| /linux/drivers/gpu/drm/nouveau/nvkm/subdev/bios/ |
| A D | boost.c | 33 u32 boost = 0; in nvbios_boostTe() local
37 boost = nvbios_rd32(bios, bit_P.offset + 0x30); in nvbios_boostTe()
39 if (boost) { in nvbios_boostTe()
40 *ver = nvbios_rd08(bios, boost + 0); in nvbios_boostTe()
43 *hdr = nvbios_rd08(bios, boost + 1); in nvbios_boostTe()
44 *cnt = nvbios_rd08(bios, boost + 5); in nvbios_boostTe()
45 *len = nvbios_rd08(bios, boost + 2); in nvbios_boostTe()
46 *snr = nvbios_rd08(bios, boost + 4); in nvbios_boostTe()
47 *ssz = nvbios_rd08(bios, boost + 3); in nvbios_boostTe()
48 return boost; in nvbios_boostTe()
|
| /linux/Documentation/devicetree/bindings/power/supply/ |
| A D | bq25890.yaml | 54 ti,boost-voltage:
56 description: VBUS voltage level in boost mode (in uV)
58 ti,boost-max-current:
60 description: maximum allowed current draw in boost mode (in uA)
62 ti,boost-low-freq:
63 description: boost mode frequency will be 500kHz, otherwise 1.5MHz
93 - ti,boost-voltage
94 - ti,boost-max-current
117 ti,boost-voltage = <5000000>;
118 ti,boost-max-current = <1000000>;
|
| A D | richtek,rt9455.yaml | 39 richtek,boost-output-voltage:
42 maximum voltage provided to consumer devices, when the charger is in boost mode, in uV.
64 - richtek,boost-output-voltage
85 richtek,boost-output-voltage = <5050000>;
|
| /linux/Documentation/devicetree/bindings/sound/ |
| A D | cs35l34.txt | 13 - cirrus,boost-vtge-millivolt : Boost Voltage Value. Configures the boost
17 - cirrus,boost-nanohenry: Inductor value for boost converter. The value is
28 - cirrus,boost-peak-milliamp : Boost converter peak current limit in mA. The
59 cirrus,boost-vtge-milltvolt = <8000>; /* 8V */
60 cirrus,boost-ind-nanohenry = <1000>; /* 1uH */
61 cirrus,boost-peak-milliamp = <3000>; /* 3A */
|
| A D | cirrus,cs35l41.yaml | 39 cirrus,boost-peak-milliamp:
42 Configures the peak current by monitoring the current through the boost FET.
50 cirrus,boost-ind-nanohenry:
58 cirrus,boost-cap-microfarad:
60 Total equivalent boost capacitance on the VBST
134 - cirrus,boost-peak-milliamp
135 - cirrus,boost-ind-nanohenry
136 - cirrus,boost-cap-microfarad
153 cirrus,boost-peak-milliamp = <4500>;
154 cirrus,boost-ind-nanohenry = <1000>;
[all …]
|
| A D | cs35l36.txt | 13 - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
18 - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
19 Configures the peak current by monitoring the current through the boost FET.
24 - cirrus,boost-ind-nanohenry : Inductor estimation LBST reference value.
36 - cirrus,boost-ctl-select : Boost conerter control source selection.
37 Selects the source of the BST_CTL target VBST voltage for the boost
53 This enables the digital boost converter to operate in a low power
147 cirrus,boost-ind-nanohenry = <1000>;
148 cirrus,boost-ctl-millivolt = <10000>;
149 cirrus,boost-peak-milliamp = <4500>;
[all …]
|
| A D | cs35l35.txt | 17 - cirrus,boost-ind-nanohenry: Inductor value for boost converter. The value is
34 - cirrus,shared-boost : Boolean to enable ClassH tracking of Advisory Signal
37 - cirrus,external-boost : Boolean to specify the device is using an external
38 boost supply, note that sharing a boost from another cs35l35 would constitute
55 - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
60 - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
61 Configures the peak current by monitoring the current through the boost FET.
150 cirrus,boost-ctl-millivolt = <9000>;
155 cirrus,shared-boost;
|
| A D | cs35l33.txt | 21 - cirrus,boost-ctl : Booster voltage use to supply the amp. If the value is
22 0, then VBST = VP. If greater than 0, the boost voltage will be 3300mV with
34 - cirrus,boost-ipk : The maximum current allowed for the boost converter.
109 cirrus,boost-ctl = <0x30>; /* VBST = 8000mV */
110 cirrus,boost-ipk = <0xE0>; /* 3600mA */
|
| A D | cs35l32.txt | 18 - cirrus,boost-manager : Boost voltage control.
59 cirrus,boost-manager = <0x03>;
|
| /linux/Documentation/devicetree/bindings/mfd/ |
| A D | max77693.txt | 89 - maxim,boost-mode :
90 In boost mode the device can produce up to 1.2A of total current
92 to 625mA then. If not enabled explicitly, boost setting defaults to
95 LEDS_BOOST_OFF (0) - no boost,
98 - maxim,boost-mvout : Output voltage of the boost module in millivolts.
117 (boost mode must be turned off):
182 maxim,boost-mode = <LEDS_BOOST_FIXED>;
183 maxim,boost-mvout = <5000>;
|
| A D | st,stpmic1.yaml | 99 - boost for Buck BOOST
167 boost:
187 "^(buck[1-4]|ldo[1-6]|boost|pwr_sw[1-2])-supply$":
190 "^(buck[1-4]|ldo[1-6]|boost|vref_ddr|pwr_sw[1-2])$":
|
| /linux/Documentation/usb/ |
| A D | iuu_phoenix.rst | 40 boost:
41 overclock boost percent 100 to 500 (int)
57 - boost provide a way to overclock the reader ( my favorite :-) )
60 modprobe boost=195
84 use this settings to deduce de boost but is that feature
|
| /linux/drivers/usb/serial/ |
| A D | iuu_phoenix.c | 38 static int boost = 100; variable
61 u32 boost; member
918 baud * priv->boost / 100, in iuu_set_termios()
989 if (boost < 100) in iuu_open()
990 boost = 100; in iuu_open()
991 priv->boost = boost; in iuu_open()
995 iuu_clk(port, IUU_CLK_3680000 * boost / 100); in iuu_open()
997 iuu_uart_baud(port, baud * boost / 100, &actual, in iuu_open()
1001 iuu_clk(port, IUU_CLK_6000000 * boost / 100); in iuu_open()
1009 iuu_clk(port, IUU_CLK_3579000 * boost / 100); in iuu_open()
[all …]
|
| /linux/Documentation/devicetree/bindings/leds/backlight/ |
| A D | qcom-wled.yaml | 74 qcom,current-boost-limit:
76 mA; boost current limit.
173 qcom,current-boost-limit:
191 qcom,current-boost-limit:
249 qcom,current-boost-limit = <805>;
|
| /linux/Documentation/devicetree/bindings/regulator/ |
| A D | richtek,rtq6752-regulator.yaml | 14 two synchronous boost converter for PAVDD, and one synchronous NAVDD
15 buck-boost. The device is suitable for automotive TFT-LCD panel.
|
| A D | qcom-labibb-regulator.yaml | 13 LAB can be used as a positive boost power supply and IBB can be used as a
14 negative boost power supply for display panels. Currently implemented for
|
| /linux/Documentation/devicetree/bindings/ata/ |
| A D | imx-sata.yaml | 45 fsl,transmit-boost-mdB:
47 description: transmit boost level, in milli-decibels.
|
| /linux/Documentation/devicetree/bindings/display/panel/ |
| A D | novatek,nt36672a.yaml | 42 description: phandle of the positive boost supply regulator
45 description: phandle of the negative boost supply regulator
|
| /linux/Documentation/translations/zh_CN/cpu-freq/ |
| A D | cpu-drivers.rst | 88 .boost_enabled - 如果设置，则启用提升(boost)频率。
90 .set_boost - 一个指向per-policy函数的指针，该函数用来开启/关闭提升(boost)频率功能。
|
| /linux/Documentation/translations/zh_TW/cpu-freq/ |
| A D | cpu-drivers.rst | 89 .boost_enabled - 如果設置，則啓用提升(boost)頻率。
91 .set_boost - 一個指向per-policy函數的指針，該函數用來開啓/關閉提升(boost)頻率功能。
|
| /linux/drivers/power/supply/ |
| A D | bq2415x_charger.c | 726 int boost = 0; in bq2415x_set_mode() local
729 boost = 1; in bq2415x_set_mode()
736 if (!boost) in bq2415x_set_mode()
770 else if (boost) in bq2415x_set_mode()
891 int boost; in bq2415x_timer_work() local
907 boost = bq2415x_exec_command(bq, BQ2415X_BOOST_MODE_STATUS); in bq2415x_timer_work()
908 if (boost < 0) { in bq2415x_timer_work()
919 if (boost) { in bq2415x_timer_work()
|
| /linux/kernel/sched/ |
| A D | cpufreq_schedutil.c | 264 unsigned long boost; in sugov_iowait_apply() local
291 boost = (sg_cpu->iowait_boost * sg_cpu->max) >> SCHED_CAPACITY_SHIFT; in sugov_iowait_apply()
292 if (sg_cpu->util < boost) in sugov_iowait_apply()
293 sg_cpu->util = boost; in sugov_iowait_apply()
|
| /linux/Documentation/admin-guide/pm/ |
| A D | cpufreq.rst | 609 term "frequency boost" is used here for brevity to refer to all of those
612 The frequency boost mechanism may be either hardware-based or software-based.
619 The ``boost`` File in ``sysfs``
623 the "boost" setting for the whole system. It is not present if the underlying
624 scaling driver does not support the frequency boost mechanism (or supports it,
636 If the value in this file is 0, the frequency boost mechanism is disabled and
649 For this reason, many systems make it possible to disable the frequency boost
658 limited capacity, such as batteries, so the ability to disable the boost
674 frequency boost mechanism before running benchmarks sensitive to that
681 the global ``boost`` one. It is used for disabling/enabling the "Core
[all …]
|
| /linux/sound/pcmcia/vx/ |
| A D | vxpocket.h | 37 void vx_set_mic_boost(struct vx_core *chip, int boost);
|
| /linux/Documentation/devicetree/bindings/phy/ |
| A D | apm-xgene-phy.txt | 27 - apm,tx-boost-gain : Frequency boost AC (LSB 3-bit) and DC (2-bit)
|