1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright 2018-2020 NXP 4 */ 5 6 #ifndef __LX2_COMMON_H 7 #define __LX2_COMMON_H 8 9 #include <asm/arch/stream_id_lsch3.h> 10 #include <asm/arch/config.h> 11 #include <asm/arch/soc.h> 12 13 #define CONFIG_REMAKE_ELF 14 #define CONFIG_FSL_LAYERSCAPE 15 #define CONFIG_GICV3 16 #define CONFIG_FSL_TZPC_BP147 17 #define CONFIG_FSL_MEMAC 18 19 #define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE 20 #define CONFIG_SYS_FLASH_BASE 0x20000000 21 22 #define CONFIG_SKIP_LOWLEVEL_INIT 23 24 /* DDR */ 25 #define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */ 26 #define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */ 27 #define CONFIG_VERY_BIG_RAM 28 #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL 29 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 30 #define CONFIG_SYS_DDR_BLOCK2_BASE 0x2080000000ULL 31 #define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2 32 #define CONFIG_SYS_SDRAM_SIZE 0x200000000UL 33 #define CONFIG_DDR_SPD 34 #define CONFIG_DDR_ECC 35 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 36 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 37 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 38 #define SPD_EEPROM_ADDRESS1 0x51 39 #define SPD_EEPROM_ADDRESS2 0x52 40 #define SPD_EEPROM_ADDRESS3 0x53 41 #define SPD_EEPROM_ADDRESS4 0x54 42 #define SPD_EEPROM_ADDRESS5 0x55 43 #define SPD_EEPROM_ADDRESS6 0x56 44 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 45 #define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */ 46 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 47 #define CONFIG_CHIP_SELECTS_PER_CTRL 4 48 #define CONFIG_FSL_DDR_BIST /* enable built-in memory test */ 49 #define CONFIG_SYS_MONITOR_LEN (936 * 1024) 50 51 /* Miscellaneous configurable options */ 52 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000) 53 54 /* SMP Definitinos */ 55 #define CPU_RELEASE_ADDR secondary_boot_addr 56 57 /* Generic Timer Definitions */ 58 /* 59 * This is not an accurate number. It is used in start.S. The frequency 60 * will be udpated later when get_bus_freq(0) is available. 61 */ 62 63 #define COUNTER_FREQUENCY 25000000 /* 25MHz */ 64 65 /* Size of malloc() pool */ 66 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024) 67 68 /* Serial Port */ 69 #define CONFIG_PL01X_SERIAL 70 #define CONFIG_PL011_CLOCK (get_bus_freq(0) / 4) 71 #define CONFIG_SYS_SERIAL0 0x21c0000 72 #define CONFIG_SYS_SERIAL1 0x21d0000 73 #define CONFIG_SYS_SERIAL2 0x21e0000 74 #define CONFIG_SYS_SERIAL3 0x21f0000 75 /*below might needs to be removed*/ 76 #define CONFIG_PL01x_PORTS {(void *)CONFIG_SYS_SERIAL0, \ 77 (void *)CONFIG_SYS_SERIAL1, \ 78 (void *)CONFIG_SYS_SERIAL2, \ 79 (void *)CONFIG_SYS_SERIAL3 } 80 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } 81 82 /* MC firmware */ 83 #define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000 84 #define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000 85 #define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000 86 #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000 87 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 88 89 /* Define phy_reset function to boot the MC based on mcinitcmd. 90 * This happens late enough to properly fixup u-boot env MAC addresses. 91 */ 92 #define CONFIG_RESET_PHY_R 93 94 /* 95 * Carve out a DDR region which will not be used by u-boot/Linux 96 * 97 * It will be used by MC and Debug Server. The MC region must be 98 * 512MB aligned, so the min size to hide is 512MB. 99 */ 100 #ifdef CONFIG_FSL_MC_ENET 101 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (256UL * 1024 * 1024) 102 #endif 103 104 /* I2C bus multiplexer */ 105 #define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/ 106 #define I2C_MUX_CH_DEFAULT 0x8 107 108 /* RTC */ 109 #define RTC 110 #define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/ 111 112 /* EEPROM */ 113 #define CONFIG_ID_EEPROM 114 #define CONFIG_SYS_I2C_EEPROM_NXID 115 #define CONFIG_SYS_EEPROM_BUS_NUM 0 116 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 117 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 118 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 119 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 120 121 /* Qixis */ 122 #define CONFIG_FSL_QIXIS 123 #define CONFIG_QIXIS_I2C_ACCESS 124 #define CONFIG_SYS_I2C_FPGA_ADDR 0x66 125 126 /* PCI */ 127 #ifdef CONFIG_PCI 128 #define CONFIG_SYS_PCI_64BIT 129 #define CONFIG_PCI_SCAN_SHOW 130 #endif 131 132 /* MMC */ 133 #ifdef CONFIG_MMC 134 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 135 #endif 136 137 /* SATA */ 138 139 #ifdef CONFIG_SCSI 140 #define CONFIG_SCSI_AHCI_PLAT 141 #define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1 142 #define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2 143 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 144 #define CONFIG_SYS_SCSI_MAX_LUN 1 145 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ 146 CONFIG_SYS_SCSI_MAX_LUN) 147 #endif 148 149 /* USB */ 150 #ifdef CONFIG_USB 151 #define CONFIG_HAS_FSL_XHCI_USB 152 #ifndef CONFIG_TARGET_LX2162AQDS 153 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 154 #endif 155 #endif 156 157 /* GPIO */ 158 #ifdef CONFIG_DM_GPIO 159 #ifndef CONFIG_MPC8XXX_GPIO 160 #define CONFIG_MPC8XXX_GPIO 161 #endif 162 #endif 163 164 #ifndef __ASSEMBLY__ 165 unsigned long get_board_sys_clk(void); 166 unsigned long get_board_ddr_clk(void); 167 #endif 168 169 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() 170 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() 171 #define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ / 4) 172 173 #define CONFIG_HWCONFIG 174 #define HWCONFIG_BUFFER_SIZE 128 175 176 /* Monitor Command Prompt */ 177 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 178 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ 179 sizeof(CONFIG_SYS_PROMPT) + 16) 180 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */ 181 #define CONFIG_SYS_MAXARGS 64 /* max command args */ 182 183 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 184 185 /* Initial environment variables */ 186 #define XSPI_MC_INIT_CMD \ 187 "sf probe 0:0 && " \ 188 "sf read 0x80640000 0x640000 0x80000 && " \ 189 "env exists secureboot && " \ 190 "esbc_validate 0x80640000 && " \ 191 "esbc_validate 0x80680000; " \ 192 "sf read 0x80a00000 0xa00000 0x300000 && " \ 193 "sf read 0x80e00000 0xe00000 0x100000; " \ 194 "fsl_mc start mc 0x80a00000 0x80e00000\0" 195 196 #define SD_MC_INIT_CMD \ 197 "mmc read 0x80a00000 0x5000 0x1200;" \ 198 "mmc read 0x80e00000 0x7000 0x800;" \ 199 "env exists secureboot && " \ 200 "mmc read 0x80640000 0x3200 0x20 && " \ 201 "mmc read 0x80680000 0x3400 0x20 && " \ 202 "esbc_validate 0x80640000 && " \ 203 "esbc_validate 0x80680000 ;" \ 204 "fsl_mc start mc 0x80a00000 0x80e00000\0" 205 206 #define SD2_MC_INIT_CMD \ 207 "mmc dev 1; mmc read 0x80a00000 0x5000 0x1200;" \ 208 "mmc read 0x80e00000 0x7000 0x800;" \ 209 "env exists secureboot && " \ 210 "mmc read 0x80640000 0x3200 0x20 && " \ 211 "mmc read 0x80680000 0x3400 0x20 && " \ 212 "esbc_validate 0x80640000 && " \ 213 "esbc_validate 0x80680000 ;" \ 214 "fsl_mc start mc 0x80a00000 0x80e00000\0" 215 216 #define EXTRA_ENV_SETTINGS \ 217 "hwconfig=fsl_ddr:bank_intlv=auto\0" \ 218 "ramdisk_addr=0x800000\0" \ 219 "ramdisk_size=0x2000000\0" \ 220 "fdt_high=0xa0000000\0" \ 221 "initrd_high=0xffffffffffffffff\0" \ 222 "fdt_addr=0x64f00000\0" \ 223 "kernel_start=0x1000000\0" \ 224 "kernelheader_start=0x600000\0" \ 225 "scriptaddr=0x80000000\0" \ 226 "scripthdraddr=0x80080000\0" \ 227 "fdtheader_addr_r=0x80100000\0" \ 228 "kernelheader_addr_r=0x80200000\0" \ 229 "kernel_addr_r=0x81000000\0" \ 230 "kernelheader_size=0x40000\0" \ 231 "fdt_addr_r=0x90000000\0" \ 232 "load_addr=0xa0000000\0" \ 233 "kernel_size=0x2800000\0" \ 234 "kernel_addr_sd=0x8000\0" \ 235 "kernelhdr_addr_sd=0x3000\0" \ 236 "kernel_size_sd=0x14000\0" \ 237 "kernelhdr_size_sd=0x20\0" \ 238 "console=ttyAMA0,38400n8\0" \ 239 BOOTENV \ 240 "mcmemsize=0x70000000\0" \ 241 XSPI_MC_INIT_CMD \ 242 "scan_dev_for_boot_part=" \ 243 "part list ${devtype} ${devnum} devplist; " \ 244 "env exists devplist || setenv devplist 1; " \ 245 "for distro_bootpart in ${devplist}; do " \ 246 "if fstype ${devtype} " \ 247 "${devnum}:${distro_bootpart} " \ 248 "bootfstype; then " \ 249 "run scan_dev_for_boot; " \ 250 "fi; " \ 251 "done\0" \ 252 "boot_a_script=" \ 253 "load ${devtype} ${devnum}:${distro_bootpart} " \ 254 "${scriptaddr} ${prefix}${script}; " \ 255 "env exists secureboot && load ${devtype} " \ 256 "${devnum}:${distro_bootpart} " \ 257 "${scripthdraddr} ${prefix}${boot_script_hdr} " \ 258 "&& esbc_validate ${scripthdraddr};" \ 259 "source ${scriptaddr}\0" 260 261 #define XSPI_NOR_BOOTCOMMAND \ 262 "sf probe 0:0; " \ 263 "sf read 0x806c0000 0x6c0000 0x40000; " \ 264 "env exists mcinitcmd && env exists secureboot" \ 265 " && esbc_validate 0x806c0000; " \ 266 "sf read 0x80d00000 0xd00000 0x100000; " \ 267 "env exists mcinitcmd && " \ 268 "fsl_mc lazyapply dpl 0x80d00000; " \ 269 "run distro_bootcmd;run xspi_bootcmd; " \ 270 "env exists secureboot && esbc_halt;" 271 272 #define SD_BOOTCOMMAND \ 273 "env exists mcinitcmd && mmcinfo; " \ 274 "mmc read 0x80d00000 0x6800 0x800; " \ 275 "env exists mcinitcmd && env exists secureboot " \ 276 " && mmc read 0x806C0000 0x3600 0x20 " \ 277 "&& esbc_validate 0x806C0000;env exists mcinitcmd " \ 278 "&& fsl_mc lazyapply dpl 0x80d00000;" \ 279 "run distro_bootcmd;run sd_bootcmd;" \ 280 "env exists secureboot && esbc_halt;" 281 282 #define SD2_BOOTCOMMAND \ 283 "mmc dev 1; env exists mcinitcmd && mmcinfo; " \ 284 "mmc read 0x80d00000 0x6800 0x800; " \ 285 "env exists mcinitcmd && env exists secureboot " \ 286 " && mmc read 0x806C0000 0x3600 0x20 " \ 287 "&& esbc_validate 0x806C0000;env exists mcinitcmd " \ 288 "&& fsl_mc lazyapply dpl 0x80d00000;" \ 289 "run distro_bootcmd;run sd2_bootcmd;" \ 290 "env exists secureboot && esbc_halt;" 291 292 #define BOOT_TARGET_DEVICES(func) \ 293 func(USB, usb, 0) \ 294 func(MMC, mmc, 0) \ 295 func(MMC, mmc, 1) \ 296 func(SCSI, scsi, 0) \ 297 func(DHCP, dhcp, na) 298 #include <config_distro_bootcmd.h> 299 300 #endif /* __LX2_COMMON_H */ 301