| /linux/Documentation/devicetree/bindings/mfd/ |
| A D | samsung,s2mps11.yaml | 45 samsung,s2mps11-acokb-ground:
53 samsung,s2mps11-wrstbi-ground:
79 samsung,s2mps11-wrstbi-ground: false
90 samsung,s2mps11-acokb-ground: false
101 samsung,s2mps11-acokb-ground: false
102 samsung,s2mps11-wrstbi-ground: false
113 samsung,s2mps11-acokb-ground: false
114 samsung,s2mps11-wrstbi-ground: false
125 samsung,s2mps11-acokb-ground: false
126 samsung,s2mps11-wrstbi-ground: false
[all …]
|
| /linux/Documentation/devicetree/bindings/hwmon/ |
| A D | ntc-thermistor.yaml | 20 When used in practice, a thermistor is often connected between ground, a
35 / | | "connected ground"
49 called "connected ground" and "connected positive" and shall be understood as
57 connected to ground and we get the thermistor under the pull-up resistor
62 ground" and "connected positive" cases.
114 to be connected-ground, which usually means a pull-down resistance of
|
| /linux/Documentation/hwmon/ |
| A D | ntc_thermistor.rst | 56 -+- (ground)
68 -+- (ground)
80 -+----+- (ground)
92 -+- (ground)
|
| A D | smsc47m192.rst | 108 to ground or Vcc. '1' indicates a diode fault.
|
| A D | adm1026.rst | 96 voltage from the power lead rather than on the ground lead.
|
| /linux/Documentation/devicetree/bindings/iio/adc/ |
| A D | fsl,imx25-gcq.yaml | 96 0: XN ground reference
97 1: YN ground reference
98 2: Internal ground reference
99 3: External ground reference (default)
|
| A D | ti,adc12138.yaml | 43 If not specified, this is assumed to be analog ground.
|
| /linux/drivers/extcon/ |
| A D | extcon-intel-mrfld.c | 98 bool ground; in mrfld_extcon_get_id() local
122 ground = id & BCOVE_USBIDSTS_GND; in mrfld_extcon_get_id()
125 return ground ? INTEL_USB_ID_GND : INTEL_USB_ID_FLOAT; in mrfld_extcon_get_id()
127 return ground ? INTEL_USB_ID_FLOAT : INTEL_USB_ID_GND; in mrfld_extcon_get_id()
|
| /linux/Documentation/devicetree/bindings/iio/proximity/ |
| A D | semtech,sx9310.yaml | 43 semtech,cs0-ground:
44 description: Indicates the CS0 sensor is connected to ground.
121 semtech,cs0-ground;
|
| /linux/Documentation/devicetree/bindings/sound/ |
| A D | qcom,wcd938x.yaml | 67 qcom,ground-jack-type-normally-closed:
117 qcom,ground-jack-type-normally-closed;
|
| A D | qcom,wcd934x.yaml | 84 qcom,ground-jack-type-normally-closed:
188 qcom,ground-jack-type-normally-closed;
|
| /linux/Documentation/devicetree/bindings/leds/ |
| A D | richtek,rt8515.yaml | 60 ground. The maximum hardware current setting is calculated
72 ground. The maximum hardware current setting is calculated
|
| A D | leds-pwm.yaml | 39 For PWMs where the LED is wired to supply rather than ground.
|
| /linux/Documentation/devicetree/bindings/iio/dac/ |
| A D | maxim,ds4424.yaml | 41 reg = <0x10>; /* When A0, A1 pins are ground */
|
| /linux/drivers/iio/position/ |
| A D | Kconfig | 28 and keyboard angle respect to horizon (ground).
|
| /linux/Documentation/devicetree/bindings/iio/ |
| A D | mount-matrix.txt | 96 ground plane and positive towards magnetic North, (x) is in the ground plane,
98 perpendicular to the ground plane and positive upwards.
|
| /linux/drivers/auxdisplay/ |
| A D | Kconfig | 378 0 : no connection (eg: connected to ground)
393 0 : no connection (eg: connected to ground)
408 0 : no connection (eg: connected to ground)
423 0 : no connection (eg: connected to ground)
438 0 : no connection (eg: connected to ground)
453 0 : no connection (eg: connected to ground)
|
| /linux/arch/arm/boot/dts/ |
| A D | rk3288-veyron-sdmmc.dtsi | 34 * Builtin CD line is hooked to ground to prevent JTAG at boot
|
| A D | kirkwood-openblocks_a7.dts | 84 * ground.
|
| /linux/Documentation/w1/ |
| A D | w1-generic.rst | 6 signal wire (plus ground, so two wires).
8 Devices communicate on the bus by pulling the signal to ground via an open
|
| /linux/arch/arm64/boot/dts/qcom/ |
| A D | sc7180-trogdor-lazor.dtsi | 17 semtech,cs0-ground;
|
| /linux/Documentation/devicetree/bindings/gpio/ |
| A D | nxp,pcf8575.yaml | 14 driven high by a pull-up current source or driven low to ground. This
|
| /linux/Documentation/ABI/testing/ |
| A D | sysfs-bus-iio | 625 1kohm_to_gnd: connected to ground via an 1kOhm resistor,
626 2.5kohm_to_gnd: connected to ground via a 2.5kOhm resistor,
627 6kohm_to_gnd: connected to ground via a 6kOhm resistor,
628 20kohm_to_gnd: connected to ground via a 20kOhm resistor,
629 90kohm_to_gnd: connected to ground via a 90kOhm resistor,
630 100kohm_to_gnd: connected to ground via an 100kOhm resistor,
631 125kohm_to_gnd: connected to ground via an 125kOhm resistor,
632 500kohm_to_gnd: connected to ground via a 500kOhm resistor,
633 640kohm_to_gnd: connected to ground via a 640kOhm resistor,
1803 * X is in the ground plane, perpendicular to the North axis and
[all …]
|
| /linux/Documentation/misc-devices/ |
| A D | lis3lv02d.rst | 95 fall to the ground is out of question...
|
| /linux/Documentation/sound/designs/ |
| A D | channel-mapping-api.rst | 41 As a ground design, each PCM substream may contain a control element
|