1// SPDX-License-Identifier: GPL-2.0-only 2/dts-v1/; 3 4#include <dt-bindings/input/input.h> 5#include "omap443x.dtsi" 6#include "motorola-cpcap-mapphone.dtsi" 7 8/ { 9 chosen { 10 stdout-path = &uart3; 11 }; 12 13 aliases { 14 display0 = &lcd0; 15 display1 = &hdmi0; 16 }; 17 18 /* 19 * We seem to have only 1021 MB accessible, 1021 - 1022 is locked, 20 * then 1023 - 1024 seems to contain mbm. 21 */ 22 memory { 23 device_type = "memory"; 24 reg = <0x80000000 0x3fd00000>; /* 1021 MB */ 25 }; 26 27 /* Poweroff GPIO probably connected to CPCAP */ 28 gpio-poweroff { 29 compatible = "gpio-poweroff"; 30 pinctrl-0 = <&poweroff_gpio>; 31 pinctrl-names = "default"; 32 gpios = <&gpio2 18 GPIO_ACTIVE_LOW>; /* gpio50 */ 33 }; 34 35 hdmi0: connector { 36 compatible = "hdmi-connector"; 37 pinctrl-0 = <&hdmi_hpd_gpio>; 38 pinctrl-names = "default"; 39 label = "hdmi"; 40 type = "d"; 41 42 hpd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; /* gpio63 */ 43 44 port { 45 hdmi_connector_in: endpoint { 46 remote-endpoint = <&hdmi_out>; 47 }; 48 }; 49 }; 50 51 /* 52 * HDMI 5V regulator probably sourced from battery. Let's keep 53 * keep this as always enabled for HDMI to work until we've 54 * figured what the encoder chip is. 55 */ 56 hdmi_regulator: regulator-hdmi { 57 compatible = "regulator-fixed"; 58 regulator-name = "hdmi"; 59 regulator-min-microvolt = <5000000>; 60 regulator-max-microvolt = <5000000>; 61 gpio = <&gpio2 27 GPIO_ACTIVE_HIGH>; /* gpio59 */ 62 enable-active-high; 63 regulator-always-on; 64 }; 65 66 /* FS USB Host PHY on port 1 for mdm6600 */ 67 fsusb1_phy: usb-phy@1 { 68 compatible = "motorola,mapphone-mdm6600"; 69 pinctrl-0 = <&usb_mdm6600_pins>; 70 pinctrl-names = "default"; 71 enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>; /* gpio_95 */ 72 power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* gpio_54 */ 73 reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>; /* gpio_49 */ 74 /* mode: gpio_148 gpio_149 */ 75 motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>, 76 <&gpio5 21 GPIO_ACTIVE_HIGH>; 77 /* cmd: gpio_103 gpio_104 gpio_142 */ 78 motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>, 79 <&gpio4 8 GPIO_ACTIVE_HIGH>, 80 <&gpio5 14 GPIO_ACTIVE_HIGH>; 81 /* status: gpio_52 gpio_53 gpio_55 */ 82 motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>, 83 <&gpio2 21 GPIO_ACTIVE_HIGH>, 84 <&gpio2 23 GPIO_ACTIVE_HIGH>; 85 #phy-cells = <0>; 86 }; 87 88 /* HS USB host TLL nop-phy on port 2 for w3glte */ 89 hsusb2_phy: usb-phy@2 { 90 compatible = "usb-nop-xceiv"; 91 #phy-cells = <0>; 92 }; 93 94 /* LCD regulator from sw5 source */ 95 lcd_regulator: regulator-lcd { 96 compatible = "regulator-fixed"; 97 regulator-name = "lcd"; 98 regulator-min-microvolt = <5050000>; 99 regulator-max-microvolt = <5050000>; 100 gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>; /* gpio96 */ 101 enable-active-high; 102 vin-supply = <&sw5>; 103 }; 104 105 /* This is probably coming straight from the battery.. */ 106 wl12xx_vmmc: regulator-wl12xx { 107 compatible = "regulator-fixed"; 108 regulator-name = "vwl1271"; 109 regulator-min-microvolt = <1650000>; 110 regulator-max-microvolt = <1650000>; 111 gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; /* gpio94 */ 112 startup-delay-us = <70000>; 113 enable-active-high; 114 }; 115 116 soundcard { 117 compatible = "audio-graph-card"; 118 label = "Mapphone Audio"; 119 120 widgets = 121 "Speaker", "Earpiece", 122 "Speaker", "Loudspeaker", 123 "Headphone", "Headphone Jack", 124 "Microphone", "Internal Mic"; 125 126 routing = 127 "Earpiece", "EP", 128 "Loudspeaker", "SPKR", 129 "Headphone Jack", "HSL", 130 "Headphone Jack", "HSR", 131 "MICR", "Internal Mic"; 132 133 dais = <&mcbsp2_port>, <&mcbsp3_port>; 134 }; 135 136 pwm8: dmtimer-pwm-8 { 137 pinctrl-names = "default"; 138 pinctrl-0 = <&vibrator_direction_pin>; 139 140 compatible = "ti,omap-dmtimer-pwm"; 141 #pwm-cells = <3>; 142 ti,timers = <&timer8>; 143 ti,clock-source = <0x01>; 144 }; 145 146 pwm9: dmtimer-pwm-9 { 147 pinctrl-names = "default"; 148 pinctrl-0 = <&vibrator_enable_pin>; 149 150 compatible = "ti,omap-dmtimer-pwm"; 151 #pwm-cells = <3>; 152 ti,timers = <&timer9>; 153 ti,clock-source = <0x01>; 154 }; 155 156 vibrator { 157 compatible = "pwm-vibrator"; 158 pwms = <&pwm9 0 10000000 0>, <&pwm8 0 10000000 0>; 159 pwm-names = "enable", "direction"; 160 direction-duty-cycle-ns = <10000000>; 161 }; 162 163 backlight: backlight { 164 compatible = "led-backlight"; 165 166 leds = <&backlight_led>; 167 brightness-levels = <31 63 95 127 159 191 223 255>; 168 default-brightness-level = <6>; 169 }; 170}; 171 172&cpu_thermal { 173 polling-delay = <10000>; /* milliseconds */ 174}; 175 176&cpu_alert0 { 177 temperature = <80000>; /* millicelsius */ 178}; 179 180&cpu0 { 181 /* 182 * Note that the 1.2GiHz mode is enabled for all SoC variants for 183 * the Motorola Android Linux v3.0.8 based kernel. 184 */ 185 operating-points = < 186 /* kHz uV */ 187 300000 1025000 188 600000 1200000 189 800000 1313000 190 1008000 1375000 191 1200000 1375000 192 >; 193}; 194 195&dss { 196 status = "okay"; 197}; 198 199&dsi1 { 200 status = "okay"; 201 vdd-supply = <&vcsi>; 202 203 port { 204 dsi1_out_ep: endpoint { 205 remote-endpoint = <&lcd0_in>; 206 lanes = <0 1 2 3 4 5>; 207 }; 208 }; 209 210 lcd0: panel@0 { 211 compatible = "motorola,droid4-panel", "panel-dsi-cm"; 212 reg = <0>; 213 label = "lcd0"; 214 vddi-supply = <&lcd_regulator>; 215 reset-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* gpio101 */ 216 217 backlight = <&backlight>; 218 219 width-mm = <50>; 220 height-mm = <89>; 221 rotation = <90>; 222 223 panel-timing { 224 clock-frequency = <0>; /* Calculated by dsi */ 225 226 hback-porch = <2>; 227 hactive = <540>; 228 hfront-porch = <0>; 229 hsync-len = <2>; 230 231 vback-porch = <1>; 232 vactive = <960>; 233 vfront-porch = <0>; 234 vsync-len = <1>; 235 236 hsync-active = <0>; 237 vsync-active = <0>; 238 de-active = <1>; 239 pixelclk-active = <1>; 240 }; 241 242 port { 243 lcd0_in: endpoint { 244 remote-endpoint = <&dsi1_out_ep>; 245 }; 246 }; 247 }; 248}; 249 250&hdmi { 251 status = "okay"; 252 pinctrl-0 = <&dss_hdmi_pins>; 253 pinctrl-names = "default"; 254 vdda-supply = <&vdac>; 255 256 port { 257 hdmi_out: endpoint { 258 remote-endpoint = <&hdmi_connector_in>; 259 lanes = <1 0 3 2 5 4 7 6>; 260 }; 261 }; 262}; 263 264/* Battery NVRAM on 1-wire handled by w1_ds250x driver */ 265&hdqw1w { 266 pinctrl-0 = <&hdq_pins>; 267 pinctrl-names = "default"; 268 ti,mode = "1w"; 269}; 270 271&i2c1 { 272 tmp105@48 { 273 compatible = "ti,tmp105"; 274 reg = <0x48>; 275 pinctrl-0 = <&tmp105_irq>; 276 pinctrl-names = "default"; 277 /* kpd_row0.gpio_178 */ 278 interrupts-extended = <&gpio6 18 IRQ_TYPE_EDGE_FALLING 279 &omap4_pmx_core 0x14e>; 280 interrupt-names = "irq", "wakeup"; 281 wakeup-source; 282 }; 283}; 284 285&mmc1 { 286 vmmc-supply = <&vwlan2>; 287 bus-width = <4>; 288 cd-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>; /* gpio176 */ 289}; 290 291&mmc2 { 292 vmmc-supply = <&vsdio>; 293 bus-width = <8>; 294 ti,non-removable; 295}; 296 297&mmc3 { 298 pinctrl-names = "default"; 299 pinctrl-0 = <&mmc3_pins>; 300 vmmc-supply = <&wl12xx_vmmc>; 301 /* uart2_tx.sdmmc3_dat1 pad as wakeirq */ 302 interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH 303 &omap4_pmx_core 0xde>; 304 interrupt-names = "irq", "wakeup"; 305 non-removable; 306 bus-width = <4>; 307 cap-power-off-card; 308 keep-power-in-suspend; 309 310 #address-cells = <1>; 311 #size-cells = <0>; 312 wlcore: wlcore@2 { 313 compatible = "ti,wl1285", "ti,wl1283"; 314 reg = <2>; 315 /* gpio_100 with gpmc_wait2 pad as wakeirq */ 316 interrupts-extended = <&gpio4 4 IRQ_TYPE_LEVEL_HIGH>, 317 <&omap4_pmx_core 0x4e>; 318 interrupt-names = "irq", "wakeup"; 319 ref-clock-frequency = <26000000>; 320 tcxo-clock-frequency = <26000000>; 321 }; 322}; 323 324&i2c2 { 325 touchscreen@4a { 326 compatible = "atmel,maxtouch"; 327 reg = <0x4a>; 328 pinctrl-names = "default"; 329 pinctrl-0 = <&touchscreen_pins>; 330 331 reset-gpios = <&gpio6 13 GPIO_ACTIVE_LOW>; /* gpio173 */ 332 333 /* gpio_183 with sys_nirq2 pad as wakeup */ 334 interrupts-extended = <&gpio6 23 IRQ_TYPE_LEVEL_LOW>, 335 <&omap4_pmx_core 0x160>; 336 interrupt-names = "irq", "wakeup"; 337 wakeup-source; 338 }; 339 340 isl29030@44 { 341 compatible = "isil,isl29030"; 342 reg = <0x44>; 343 344 pinctrl-names = "default"; 345 pinctrl-0 = <&als_proximity_pins>; 346 347 interrupt-parent = <&gpio6>; 348 interrupts = <17 IRQ_TYPE_LEVEL_LOW>; /* gpio177 */ 349 }; 350}; 351 352&omap4_pmx_core { 353 354 /* hdmi_hpd.gpio_63 */ 355 hdmi_hpd_gpio: pinmux_hdmi_hpd_pins { 356 pinctrl-single,pins = < 357 OMAP4_IOPAD(0x098, PIN_INPUT | MUX_MODE3) 358 >; 359 }; 360 361 hdq_pins: pinmux_hdq_pins { 362 pinctrl-single,pins = < 363 /* 0x4a100120 hdq_sio.hdq_sio aa27 */ 364 OMAP4_IOPAD(0x120, PIN_INPUT | MUX_MODE0) 365 >; 366 }; 367 368 /* hdmi_cec.hdmi_cec, hdmi_scl.hdmi_scl, hdmi_sda.hdmi_sda */ 369 dss_hdmi_pins: pinmux_dss_hdmi_pins { 370 pinctrl-single,pins = < 371 OMAP4_IOPAD(0x09a, PIN_INPUT | MUX_MODE0) 372 OMAP4_IOPAD(0x09c, PIN_INPUT | MUX_MODE0) 373 OMAP4_IOPAD(0x09e, PIN_INPUT | MUX_MODE0) 374 >; 375 }; 376 377 /* 378 * Android uses PIN_OFF_INPUT_PULLDOWN | PIN_INPUT_PULLUP | MUX_MODE3 379 * for gpio_100, but the internal pull makes wlan flakey on some 380 * devices. Off mode value should be tested if we have off mode working 381 * later on. 382 */ 383 mmc3_pins: pinmux_mmc3_pins { 384 pinctrl-single,pins = < 385 /* 0x4a10008e gpmc_wait2.gpio_100 d23 */ 386 OMAP4_IOPAD(0x08e, PIN_INPUT | MUX_MODE3) 387 388 /* 0x4a100102 abe_mcbsp1_dx.sdmmc3_dat2 ab25 */ 389 OMAP4_IOPAD(0x102, PIN_INPUT_PULLUP | MUX_MODE1) 390 391 /* 0x4a100104 abe_mcbsp1_fsx.sdmmc3_dat3 ac27 */ 392 OMAP4_IOPAD(0x104, PIN_INPUT_PULLUP | MUX_MODE1) 393 394 /* 0x4a100118 uart2_cts.sdmmc3_clk ab26 */ 395 OMAP4_IOPAD(0x118, PIN_INPUT | MUX_MODE1) 396 397 /* 0x4a10011a uart2_rts.sdmmc3_cmd ab27 */ 398 OMAP4_IOPAD(0x11a, PIN_INPUT_PULLUP | MUX_MODE1) 399 400 /* 0x4a10011c uart2_rx.sdmmc3_dat0 aa25 */ 401 OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE1) 402 403 /* 0x4a10011e uart2_tx.sdmmc3_dat1 aa26 */ 404 OMAP4_IOPAD(0x11e, PIN_INPUT_PULLUP | MUX_MODE1) 405 >; 406 }; 407 408 /* gpmc_ncs0.gpio_50 */ 409 poweroff_gpio: pinmux_poweroff_pins { 410 pinctrl-single,pins = < 411 OMAP4_IOPAD(0x074, PIN_OUTPUT_PULLUP | MUX_MODE3) 412 >; 413 }; 414 415 /* kpd_row0.gpio_178 */ 416 tmp105_irq: pinmux_tmp105_irq { 417 pinctrl-single,pins = < 418 OMAP4_IOPAD(0x18e, PIN_INPUT_PULLUP | MUX_MODE3) 419 >; 420 }; 421 422 usb_gpio_mux_sel1: pinmux_usb_gpio_mux_sel1_pins { 423 /* gpio_60 */ 424 pinctrl-single,pins = < 425 OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3) 426 >; 427 }; 428 429 touchscreen_pins: pinmux_touchscreen_pins { 430 pinctrl-single,pins = < 431 OMAP4_IOPAD(0x180, PIN_OUTPUT | MUX_MODE3) 432 OMAP4_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE3) 433 >; 434 }; 435 436 als_proximity_pins: pinmux_als_proximity_pins { 437 pinctrl-single,pins = < 438 OMAP4_IOPAD(0x18c, PIN_INPUT_PULLUP | MUX_MODE3) 439 >; 440 }; 441 442 usb_mdm6600_pins: pinmux_usb_mdm6600_pins { 443 pinctrl-single,pins = < 444 /* enable 0x4a1000d8 usbb1_ulpitll_dat7.gpio_95 ag16 */ 445 OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3) 446 447 /* power 0x4a10007c gpmc_nwp.gpio_54 c25 */ 448 OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3) 449 450 /* reset 0x4a100072 gpmc_a25.gpio_49 d20 */ 451 OMAP4_IOPAD(0x072, PIN_OUTPUT | MUX_MODE3) 452 453 /* mode0/bpwake 0x4a10014e sdmmc5_dat1.gpio_148 af4 */ 454 OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3) 455 456 /* mode1/apwake 0x4a100150 sdmmc5_dat2.gpio_149 ag3 */ 457 OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3) 458 459 /* status0 0x4a10007e gpmc_clk.gpio_55 b22 */ 460 OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3) 461 462 /* status1 0x4a10007a gpmc_ncs3.gpio_53 c22 */ 463 OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3) 464 465 /* status2 0x4a100078 gpmc_ncs2.gpio_52 d21 */ 466 OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3) 467 468 /* cmd0 0x4a100094 gpmc_ncs6.gpio_103 c24 */ 469 OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3) 470 471 /* cmd1 0x4a100096 gpmc_ncs7.gpio_104 d24 */ 472 OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3) 473 474 /* cmd2 0x4a100142 uart3_rts_sd.gpio_142 f28 */ 475 OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3) 476 >; 477 }; 478 479 usb_ulpi_pins: pinmux_usb_ulpi_pins { 480 pinctrl-single,pins = < 481 OMAP4_IOPAD(0x196, MUX_MODE7) 482 OMAP4_IOPAD(0x198, MUX_MODE7) 483 OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE0) 484 OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0) 485 OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE0) 486 OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE0) 487 OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE0) 488 OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE0) 489 OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE0) 490 OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE0) 491 OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE0) 492 OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE0) 493 OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE0) 494 OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE0) 495 >; 496 }; 497 498 /* usb0_otg_dp and usb0_otg_dm */ 499 usb_utmi_pins: pinmux_usb_utmi_pins { 500 pinctrl-single,pins = < 501 OMAP4_IOPAD(0x196, PIN_INPUT | MUX_MODE0) 502 OMAP4_IOPAD(0x198, PIN_INPUT | MUX_MODE0) 503 OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7) 504 OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7) 505 OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7) 506 OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7) 507 OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE7) 508 OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE7) 509 OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7) 510 OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7) 511 OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7) 512 OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7) 513 OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7) 514 OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7) 515 >; 516 }; 517 518 /* 519 * Note that the v3.0.8 stock userspace dynamically remuxes uart1 520 * rts pin probably for PM purposes to PIN_INPUT_PULLUP | MUX_MODE7 521 * when not used. If needed, we can add rts pin remux later based 522 * on power measurements. 523 */ 524 uart1_pins: pinmux_uart1_pins { 525 pinctrl-single,pins = < 526 /* 0x4a10013c mcspi1_cs2.uart1_cts ag23 */ 527 OMAP4_IOPAD(0x13c, PIN_INPUT_PULLUP | MUX_MODE1) 528 529 /* 0x4a10013e mcspi1_cs3.uart1_rts ah23 */ 530 OMAP4_IOPAD(0x13e, MUX_MODE1) 531 532 /* 0x4a100140 uart3_cts_rctx.uart1_tx f27 */ 533 OMAP4_IOPAD(0x140, PIN_OUTPUT | MUX_MODE1) 534 535 /* 0x4a1001ca dpm_emu14.uart1_rx aa3 */ 536 OMAP4_IOPAD(0x1ca, PIN_INPUT_PULLUP | MUX_MODE2) 537 >; 538 }; 539 540 /* uart3_tx_irtx and uart3_rx_irrx */ 541 uart3_pins: pinmux_uart3_pins { 542 pinctrl-single,pins = < 543 OMAP4_IOPAD(0x196, MUX_MODE7) 544 OMAP4_IOPAD(0x198, MUX_MODE7) 545 OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7) 546 OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7) 547 OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7) 548 OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7) 549 OMAP4_IOPAD(0x1ba, MUX_MODE2) 550 OMAP4_IOPAD(0x1bc, PIN_INPUT | MUX_MODE2) 551 OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7) 552 OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7) 553 OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7) 554 OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7) 555 OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7) 556 OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7) 557 >; 558 }; 559 560 uart4_pins: pinmux_uart4_pins { 561 pinctrl-single,pins = < 562 OMAP4_IOPAD(0x15c, PIN_INPUT | MUX_MODE0) /* uart4_rx */ 563 OMAP4_IOPAD(0x15e, PIN_OUTPUT | MUX_MODE0) /* uart4_tx */ 564 OMAP4_IOPAD(0x110, PIN_INPUT_PULLUP | MUX_MODE5) /* uart4_cts */ 565 OMAP4_IOPAD(0x112, PIN_OUTPUT_PULLUP | MUX_MODE5) /* uart4_rts */ 566 >; 567 }; 568 569 mcbsp2_pins: pinmux_mcbsp2_pins { 570 pinctrl-single,pins = < 571 OMAP4_IOPAD(0x0f6, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_clkx */ 572 OMAP4_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_dr */ 573 OMAP4_IOPAD(0x0fa, PIN_OUTPUT | MUX_MODE0) /* abe_mcbsp2_dx */ 574 OMAP4_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_fsx */ 575 >; 576 }; 577 578 mcbsp3_pins: pinmux_mcbsp3_pins { 579 pinctrl-single,pins = < 580 OMAP4_IOPAD(0x106, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_dr */ 581 OMAP4_IOPAD(0x108, PIN_OUTPUT | MUX_MODE1) /* abe_mcbsp3_dx */ 582 OMAP4_IOPAD(0x10a, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_clkx */ 583 OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_fsx */ 584 >; 585 }; 586 587 vibrator_direction_pin: pinmux_vibrator_direction_pin { 588 pinctrl-single,pins = < 589 OMAP4_IOPAD(0x1ce, PIN_OUTPUT | MUX_MODE1) /* dmtimer8_pwm_evt (gpio_27) */ 590 >; 591 }; 592 593 vibrator_enable_pin: pinmux_vibrator_enable_pin { 594 pinctrl-single,pins = < 595 OMAP4_IOPAD(0X1d0, PIN_OUTPUT | MUX_MODE1) /* dmtimer9_pwm_evt (gpio_28) */ 596 >; 597 }; 598}; 599 600&omap4_pmx_wkup { 601 usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins { 602 /* gpio_wk0 */ 603 pinctrl-single,pins = < 604 OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3) 605 >; 606 }; 607}; 608 609/* RNG is used by secure mode and not accessible */ 610&rng_target { 611 status = "disabled"; 612}; 613 614/* Configure pwm clock source for timers 8 & 9 */ 615&timer8 { 616 assigned-clocks = <&abe_clkctrl OMAP4_TIMER8_CLKCTRL 24>; 617 assigned-clock-parents = <&sys_clkin_ck>; 618}; 619 620&timer9 { 621 assigned-clocks = <&l4_per_clkctrl OMAP4_TIMER9_CLKCTRL 24>; 622 assigned-clock-parents = <&sys_clkin_ck>; 623}; 624 625/* 626 * The uart1 port is wired to mdm6600 with rts and cts. The modem uses gpio_149 627 * for wake-up events for both the USB PHY and the UART. We can use gpio_149 628 * pad as the shared wakeirq for the UART rather than the RX or CTS pad as we 629 * have gpio_149 trigger before the UART transfer starts. 630 */ 631&uart1 { 632 pinctrl-names = "default"; 633 pinctrl-0 = <&uart1_pins>; 634 interrupts-extended = <&wakeupgen GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH 635 &omap4_pmx_core 0x110>; 636 uart-has-rtscts; 637 current-speed = <115200>; 638}; 639 640&uart3 { 641 interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH 642 &omap4_pmx_core 0x17c>; 643}; 644 645&uart4 { 646 pinctrl-names = "default"; 647 pinctrl-0 = <&uart4_pins>; 648 649 bluetooth { 650 compatible = "ti,wl1285-st"; 651 enable-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>; /* gpio 174 */ 652 max-speed = <3686400>; 653 }; 654}; 655 656&usbhsohci { 657 phys = <&fsusb1_phy>; 658 phy-names = "usb"; 659}; 660 661&usbhsehci { 662 phys = <&hsusb2_phy>; 663}; 664 665&usbhshost { 666 port1-mode = "ohci-phy-4pin-dpdm"; 667 port2-mode = "ehci-tll"; 668}; 669 670/* Internal UTMI+ PHY used for OTG, CPCAP ULPI PHY for detection and charger */ 671&usb_otg_hs { 672 interface-type = <1>; 673 mode = <3>; 674 675 /* 676 * Max 300 mA steps based on similar PMIC MC13783UG.pdf "Table 10-4. 677 * VBUS Regulator Main Characteristics". Binding uses 2 mA units. 678 */ 679 power = <150>; 680}; 681 682&i2c4 { 683 ak8975: magnetometer@c { 684 compatible = "asahi-kasei,ak8975"; 685 reg = <0x0c>; 686 687 vdd-supply = <&vhvio>; 688 689 interrupt-parent = <&gpio6>; 690 interrupts = <15 IRQ_TYPE_EDGE_RISING>; /* gpio175 */ 691 692 rotation-matrix = "-1", "0", "0", 693 "0", "1", "0", 694 "0", "0", "-1"; 695 696 }; 697}; 698 699&mcbsp2 { 700 #sound-dai-cells = <0>; 701 pinctrl-names = "default"; 702 pinctrl-0 = <&mcbsp2_pins>; 703 status = "okay"; 704 705 mcbsp2_port: port { 706 cpu_dai2: endpoint { 707 dai-format = "i2s"; 708 remote-endpoint = <&cpcap_audio_codec0>; 709 frame-master = <&cpcap_audio_codec0>; 710 bitclock-master = <&cpcap_audio_codec0>; 711 }; 712 }; 713}; 714 715&mcbsp3 { 716 #sound-dai-cells = <0>; 717 pinctrl-names = "default"; 718 pinctrl-0 = <&mcbsp3_pins>; 719 status = "okay"; 720 721 mcbsp3_port: port { 722 cpu_dai3: endpoint { 723 dai-format = "dsp_a"; 724 frame-master = <&cpcap_audio_codec1>; 725 bitclock-master = <&cpcap_audio_codec1>; 726 remote-endpoint = <&cpcap_audio_codec1>; 727 }; 728 }; 729}; 730 731&cpcap_audio_codec0 { 732 remote-endpoint = <&cpu_dai2>; 733}; 734 735&cpcap_audio_codec1 { 736 remote-endpoint = <&cpu_dai3>; 737}; 738