Searched refs:INT2 (Results 1 – 21 of 21) sorted by relevance
| /linux/arch/mips/pci/ |
| A D | fixup-capcella.c | 16 #define INT2 RTL8139_2_IRQ macro
24 [12] = { -1, INT2, INT2, INT2, INT2 },
|
| /linux/Documentation/devicetree/bindings/iio/imu/ |
| A D | bosch,bmi160.yaml | 30 - INT2
33 to "INT2" if INT2 pin should be used instead
91 interrupt-names = "INT2";
|
| A D | nxp,fxos8700.yaml | 34 - INT2
78 interrupt-names = "INT2";
|
| A D | st,lsm6dsx.yaml | 42 Supports up to 2 interrupt lines via the INT1 and INT2 pins.
|
| /linux/Documentation/devicetree/bindings/iio/accel/ |
| A D | bosch,bma255.yaml | 51 the one connected to the INT2 pin (if available). The type should be
55 always treated as INT2.
63 - INT2
103 interrupt-names = "INT2";
|
| A D | fsl,mma7455.yaml | 35 to INT1 and second (where present) to INT2.
41 - "INT2"
64 interrupt-names = "INT2", "INT1";
|
| A D | fsl,mma8452.yaml | 38 - INT2
62 interrupt-names = "INT2";
|
| A D | bosch,bmi088.yaml | 43 - INT2
65 interrupt-names = "INT2";
|
| A D | nxp,fxls8962af.yaml | 38 - INT2
|
| A D | adi,adxl313.yaml | 45 - INT2
|
| A D | adi,adxl355.yaml | 37 - INT2
|
| /linux/Documentation/devicetree/bindings/iio/gyroscope/ |
| A D | nxp,fxas21002c.yaml | 44 - INT2
93 interrupt-names = "INT2";
|
| /linux/drivers/pinctrl/ |
| A D | pinctrl-pic32.c | 304 FUNCTION(INT2, input2),
440 PIC32_PINCTRL_FUNCTION(INT2, INT2R, 5),
590 PIC32_PINCTRL_FUNCTION(INT2, INT2R, 7),
617 PIC32_PINCTRL_FUNCTION(INT2, INT2R, 2),
722 PIC32_PINCTRL_FUNCTION(INT2, INT2R, 3),
800 PIC32_PINCTRL_FUNCTION(INT2, INT2R, 12),
977 PIC32_PINCTRL_FUNCTION(INT2, INT2R, 4),
1079 PIC32_PINCTRL_FUNCTION(INT2, INT2R, 0),
1210 PIC32_PINCTRL_FUNCTION(INT2, INT2R, 6),
1489 PIC32_PINCTRL_FUNCTION(INT2, INT2R, 9),
[all …]
|
| /linux/Documentation/m68k/ |
| A D | buddha-driver.rst | 103 The IDE ports issue an INT2. You can read the level of the
107 determine what driver has to serve the INT2. Buddha and
|
| /linux/Documentation/devicetree/bindings/iio/ |
| A D | st,st-sensors.yaml | 92 Intertial interrupt lines INT1 and INT2 if these exist. This means up to
|
| /linux/arch/arm/boot/dts/ |
| A D | ste-href-tvk1281618-r2.dtsi | 139 /* INT2 would need to be open drain */
|
| A D | omap3-n950-n9.dtsi | 63 OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT | MUX_MODE4) /* mcspi2_cs0.gpio_181 -> LIS302 INT2 */
|
| A D | ste-snowball.dts | 337 <4 IRQ_TYPE_EDGE_RISING>; /* INT2 */
|
| A D | imx6qdl-gw5903.dtsi | 466 interrupt-names = "INT2";
|
| A D | imx6qdl-zii-rdu2.dtsi | 389 interrupt-names = "INT2";
|
| /linux/arch/arm64/boot/dts/freescale/ |
| A D | imx8mq-zii-ultra.dtsi | 286 interrupt-names = "INT2";
|
Completed in 36 milliseconds