1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Common support for CompuLab CM-T3x30 CoMs
4 */
5
6#include "omap3-cm-t3x.dtsi"
7
8/ {
9	cpus {
10		cpu@0 {
11			cpu0-supply = <&vcc>;
12		};
13	};
14
15	sound {
16		compatible = "ti,omap-twl4030";
17		ti,model = "cm-t35";
18
19		ti,mcbsp = <&mcbsp2>;
20	};
21};
22
23&omap3_pmx_core {
24
25	smsc1_pins: pinmux_smsc1_pins {
26		pinctrl-single,pins = <
27			OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE0)	/* gpmc_ncs5.gpmc_ncs5 */
28			OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4)	/* uart3_cts_rctx.gpio_163 */
29		>;
30	};
31
32 	hsusb0_pins: pinmux_hsusb0_pins {
33		pinctrl-single,pins = <
34			OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_clk.hsusb0_clk */
35			OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_stp.hsusb0_stp */
36			OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_dir.hsusb0_dir */
37			OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_nxt.hsusb0_nxt */
38			OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data0.hsusb2_data0 */
39			OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data1.hsusb0_data1 */
40			OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data2.hsusb0_data2 */
41			OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data3 */
42			OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data4 */
43			OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data5 */
44			OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data6 */
45			OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data7 */
46		>;
47	};
48};
49
50#include "omap-gpmc-smsc911x.dtsi"
51
52&gpmc {
53	ranges = <5 0 0x2c000000 0x01000000>, /* CM-T3x30 SMSC9x Eth */
54		 <0 0 0x00000000 0x01000000>; /* CM-T3x NAND */
55
56	smsc1: ethernet@gpmc {
57		compatible = "smsc,lan9221", "smsc,lan9115";
58		pinctrl-names = "default";
59		pinctrl-0 = <&smsc1_pins>;
60		interrupt-parent = <&gpio6>;
61		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
62		reg = <5 0 0xff>;
63	};
64};
65
66&i2c1 {
67	twl: twl@48 {
68		reg = <0x48>;
69		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
70		interrupt-parent = <&intc>;
71
72		twl_audio: audio {
73			compatible = "ti,twl4030-audio";
74			codec {
75			};
76		};
77	};
78};
79
80#include "twl4030.dtsi"
81#include "twl4030_omap3.dtsi"
82#include <dt-bindings/input/input.h>
83
84&venc {
85	vdda-supply = <&vdac>;
86};
87
88&mmc1 {
89	vmmc-supply = <&vmmc1>;
90};
91
92&twl_gpio {
93	ti,use-leds;
94	/* pullups: BIT(0) */
95	ti,pullups = <0x000001>;
96};
97
98&twl_keypad {
99	linux,keymap = <
100				MATRIX_KEY(0x00, 0x01, KEY_A)
101				MATRIX_KEY(0x00, 0x02, KEY_B)
102				MATRIX_KEY(0x00, 0x03, KEY_LEFT)
103
104				MATRIX_KEY(0x01, 0x01, KEY_UP)
105				MATRIX_KEY(0x01, 0x02, KEY_ENTER)
106				MATRIX_KEY(0x01, 0x03, KEY_DOWN)
107
108				MATRIX_KEY(0x02, 0x01, KEY_RIGHT)
109				MATRIX_KEY(0x02, 0x02, KEY_C)
110				MATRIX_KEY(0x02, 0x03, KEY_D)
111			>;
112};
113
114&hsusb1_phy {
115	reset-gpios = <&twl_gpio 6 GPIO_ACTIVE_LOW>;
116};
117
118&hsusb2_phy {
119	reset-gpios = <&twl_gpio 7 GPIO_ACTIVE_LOW>;
120};
121
122&usb_otg_hs {
123	pinctrl-names = "default";
124	pinctrl-0 = <&hsusb0_pins>;
125	interface-type = <0>;
126	usb-phy = <&usb2_phy>;
127	phys = <&usb2_phy>;
128	phy-names = "usb2-phy";
129	mode = <3>;
130	power = <50>;
131};
132