * hw)63 static s32 fm10k_reset_hw_vf(struct fm10k_hw *hw)
64 {
65 s32 err;
66
67 /* shut down queues we own and reset DMA configuration */
68 err = fm10k_stop_hw_vf(hw);
69 if (err == FM10K_ERR_REQUESTS_PENDING)
70 hw->mac.reset_while_pending++;
71 else if (err)
72 return err;
73
74 /* Inititate VF reset */
75 fm10k_write_reg(hw, FM10K_VFCTRL, FM10K_VFCTRL_RST);
76
77 /* Flush write and allow 100us for reset to complete */
78 fm10k_write_flush(hw);
79 udelay(FM10K_RESET_TIMEOUT);
80
81 /* Clear reset bit and verify it was cleared */
82 fm10k_write_reg(hw, FM10K_VFCTRL, 0);
83 if (fm10k_read_reg(hw, FM10K_VFCTRL) & FM10K_VFCTRL_RST)
84 return FM10K_ERR_RESET_FAILED;
85
86 return 0;
87 }
88
89 /**
90 * fm10k_init_hw_vf - VF hardware initialization
91 * @hw: pointer to hardware structure
92 *
93 **/
fm10k_init_hw_vf(struct fm10k_hw * hw)94 static s32 fm10k_init_hw_vf(struct fm10k_hw *hw)
95 {
96 u32 tqdloc, tqdloc0 = ~fm10k_read_reg(hw, FM10K_TQDLOC(0));
97 s32 err;
98 u16 i;
99
100 /* verify we have at least 1 queue */
101 if (!~fm10k_read_reg(hw, FM10K_TXQCTL(0)) ||
102 !~fm10k_read_reg(hw, FM10K_RXQCTL(0))) {
103 err = FM10K_ERR_NO_RESOURCES;
104 goto reset_max_queues;
105 }
106
107 /* determine how many queues we have */
108 for (i = 1; tqdloc0 && (i < FM10K_MAX_QUEUES_POOL); i++) {
109 /* verify the Descriptor cache offsets are increasing */
110 tqdloc = ~fm10k_read_reg(hw, FM10K_TQDLOC(i));
111 if (!tqdloc || (tqdloc == tqdloc0))
112 break;
113
114 /* check to verify the PF doesn't own any of our queues */
115 if (!~fm10k_read_reg(hw, FM10K_TXQCTL(i)) ||
116 !~fm10k_read_reg(hw, FM10K_RXQCTL(i)))
117 break;
118 }
119
120 /* shut down queues we own and reset DMA configuration */
121 err = fm10k_disable_queues_generic(hw, i);
122 if (err)
123 goto reset_max_queues;
124
125 /* record maximum queue count */
126 hw->mac.max_queues = i;
127
128 /* fetch default VLAN and ITR scale */
129 hw->mac.default_vid = (fm10k_read_reg(hw, FM10K_TXQCTL(0)) &
130 FM10K_TXQCTL_VID_MASK) >> FM10K_TXQCTL_VID_SHIFT;
131 /* Read the ITR scale from TDLEN. See the definition of
132 * FM10K_TDLEN_ITR_SCALE_SHIFT for more information about how TDLEN is
133 * used here.
134 */
135 hw->mac.itr_scale = (fm10k_read_reg(hw, FM10K_TDLEN(0)) &
136 FM10K_TDLEN_ITR_SCALE_MASK) >>
137 FM10K_TDLEN_ITR_SCALE_SHIFT;
138
139 return 0;
140
141 reset_max_queues:
142 hw->mac.max_queues = 0;
143
144 return err;
145 }
146
147 /* This structure defines the attibutes to be parsed below */
148 const struct fm10k_tlv_attr fm10k_mac_vlan_msg_attr[] = {
149 FM10K_TLV_ATTR_U32(FM10K_MAC_VLAN_MSG_VLAN),
150 FM10K_TLV_ATTR_BOOL(FM10K_MAC_VLAN_MSG_SET),
151 FM10K_TLV_ATTR_MAC_ADDR(FM10K_MAC_VLAN_MSG_MAC),
152 FM10K_TLV_ATTR_MAC_ADDR(FM10K_MAC_VLAN_MSG_DEFAULT_MAC),
153 FM10K_TLV_ATTR_MAC_ADDR(FM10K_MAC_VLAN_MSG_MULTICAST),
154 FM10K_TLV_ATTR_LAST
155 };
156
157 /**
158 * fm10k_update_vlan_vf - Update status of VLAN ID in VLAN filter table
159 * @hw: pointer to hardware structure
160 * @vid: VLAN ID to add to table
161 * @vsi: Reserved, should always be 0
162 * @set: Indicates if this is a set or clear operation
163 *
164 * This function adds or removes the corresponding VLAN ID from the VLAN
165 * filter table for this VF.
166 **/
fm10k_update_vlan_vf(struct fm10k_hw * hw,u32 vid,u8 vsi,bool set)167 static s32 fm10k_update_vlan_vf(struct fm10k_hw *hw, u32 vid, u8 vsi, bool set)
168 {
169 struct fm10k_mbx_info *mbx = &hw->mbx;
170 u32 msg[4];
171
172 /* verify the index is not set */
173 if (vsi)
174 return FM10K_ERR_PARAM;
175
176 /* clever trick to verify reserved bits in both vid and length */
177 if ((vid << 16 | vid) >> 28)
178 return FM10K_ERR_PARAM;
179
180 /* encode set bit into the VLAN ID */
181 if (!set)
182 vid |= FM10K_VLAN_CLEAR;
183
184 /* generate VLAN request */
185 fm10k_tlv_msg_init(msg, FM10K_VF_MSG_ID_MAC_VLAN);
186 fm10k_tlv_attr_put_u32(msg, FM10K_MAC_VLAN_MSG_VLAN, vid);
187
188 /* load onto outgoing mailbox */
189 return mbx->ops.enqueue_tx(hw, mbx, msg);
190 }
191
192 /**
193 * fm10k_msg_mac_vlan_vf - Read device MAC address from mailbox message
194 * @hw: pointer to the HW structure
195 * @results: Attributes for message
196 * @mbx: unused mailbox data
197 *
198 * This function should determine the MAC address for the VF
199 **/
fm10k_msg_mac_vlan_vf(struct fm10k_hw * hw,u32 ** results,struct fm10k_mbx_info __always_unused * mbx)200 s32 fm10k_msg_mac_vlan_vf(struct fm10k_hw *hw, u32 **results,
201 struct fm10k_mbx_info __always_unused *mbx)
202 {
203 u8 perm_addr[ETH_ALEN];
204 u16 vid;
205 s32 err;
206
207 /* record MAC address requested */
208 err = fm10k_tlv_attr_get_mac_vlan(
209 results[FM10K_MAC_VLAN_MSG_DEFAULT_MAC],
210 perm_addr, &vid);
211 if (err)
212 return err;
213
214 ether_addr_copy(hw->mac.perm_addr, perm_addr);
215 hw->mac.default_vid = vid & (FM10K_VLAN_TABLE_VID_MAX - 1);
216 hw->mac.vlan_override = !!(vid & FM10K_VLAN_OVERRIDE);
217
218 return 0;
219 }
220
221 /**
222 * fm10k_read_mac_addr_vf - Read device MAC address
223 * @hw: pointer to the HW structure
224 *
225 * This function should determine the MAC address for the VF
226 **/
fm10k_read_mac_addr_vf(struct fm10k_hw * hw)227 static s32 fm10k_read_mac_addr_vf(struct fm10k_hw *hw)
228 {
229 u8 perm_addr[ETH_ALEN];
230 u32 base_addr;
231
232 base_addr = fm10k_read_reg(hw, FM10K_TDBAL(0));
233
234 /* last byte should be 0 */
235 if (base_addr << 24)
236 return FM10K_ERR_INVALID_MAC_ADDR;
237
238 perm_addr[3] = (u8)(base_addr >> 24);
239 perm_addr[4] = (u8)(base_addr >> 16);
240 perm_addr[5] = (u8)(base_addr >> 8);
241
242 base_addr = fm10k_read_reg(hw, FM10K_TDBAH(0));
243
244 /* first byte should be all 1's */
245 if ((~base_addr) >> 24)
246 return FM10K_ERR_INVALID_MAC_ADDR;
247
248 perm_addr[0] = (u8)(base_addr >> 16);
249 perm_addr[1] = (u8)(base_addr >> 8);
250 perm_addr[2] = (u8)(base_addr);
251
252 ether_addr_copy(hw->mac.perm_addr, perm_addr);
253 ether_addr_copy(hw->mac.addr, perm_addr);
254
255 return 0;
256 }
257
258 /**
259 * fm10k_update_uc_addr_vf - Update device unicast addresses
260 * @hw: pointer to the HW structure
261 * @glort: unused
262 * @mac: MAC address to add/remove from table
263 * @vid: VLAN ID to add/remove from table
264 * @add: Indicates if this is an add or remove operation
265 * @flags: flags field to indicate add and secure - unused
266 *
267 * This function is used to add or remove unicast MAC addresses for
268 * the VF.
269 **/
fm10k_update_uc_addr_vf(struct fm10k_hw * hw,u16 __always_unused glort,const u8 * mac,u16 vid,bool add,u8 __always_unused flags)270 static s32 fm10k_update_uc_addr_vf(struct fm10k_hw *hw,
271 u16 __always_unused glort,
272 const u8 *mac, u16 vid, bool add,
273 u8 __always_unused flags)
274 {
275 struct fm10k_mbx_info *mbx = &hw->mbx;
276 u32 msg[7];
277
278 /* verify VLAN ID is valid */
279 if (vid >= FM10K_VLAN_TABLE_VID_MAX)
280 return FM10K_ERR_PARAM;
281
282 /* verify MAC address is valid */
283 if (!is_valid_ether_addr(mac))
284 return FM10K_ERR_PARAM;
285
286 /* verify we are not locked down on the MAC address */
287 if (is_valid_ether_addr(hw->mac.perm_addr) &&
288 !ether_addr_equal(hw->mac.perm_addr, mac))
289 return FM10K_ERR_PARAM;
290
291 /* add bit to notify us if this is a set or clear operation */
292 if (!add)
293 vid |= FM10K_VLAN_CLEAR;
294
295 /* generate VLAN request */
296 fm10k_tlv_msg_init(msg, FM10K_VF_MSG_ID_MAC_VLAN);
297 fm10k_tlv_attr_put_mac_vlan(msg, FM10K_MAC_VLAN_MSG_MAC, mac, vid);
298
299 /* load onto outgoing mailbox */
300 return mbx->ops.enqueue_tx(hw, mbx, msg);
301 }
302
303 /**
304 * fm10k_update_mc_addr_vf - Update device multicast addresses
305 * @hw: pointer to the HW structure
306 * @glort: unused
307 * @mac: MAC address to add/remove from table
308 * @vid: VLAN ID to add/remove from table
309 * @add: Indicates if this is an add or remove operation
310 *
311 * This function is used to add or remove multicast MAC addresses for
312 * the VF.
313 **/
fm10k_update_mc_addr_vf(struct fm10k_hw * hw,u16 __always_unused glort,const u8 * mac,u16 vid,bool add)314 static s32 fm10k_update_mc_addr_vf(struct fm10k_hw *hw,
315 u16 __always_unused glort,
316 const u8 *mac, u16 vid, bool add)
317 {
318 struct fm10k_mbx_info *mbx = &hw->mbx;
319 u32 msg[7];
320
321 /* verify VLAN ID is valid */
322 if (vid >= FM10K_VLAN_TABLE_VID_MAX)
323 return FM10K_ERR_PARAM;
324
325 /* verify multicast address is valid */
326 if (!is_multicast_ether_addr(mac))
327 return FM10K_ERR_PARAM;
328
329 /* add bit to notify us if this is a set or clear operation */
330 if (!add)
331 vid |= FM10K_VLAN_CLEAR;
332
333 /* generate VLAN request */
334 fm10k_tlv_msg_init(msg, FM10K_VF_MSG_ID_MAC_VLAN);
335 fm10k_tlv_attr_put_mac_vlan(msg, FM10K_MAC_VLAN_MSG_MULTICAST,
336 mac, vid);
337
338 /* load onto outgoing mailbox */
339 return mbx->ops.enqueue_tx(hw, mbx, msg);
340 }
341
342 /**
343 * fm10k_update_int_moderator_vf - Request update of interrupt moderator list
344 * @hw: pointer to hardware structure
345 *
346 * This function will issue a request to the PF to rescan our MSI-X table
347 * and to update the interrupt moderator linked list.
348 **/
fm10k_update_int_moderator_vf(struct fm10k_hw * hw)349 static void fm10k_update_int_moderator_vf(struct fm10k_hw *hw)
350 {
351 struct fm10k_mbx_info *mbx = &hw->mbx;
352 u32 msg[1];
353
354 /* generate MSI-X request */
355 fm10k_tlv_msg_init(msg, FM10K_VF_MSG_ID_MSIX);
356
357 /* load onto outgoing mailbox */
358 mbx->ops.enqueue_tx(hw, mbx, msg);
359 }
360
361 /* This structure defines the attibutes to be parsed below */
362 const struct fm10k_tlv_attr fm10k_lport_state_msg_attr[] = {
363 FM10K_TLV_ATTR_BOOL(FM10K_LPORT_STATE_MSG_DISABLE),
364 FM10K_TLV_ATTR_U8(FM10K_LPORT_STATE_MSG_XCAST_MODE),
365 FM10K_TLV_ATTR_BOOL(FM10K_LPORT_STATE_MSG_READY),
366 FM10K_TLV_ATTR_LAST
367 };
368
369 /**
370 * fm10k_msg_lport_state_vf - Message handler for lport_state message from PF
371 * @hw: Pointer to hardware structure
372 * @results: pointer array containing parsed data
373 * @mbx: Pointer to mailbox information structure
374 *
375 * This handler is meant to capture the indication from the PF that we
376 * are ready to bring up the interface.
377 **/
fm10k_msg_lport_state_vf(struct fm10k_hw * hw,u32 ** results,struct fm10k_mbx_info __always_unused * mbx)378 s32 fm10k_msg_lport_state_vf(struct fm10k_hw *hw, u32 **results,
379 struct fm10k_mbx_info __always_unused *mbx)
380 {
381 hw->mac.dglort_map = !results[FM10K_LPORT_STATE_MSG_READY] ?
382 FM10K_DGLORTMAP_NONE : FM10K_DGLORTMAP_ZERO;
383
384 return 0;
385 }
386
387 /**
388 * fm10k_update_lport_state_vf - Update device state in lower device
389 * @hw: pointer to the HW structure
390 * @glort: unused
391 * @count: number of logical ports to enable - unused (always 1)
392 * @enable: boolean value indicating if this is an enable or disable request
393 *
394 * Notify the lower device of a state change. If the lower device is
395 * enabled we can add filters, if it is disabled all filters for this
396 * logical port are flushed.
397 **/
fm10k_update_lport_state_vf(struct fm10k_hw * hw,u16 __always_unused glort,u16 __always_unused count,bool enable)398 static s32 fm10k_update_lport_state_vf(struct fm10k_hw *hw,
399 u16 __always_unused glort,
400 u16 __always_unused count, bool enable)
401 {
402 struct fm10k_mbx_info *mbx = &hw->mbx;
403 u32 msg[2];
404
405 /* reset glort mask 0 as we have to wait to be enabled */
406 hw->mac.dglort_map = FM10K_DGLORTMAP_NONE;
407
408 /* generate port state request */
409 fm10k_tlv_msg_init(msg, FM10K_VF_MSG_ID_LPORT_STATE);
410 if (!enable)
411 fm10k_tlv_attr_put_bool(msg, FM10K_LPORT_STATE_MSG_DISABLE);
412
413 /* load onto outgoing mailbox */
414 return mbx->ops.enqueue_tx(hw, mbx, msg);
415 }
416
417 /**
418 * fm10k_update_xcast_mode_vf - Request update of multicast mode
419 * @hw: pointer to hardware structure
420 * @glort: unused
421 * @mode: integer value indicating mode being requested
422 *
423 * This function will attempt to request a higher mode for the port
424 * so that it can enable either multicast, multicast promiscuous, or
425 * promiscuous mode of operation.
426 **/
fm10k_update_xcast_mode_vf(struct fm10k_hw * hw,u16 __always_unused glort,u8 mode)427 static s32 fm10k_update_xcast_mode_vf(struct fm10k_hw *hw,
428 u16 __always_unused glort, u8 mode)
429 {
430 struct fm10k_mbx_info *mbx = &hw->mbx;
431 u32 msg[3];
432
433 if (mode > FM10K_XCAST_MODE_NONE)
434 return FM10K_ERR_PARAM;
435
436 /* generate message requesting to change xcast mode */
437 fm10k_tlv_msg_init(msg, FM10K_VF_MSG_ID_LPORT_STATE);
438 fm10k_tlv_attr_put_u8(msg, FM10K_LPORT_STATE_MSG_XCAST_MODE, mode);
439
440 /* load onto outgoing mailbox */
441 return mbx->ops.enqueue_tx(hw, mbx, msg);
442 }
443
444 /**
445 * fm10k_update_hw_stats_vf - Updates hardware related statistics of VF
446 * @hw: pointer to hardware structure
447 * @stats: pointer to statistics structure
448 *
449 * This function collects and aggregates per queue hardware statistics.
450 **/
fm10k_update_hw_stats_vf(struct fm10k_hw * hw,struct fm10k_hw_stats * stats)451 static void fm10k_update_hw_stats_vf(struct fm10k_hw *hw,
452 struct fm10k_hw_stats *stats)
453 {
454 fm10k_update_hw_stats_q(hw, stats->q, 0, hw->mac.max_queues);
455 }
456
457 /**
458 * fm10k_rebind_hw_stats_vf - Resets base for hardware statistics of VF
459 * @hw: pointer to hardware structure
460 * @stats: pointer to the stats structure to update
461 *
462 * This function resets the base for queue hardware statistics.
463 **/
fm10k_rebind_hw_stats_vf(struct fm10k_hw * hw,struct fm10k_hw_stats * stats)464 static void fm10k_rebind_hw_stats_vf(struct fm10k_hw *hw,
465 struct fm10k_hw_stats *stats)
466 {
467 /* Unbind Queue Statistics */
468 fm10k_unbind_hw_stats_q(stats->q, 0, hw->mac.max_queues);
469
470 /* Reinitialize bases for all stats */
471 fm10k_update_hw_stats_vf(hw, stats);
472 }
473
474 /**
475 * fm10k_configure_dglort_map_vf - Configures GLORT entry and queues
476 * @hw: pointer to hardware structure
477 * @dglort: pointer to dglort configuration structure
478 *
479 * Reads the configuration structure contained in dglort_cfg and uses
480 * that information to then populate a DGLORTMAP/DEC entry and the queues
481 * to which it has been assigned.
482 **/
fm10k_configure_dglort_map_vf(struct fm10k_hw __always_unused * hw,struct fm10k_dglort_cfg * dglort)483 static s32 fm10k_configure_dglort_map_vf(struct fm10k_hw __always_unused *hw,
484 struct fm10k_dglort_cfg *dglort)
485 {
486 /* verify the dglort pointer */
487 if (!dglort)
488 return FM10K_ERR_PARAM;
489
490 /* stub for now until we determine correct message for this */
491
492 return 0;
493 }
494
495 static const struct fm10k_msg_data fm10k_msg_data_vf[] = {
496 FM10K_TLV_MSG_TEST_HANDLER(fm10k_tlv_msg_test),
497 FM10K_VF_MSG_MAC_VLAN_HANDLER(fm10k_msg_mac_vlan_vf),
498 FM10K_VF_MSG_LPORT_STATE_HANDLER(fm10k_msg_lport_state_vf),
499 FM10K_TLV_MSG_ERROR_HANDLER(fm10k_tlv_msg_error),
500 };
501
502 static const struct fm10k_mac_ops mac_ops_vf = {
503 .get_bus_info = fm10k_get_bus_info_generic,
504 .reset_hw = fm10k_reset_hw_vf,
505 .init_hw = fm10k_init_hw_vf,
506 .start_hw = fm10k_start_hw_generic,
507 .stop_hw = fm10k_stop_hw_vf,
508 .update_vlan = fm10k_update_vlan_vf,
509 .read_mac_addr = fm10k_read_mac_addr_vf,
510 .update_uc_addr = fm10k_update_uc_addr_vf,
511 .update_mc_addr = fm10k_update_mc_addr_vf,
512 .update_xcast_mode = fm10k_update_xcast_mode_vf,
513 .update_int_moderator = fm10k_update_int_moderator_vf,
514 .update_lport_state = fm10k_update_lport_state_vf,
515 .update_hw_stats = fm10k_update_hw_stats_vf,
516 .rebind_hw_stats = fm10k_rebind_hw_stats_vf,
517 .configure_dglort_map = fm10k_configure_dglort_map_vf,
518 .get_host_state = fm10k_get_host_state_generic,
519 };
520
fm10k_get_invariants_vf(struct fm10k_hw * hw)521 static s32 fm10k_get_invariants_vf(struct fm10k_hw *hw)
522 {
523 fm10k_get_invariants_generic(hw);
524
525 return fm10k_pfvf_mbx_init(hw, &hw->mbx, fm10k_msg_data_vf, 0);
526 }
527
528 const struct fm10k_info fm10k_vf_info = {
529 .mac = fm10k_mac_vf,
530 .get_invariants = fm10k_get_invariants_vf,
531 .mac_ops = &mac_ops_vf,
532 };
533