Searched refs:CSI (Results 1 – 16 of 16) sorted by relevance
| /u-boot/arch/arm/mach-rockchip/rk3399/ |
| A D | Kconfig | 46 * HDMI, eDP, MIPI-DSI, MIPI-DSI/CSI and MIPI-CSI
87 * HDMI In/Out, DP, MIPI DSI/CSI, eDP
105 * HDMI In/Out, DP, MIPI DSI/CSI, eDP
|
| /u-boot/arch/arm/mach-sunxi/ |
| A D | dram_sunxi_dw.c | 130 MBUS_CONF( CSI, true, HIGHEST, 0, 256, 128, 32); in mctl_set_master_priority_h3()
155 MBUS_CONF( CSI, true, HIGHEST, 0, 384, 256, 0); in mctl_set_master_priority_v3s()
178 MBUS_CONF( CSI, true, HIGH, 0, 256, 128, 0); in mctl_set_master_priority_a64()
208 MBUS_CONF( CSI, true, HIGHEST, 0, 150, 120, 100); in mctl_set_master_priority_h5()
236 MBUS_CONF( CSI, true, HIGHEST, 0, 150, 120, 100); in mctl_set_master_priority_r40()
|
| /u-boot/board/theobroma-systems/puma_rk3399/ |
| A D | README | 20 * Camera: 2x CSI (one on the edge connector, one on the Q7 specified CSI ZIF)
|
| /u-boot/drivers/clk/ |
| A D | clk_stm32h7.c | 448 CSI, enumerator
458 [CSI] = "clk-csi",
514 pllsrc = stm32_get_rate(regs, CSI); in stm32_get_PLL1_rate()
658 sysclk = stm32_get_rate(regs, CSI); in stm32_clk_get_rate()
|
| /u-boot/arch/arm/mach-rockchip/rk3368/ |
| A D | Kconfig | 39 with integrated CVBS (TP2825) / MIPI DSI / CSI / LVDS
|
| /u-boot/arch/arm/dts/ |
| A D | sun50i-a64-amarula-relic.dts | 43 reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>; /* CSI-RST-R: PE14 */
44 powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* CSI-STBY-R: PE15 */
|
| A D | ste-ab8505.dtsi | 248 // supply for U8500 CSI/DSI; VANA LDO
|
| A D | sun4i-a10-gemei-g9.dts | 67 * 2x cameras via CSI
|
| A D | ste-ab8500.dtsi | 301 // supply for U8500 CSI/DSI; VANA LDO
|
| A D | sun8i-r16-bananapi-m2m.dts | 141 /* This is the i2c bus exposed on the CSI connector to control the sensor */
|
| /u-boot/arch/arm/mach-tegra/tegra114/ |
| A D | clock.c | 294 NONE(CSI),
|
| /u-boot/arch/arm/mach-tegra/tegra124/ |
| A D | pinmux.c | 320 MIPIPADCTRL_GRP(DSI_B, CSI, DSI_B),
|
| A D | clock.c | 394 NONE(CSI),
|
| /u-boot/arch/arm/mach-tegra/tegra30/ |
| A D | clock.c | 294 NONE(CSI),
|
| /u-boot/drivers/power/ |
| A D | Kconfig | 178 On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and
|
| /u-boot/arch/arm/mach-tegra/tegra210/ |
| A D | clock.c | 427 NONE(CSI),
|
Completed in 22 milliseconds