1* Marvell EBU GPIO controller
2
3Required properties:
4
5- compatible : Should be "marvell,orion-gpio", "marvell,mv78200-gpio",
6  "marvell,armadaxp-gpio" or "marvell,armada-8k-gpio".
7
8    "marvell,orion-gpio" should be used for Orion, Kirkwood, Dove,
9    Discovery (except MV78200) and Armada 370. "marvell,mv78200-gpio"
10    should be used for the Discovery MV78200.
11
12    "marvel,armadaxp-gpio" should be used for all Armada XP SoCs
13    (MV78230, MV78260, MV78460).
14
15    "marvell,armada-8k-gpio" should be used for the Armada 7K and 8K
16    SoCs (either from AP or CP), see
17    Documentation/devicetree/bindings/arm/marvell/ap80x-system-controller.txt
18    for specific details about the offset property.
19
20- reg: Address and length of the register set for the device. Only one
21  entry is expected, except for the "marvell,armadaxp-gpio" variant
22  for which two entries are expected: one for the general registers,
23  one for the per-cpu registers. Not used for marvell,armada-8k-gpio.
24
25- interrupts: The list of interrupts that are used for all the pins
26  managed by this GPIO bank. There can be more than one interrupt
27  (example: 1 interrupt per 8 pins on Armada XP, which means 4
28  interrupts per bank of 32 GPIOs).
29
30- interrupt-controller: identifies the node as an interrupt controller
31
32- #interrupt-cells: specifies the number of cells needed to encode an
33  interrupt source. Should be two.
34  The first cell is the GPIO number.
35  The second cell is used to specify flags:
36    bits[3:0] trigger type and level flags:
37      1 = low-to-high edge triggered.
38      2 = high-to-low edge triggered.
39      4 = active high level-sensitive.
40      8 = active low level-sensitive.
41
42- gpio-controller: marks the device node as a gpio controller
43
44- ngpios: number of GPIOs this controller has
45
46- #gpio-cells: Should be two. The first cell is the pin number. The
47  second cell is reserved for flags, unused at the moment.
48
49Optional properties:
50
51In order to use the GPIO lines in PWM mode, some additional optional
52properties are required.
53
54- compatible: Must contain "marvell,armada-370-gpio"
55
56- reg: an additional register set is needed, for the GPIO Blink
57  Counter on/off registers.
58
59- reg-names: Must contain an entry "pwm" corresponding to the
60  additional register range needed for PWM operation.
61
62- #pwm-cells: Should be two. The first cell is the GPIO line number. The
63  second cell is the period in nanoseconds.
64
65- clocks: Must be a phandle to the clock for the GPIO controller.
66
67Example:
68
69		gpio0: gpio@d0018100 {
70			compatible = "marvell,armadaxp-gpio";
71			reg = <0xd0018100 0x40>,
72			    <0xd0018800 0x30>;
73			ngpios = <32>;
74			gpio-controller;
75			#gpio-cells = <2>;
76			interrupt-controller;
77			#interrupt-cells = <2>;
78			interrupts = <16>, <17>, <18>, <19>;
79		};
80
81		gpio1: gpio@18140 {
82			compatible = "marvell,armada-370-gpio";
83			reg = <0x18140 0x40>, <0x181c8 0x08>;
84			reg-names = "gpio", "pwm";
85			ngpios = <17>;
86			gpio-controller;
87			#gpio-cells = <2>;
88			#pwm-cells = <2>;
89			interrupt-controller;
90			#interrupt-cells = <2>;
91			interrupts = <87>, <88>, <89>;
92			clocks = <&coreclk 0>;
93		};
94