Home
last modified time | relevance | path

Searched refs:DIP (Results 1 – 25 of 27) sorted by relevance

12

/u-boot/board/cadence/xtfpga/
A DREADME51 The LX60/LX110/LX200/ML605 contain an 8-way DIP switch that controls
55 Boot Mapping (DIP switch 8):
57 DIP switch 8 maps the system ROM address space (in which the
60 and cannot be disabled by software, therefore DIP switch 8 is no
61 available for application use. Note DIP switch 7 is reserved by
80 Default MAC Address (DIP switches 1-6):
84 value whose least significant 6 bits come from DIP switches 1-6.
86 according to the DIP switches, where "on"==1 and "off"==0, and
93 used and the DIP switches no longer consulted. DIP swithes 1-6
96 The KC705 board contains 4-way DIP switch, way 1 is the boot mapping
/u-boot/board/phytec/pcm058/
A DREADME25 The dip switch "DIP-1" on the board let choose between
28 DIP-1 set to off: Boot first from NAND, then try SPI
29 DIP-1 set to on: Boot first from SD, then try SPI
31 The bootloader was tested with DIP-1 set to on. If a SD-card
/u-boot/board/freescale/mx28evk/
A DREADME17 To boot MX28EVK from an SD card, set the boot mode DIP switches as:
26 To boot MX28EVK from SPI NOR flash, set the boot mode DIP switches as:
/u-boot/board/freescale/p2041rdb/
A DREADME36 5. Change DIP-switch
59 5. Change DIP-switch
84 5. Change DIP-switch
/u-boot/board/freescale/mpc8315erdb/
A DREADME8 To boot the image at 0xFE000000 in NOR flash, use these DIP
19 DIP switch settings for S3 S4:
/u-boot/board/beacon/imx8mn/
A DREADME37 Set baseboard DIP switch:
/u-boot/board/freescale/mpc8313erdb/
A DREADME8 To boot the image at 0xFE000000 in NOR flash, use these DIP
19 DIP switch settings for S3 S4:
/u-boot/board/freescale/p1_p2_rdb_pc/
A DREADME35 SD width is based off DIP switch. DIP switch is detected on the
/u-boot/board/kobol/helios4/
A DREADME37 Set the SW1 DIP switches to UART boot (see above).
/u-boot/board/freescale/p1010rdb/
A DREADME.P1010RDB-PB62 P1010RDB-PB default DIP-switch settings
71 P1010RDB-PB boot mode settings via DIP-switch
80 Switch P1010RDB-PB boot mode via software without setting DIP-switch
A DREADME.P1010RDB-PA80 Settings of DIP-switch
/u-boot/board/freescale/mpc832xemds/
A DREADME4 1.0 There are five Dual-In-Line Packages(DIP) Switches on MPC832XE SYS board
102 1)Make sure the DIP SW support PCI mode as described in Section 1.1.
/u-boot/board/solidrun/clearfog/
A DREADME65 Set the SW1 DIP switches to UART boot (see above).
/u-boot/board/freescale/t102xrdb/
A DREADME202 via DIP-switch: set SW3[5:7] = '100'
205 via DIP-switch: set SW3[5:7] = '100'
210 via DIP-Switch: set SW3[5:7] = '000'
213 via DIP-switch: set SW3[5:7] = '000'
/u-boot/board/freescale/t208xrdb/
A DREADME144 T2080PCIe-RDB Default DIP-Switch setting
164 via DIP-switch: set SW3[5:7] = '100'
168 via DIP-Switch: set SW3[5:7] = '000'
/u-boot/include/
A Dsym53c8xx.h101 #define DIP 0x01 /* sta: host/script interrupt */ macro
/u-boot/board/freescale/mpc837xemds/
A DREADME4 1.0 There are four Dual-In-Line Packages(DIP) Switches on MPC837xEMDS board
/u-boot/doc/board/tbs/
A Dtbs2910.rst43 SW6 binary DIP switch array on the PCB revision 2.1:
78 SW6 binary DIP switch array on the PCB revision 2.3:
/u-boot/doc/imx/common/
A Dmxs.txt142 To boot a MXS based board from SD, set the boot mode DIP switches according to
191 To boot a MX28 based board from NAND, set the boot mode DIP switches according
287 Power off the board and set the boot mode DIP switches to boot from the SPI NOR
/u-boot/board/synopsys/emsdp/
A DREADME74 power-on. For that make sure VCCIO DIP-switches are all in "off" state.
/u-boot/board/freescale/t208xqds/
A DREADME176 by DIP-switch: set SW6[1:4] = '0100'
180 by DIP-Switch: set SW6[1:4] = '0000'
/u-boot/board/synopsys/hsdk/
A DREADME96 SPI-flash on power-on. For that make sure DIP-switches in the corner of
/u-boot/arch/arm/dts/
A Dam3517-evm.dts214 /* User DIP swithes [1:8] / User LEDS [1:2] */
A Ddra72-evm-common.dtsi304 /* To use NAND, DIP switch SW5 must be set like so:
/u-boot/doc/board/freescale/
A Db4860qds.rst91 reset source. The RCW source is set by appropriate DIP-switches.

Completed in 14 milliseconds

12