| /linux/drivers/base/test/ |
| A D | Kconfig | 3 tristate "Build kernel module to test asynchronous driver probing"
7 testing asynchronous driver probing by the device core.
|
| /linux/Documentation/driver-api/ |
| A D | eisa.rst | 25 implements bus probing (detecting EISA cards available on the bus),
53 to this device, as well as some parameters for probing purposes::
197 Force the probing code to probe EISA slots even when it cannot find an
199 (don't force), and set to 1 (force probing) when either
206 code (since probing is now in the core EISA code). Unfortunately, most
207 drivers share their probing routine between ISA, and EISA. Special
215 Unfortunately, most drivers are doing the probing by themselves, and
|
| A D | device_link.rst | 64 presence of the supplier after adding the link, and defer probing on
66 ``->probe`` callback while the supplier is still probing, but the consumer must
111 may cause probing of the consumer to be deferred indefinitely. This can become
144 probing) or never. Consequently it cannot be determined whether to defer
145 probing or not. It would be possible to notify drivers when optional
146 resources become available after probing, but it would come at a high cost
249 A more suitable approach might be to simply use deferred probing or
309 probing are waited for until they are done.
|
| A D | firewire.rst | 28 Firewire device probing and sysfs interfaces
|
| /linux/net/tipc/ |
| A D | monitor.c | 493 bool probing = state->probing; in tipc_mon_rcv() local
496 state->probing = false; in tipc_mon_rcv()
517 if (!more(new_gen, state->peer_gen) && !probing) in tipc_mon_rcv()
605 state->probing = false; in tipc_mon_get_state()
611 if (!state->probing && in tipc_mon_get_state()
619 state->probing = state->acked_gen != mon->dom_gen; in tipc_mon_get_state()
620 state->probing |= peer->down_cnt; in tipc_mon_get_state()
|
| A D | monitor.h | 55 bool probing :1; member
|
| /linux/Documentation/ide/ |
| A D | ide.rst | 82 Drives are normally found by auto-probing and/or examining the CMOS/BIOS data.
96 The results of successful auto-probing may override the physical geometry/irq
100 If the auto-probing during boot time confuses a drive (ie. the drive works
191 you need to explicitly enable probing by using "probe" kernel parameter,
192 i.e. to enable probing for ALI M14xx chipsets (ali14xx host driver) use:
200 kernel paremeter to enable probing for VLB version of the chipset (PCI ones
227 * "noprobe=[interface_number.device_number]" to skip probing
|
| /linux/tools/bpf/bpftool/Documentation/ |
| A D | bpftool-feature.rst | 50 specified, probing the kernel is the default behaviour.
67 same role as when probing the kernel.
|
| /linux/sound/ac97/ |
| A D | Kconfig | 11 drivers which benefit from the AC97 automatic probing should "select"
|
| /linux/Documentation/fb/ |
| A D | intel810.rst | 54 - Supports EDID probing either by DDC/I2C or through the BIOS
102 be equal to hsync2. If EDID probing is successful, these will be
111 rate. If EDID probing is successful, these will be ignored and values
250 e. If you want support for DDC/I2C probing (Plug and Play Displays),
|
| /linux/Documentation/devicetree/bindings/display/connector/ |
| A D | vga-connector.yaml | 19 description: phandle link to the I2C controller used for DDC EDID probing
|
| A D | hdmi-connector.yaml | 32 description: phandle link to the I2C controller used for DDC EDID probing
|
| A D | dvi-connector.yaml | 23 description: phandle link to the I2C controller used for DDC EDID probing
|
| /linux/Documentation/devicetree/bindings/mfd/ |
| A D | max77686.txt | 7 client while probing.This document describes the binding for mfd device and
|
| /linux/Documentation/hwmon/ |
| A D | ltc4215.rst | 30 of the possible addresses are unfriendly to probing. You will have to
|
| /linux/Documentation/PCI/ |
| A D | pci-iov-howto.rst | 90 To enable auto probing VFs by a compatible driver on the host, run
98 To disable auto probing VFs by a compatible driver on the host, run
|
| /linux/Documentation/ABI/testing/ |
| A D | sysfs-class-devlink | 76 - 'consumer probing'
91 'consumer probing' means the consumer device is currently
|
| /linux/Documentation/devicetree/bindings/display/ |
| A D | brcm,bcm2835-hdmi.yaml | 37 Phandle of the I2C controller used for DDC EDID probing
|
| /linux/drivers/mtd/chips/ |
| A D | Kconfig | 12 for probing the capabilities of flash devices. If you wish to
22 This option enables JEDEC-style probing of flash chips which are not
227 This option enables support for a dummy probing driver used to
|
| /linux/drivers/phy/mediatek/ |
| A D | Kconfig | 26 Enable this to provide vendor-specific probing,
|
| /linux/Documentation/driver-api/driver-model/ |
| A D | overview.rst | 26 of common callbacks, such as device discovery during bus probing, bus
115 The bus layer may also create files for the devices it finds while probing the
|
| /linux/sound/pci/hda/ |
| A D | hda_controller.h | 138 unsigned int probing:1; /* codec probing phase */ member
|
| /linux/Documentation/gpu/ |
| A D | vc4.rst | 13 display, output probing and related topics.
|
| /linux/Documentation/usb/ |
| A D | acm.rst | 121 acm.c: probing config 1
122 acm.c: probing config 2
|
| /linux/Documentation/devicetree/bindings/virtio/ |
| A D | iommu.txt | 4 discovered dynamically by the PCI probing infrastructure. However the
|