| /linux/drivers/rtc/ |
| A D | rtc-ds1343.c | 147 char *diodes = "disabled", *resistors = " "; in ds1343_show_tricklecharger() local
166 resistors = "1k Ohm"; in ds1343_show_tricklecharger()
170 resistors = "2k Ohm"; in ds1343_show_tricklecharger()
174 resistors = "4k Ohm"; in ds1343_show_tricklecharger()
183 return sprintf(buf, "%s %s\n", diodes, resistors); in ds1343_show_tricklecharger()
|
| A D | rtc-ds1305.c | 386 char *resistors = ""; in ds1305_proc() local
402 resistors = "2k Ohm"; in ds1305_proc()
405 resistors = "4k Ohm"; in ds1305_proc()
408 resistors = "8k Ohm"; in ds1305_proc()
417 seq_printf(seq, "trickle_charge\t: %s%s\n", diodes, resistors); in ds1305_proc()
|
| /linux/Documentation/devicetree/bindings/leds/ |
| A D | richtek,rt8515.yaml | 15 current for each mode is defined in hardware using two resistors
34 resistors limits the maximum flash current. This must be set
43 resistors limits the maximum torch current. This must be set
|
| A D | leds-lm3532.txt | 11 each with 32 internal voltage setting resistors, 8-bit logarithmic and linear
|
| /linux/drivers/gpu/drm/nouveau/nvkm/subdev/bios/ |
| A D | iccsense.c | 122 rail->resistors[r].mohm = nvbios_rd08(bios, entry + res_start + r * 2); in nvbios_iccsense_parse()
123 rail->resistors[r].enabled = !(nvbios_rd08(bios, entry + res_start + r * 2 + 1) & 0x40); in nvbios_iccsense_parse()
|
| /linux/Documentation/hwmon/ |
| A D | ina3221.rst | 48 value for their shunt resistors)
53 value for their shunt resistors)
|
| A D | w83l785ts.rst | 25 of external resistors, so the user cannot change it. Values seen so
|
| A D | ltc4260.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
|
| A D | ltc4261.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
|
| A D | ltc2945.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
|
| A D | vt1211.rst | 84 external scaling resistors. This external scaling needs to be compensated for
89 The board level scaling resistors according to VIA's recommendation are as
|
| A D | ltc4245.rst | 49 rely on the sense resistors listed in Table 2: "Sense Resistor Values".
|
| /linux/drivers/gpu/drm/nouveau/include/nvkm/subdev/bios/ |
| A D | iccsense.h | 13 struct pwr_rail_resistor_t resistors[3]; member
|
| /linux/Documentation/devicetree/bindings/pinctrl/ |
| A D | mediatek,mt6797-pinctrl.yaml | 106 Pull up setings for 2 pull resistors, R0 and R1. User can
117 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| A D | mediatek,mt6779-pinctrl.yaml | 113 Pull up setings for 2 pull resistors, R0 and R1. User can
124 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| A D | mediatek,mt8183-pinctrl.yaml | 138 Pull up setings for 2 pull resistors, R0 and R1. User can
149 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| A D | mediatek,mt7986-pinctrl.yaml | 294 Pull up setings for 2 pull resistors, R0 and R1. Valid arguments
306 Pull down setings for 2 pull resistors, R0 and R1. Valid arguments
|
| A D | mediatek,mt65xx-pinctrl.yaml | 95 settings for 2 pull resistors, R0 and R1. User can configure those
|
| /linux/Documentation/devicetree/bindings/hwmon/ |
| A D | ntc-thermistor.yaml | 13 Thermistors with negative temperature coefficient (NTC) are resistors that
60 We can use both pull-up and pull-down resistors at the same time, and then
|
| /linux/Documentation/devicetree/bindings/gpio/ |
| A D | gpio-xra1403.txt | 5 - Internal pull-up resistors
|
| /linux/Documentation/devicetree/bindings/iio/imu/ |
| A D | st,lsm6dsx.yaml | 62 description: enable/disable internal i2c controller pullup resistors.
|
| /linux/Documentation/ABI/stable/ |
| A D | sysfs-class-udc | 63 Allows users to disconnect data pullup resistors thus causing a
|
| /linux/arch/arm/mach-s3c/ |
| A D | Kconfig.s3c64xx | 206 resistors fitted so that the card detects for
215 resistors fitted so that the card detects for
|
| /linux/Documentation/devicetree/bindings/mfd/ |
| A D | gateworks-gsc.yaml | 91 description: Values of resistors for divider on raw ADC input
|
| /linux/Documentation/devicetree/bindings/sound/ |
| A D | cs42l42.txt | 66 clean connection with the bias resistors.
|