| /linux/arch/powerpc/kernel/ |
| A D | prom_init_check.sh | 61 OK=0
65 OK=1
73 OK=1
76 OK=1
80 if [ $OK -eq 0 ]; then
|
| /linux/drivers/net/plip/ |
| A D | plip.c | 437 return OK; in plip_bh_timeout_error()
478 return OK; in plip_none()
529 return OK; in plip_receive()
695 return OK; in plip_receive_packet()
704 return OK; in plip_receive_packet()
749 return OK; in plip_send()
751 return OK; in plip_send()
870 return OK; in plip_send_packet()
872 return OK; in plip_send_packet()
889 return OK; in plip_connection_close()
[all …]
|
| /linux/tools/testing/kunit/test_data/ |
| A D | test_is_test_passed-no_tests_run_no_header.log | 5 Checking if /dev/shm is on tmpfs...OK
6 Checking PROT_EXEC mmap in /dev/shm...OK
30 Checking host MADV_REMOVE support...OK
|
| /linux/Documentation/power/ |
| A D | video.rst | 112 Asus L2400D s3_mode (3) [#f2]_ (S1 also works OK)
114 Asus L3800C (Radeon M7) s3_bios (2) (S1 also works OK)
119 Compaq Armada E500 - P3-700 none (1) (S1 also works OK)
143 HP Omnibook 5150 none (1), (S1 also works OK)
190 Toshiba Satellite 4030CDT s3_mode (3) (S1 also works OK)
191 Toshiba Satellite 4080XCDT s3_mode (3) (S1 also works OK)
|
| /linux/tools/testing/selftests/net/ |
| A D | ipv6_flowlabel.sh | 21 echo OK. All tests passed
|
| A D | so_txtime.sh | 89 echo OK. All tests passed
|
| /linux/Documentation/translations/zh_CN/admin-guide/ |
| A D | sysrq.rst | 186 屏幕上出现 "OK" 和 "Done" 之前，同步还没有发生。
189 被重新挂载为只读。这个重新挂载动作直到你看到 "OK" 和 "Done" 信息出现在屏幕上
|
| /linux/Documentation/translations/zh_CN/doc-guide/ |
| A D | kernel-doc.rst | 132 * 0 - OK
138 Return: 0 - OK -EINVAL - invalid argument -ENOMEM - out of memory
143 * * 0 - OK to runtime suspend the device
|
| /linux/drivers/net/fddi/skfp/h/ |
| A D | sba_def.h | 63 #define OK 0x01 /* ??????? */ macro
|
| /linux/tools/testing/selftests/bpf/ |
| A D | test_tc_tunnel.sh | 291 echo OK
304 echo OK
|
| /linux/tools/build/tests/ |
| A D | run.sh | 70 echo OK
|
| /linux/Documentation/ABI/testing/ |
| A D | sysfs-bus-dfl-devices-emif | 6 memory interface. "1" for calibration failure, "0" for OK.
|
| /linux/tools/testing/selftests/lkdtm/ |
| A D | tests.txt | 74 STACKLEAK_ERASING OK: the rest of the thread stack is properly erased
|
| /linux/tools/perf/Documentation/ |
| A D | perf-daemon.txt | 173 OK cycles
174 OK sched
|
| /linux/arch/arm/boot/dts/ |
| A D | sun8i-v3-sl631.dtsi | 61 label = "OK";
|
| A D | logicpd-torpedo-37xx-devkit.dts | 29 * gpio157 is not connected. So this should be OK to keep common for now,
|
| /linux/Documentation/usb/ |
| A D | gadget_printer.rst | 118 Printer OK
141 To set error status to printer OK::
439 printf(" Printer OK\n");
|
| A D | usbip_protocol.rst | 167 | 4 | 4 | 0x00000000 | Status: 0 for OK |
259 | | | | - 0 for OK |
263 | | | | device, if the previous status field was OK (0), |
|
| A D | acm.rst | 130 If all this seems to be OK, fire up minicom and set it to talk to the ttyACM
131 device and try typing 'at'. If it responds with 'OK', then everything is
|
| /linux/tools/perf/ |
| A D | builtin-daemon.c | 68 OK, enumerator
185 session->state = OK; in session_config()
989 if (session->state == OK) in daemon__reconfig()
1010 session->state = OK; in daemon__reconfig()
|
| /linux/Documentation/scsi/ |
| A D | arcmsr_spec.rst | 20 zDRIVER DATA WRITE OK)
23 (DRIVER DATA READ OK)
28 (IOP331 DATA WRITE OK)
31 (IOP331 DATA READ OK)
|
| /linux/Documentation/userspace-api/media/cec/ |
| A D | cec-ioc-receive.rst | 241 * .. _`CEC-TX-STATUS-OK`:
262 of a transmit is just OK or FAIL. In that case this status will be
285 mutually exclusive with :ref:`CEC_TX_STATUS_OK <CEC-TX-STATUS-OK>`.
310 * .. _`CEC-RX-STATUS-OK`:
|
| /linux/drivers/net/ethernet/sis/ |
| A D | sis900.h | 200 OK = 0x08000000, DSIZE = 0x00000FFF enumerator
|
| /linux/tools/perf/tests/ |
| A D | make | 377 @echo OK
381 @echo OK
|
| /linux/tools/testing/selftests/bpf/prog_tests/ |
| A D | sockopt.c | 9 OK = 0, enumerator
958 ret = test->error != OK; in run_test()
|