| /u-boot/drivers/ata/ |
| A D | Kconfig | 2 bool "Support SATA controllers with driver model"
10 config SATA config
11 bool "Support SATA controllers"
14 This enables support for SATA (Serial Advanced Technology
30 bool "Enable SCSI interface to SATA devices"
35 menu "SATA/SCSI device support"
92 bool "Enable Marvell SATA controller driver support"
106 SATA controllers.
115 bool "Enable Allwinner SATA driver support"
123 bool "Marvell EBU AHCI SATA support"
[all …]
|
| /u-boot/board/phytium/durian/ |
| A D | README | 44 SATA link 1 timeout.
45 SATA link 2 timeout.
46 SATA link 3 timeout.
47 AHCI 0001.0000 32 slots 4 ports 6 Gbps 0xf impl SATA mode
52 SATA link 0 timeout.
53 SATA link 1 timeout.
54 SATA link 2 timeout.
55 SATA link 3 timeout.
56 AHCI 0001.0000 32 slots 4 ports 6 Gbps 0xf impl SATA mode
|
| /u-boot/doc/ |
| A D | README.sata | 1 1. SATA usage in U-Boot
5 * Read/write raw blocks from/to SATA hard disk
8 1.0 How to read the SATA hard disk's information?
12 SATA device 0: Model: ST3320620AS Firm: 3.AAD Ser#: 4QF01ZTN
17 1.1 How to raw write the kernel, file system, dtb to a SATA hard disk?
34 1.2 How to raw read the kernel, file system, dtb from a SATA hard disk?
|
| /u-boot/board/freescale/ls1021aiot/ |
| A D | ls102xa_rcw_sd.cfg | 5 #Default with 2 x SGMII (no SATA)
11 #SATA set-up
|
| A D | README | 32 - SATA
33 - Support SATA Connector
|
| /u-boot/doc/device-tree-bindings/ata/ |
| A D | intel-sata.txt | 1 Intel Pantherpoint SATA Device Binding
5 SATA device is as follows:
13 - intel,sata-port-map : Which SATA ports are enabled, bit 0=enable first port,
|
| /u-boot/doc/device-tree-bindings/phy/ |
| A D | no-op.txt | 3 This driver is used to stub PHY operations in a driver (USB, SATA).
4 This is useful when the 'client' driver (USB, SATA, ...) uses the PHY framework
|
| /u-boot/board/solidrun/clearfog/ |
| A D | Kconfig | 19 bool "Use CON3 slot in SATA mode"
21 Use the CON3 port with SATA protocol instead of the default PCIe.
27 bool "Use CON2 slot in SATA mode"
30 Use the CON2 port with SATA protocol instead of the default PCIe.
|
| /u-boot/arch/arm/dts/ |
| A D | armada-388.dtsi | 10 * SATA ports. So we can reuse the dtsi of the Armada 385, override the pinctrl
11 * property and the name of the SoC, and add the second SATA host which control
|
| A D | r8a774a1-hihope-rzg2m-ex.dts | 18 /* SW43 should be OFF, if in ON state SATA port will be activated */
|
| /u-boot/board/freescale/ls1012ardb/ |
| A D | README | 19 - SATA 3.0
34 - One SATA onboard connectors
60 - SATA 3.0
70 - One SATA onboard connectors
|
| /u-boot/board/intel/ |
| A D | Kconfig | 16 4GB memory, HDMI/DP/VGA display, HD audio, SATA, USB2, USB3, SD, eMMC,
25 serial console, 10/100/1000 Ethernet, SD-Card, USB 2/3, SATA, PCIe,
34 peripheral connectors for PCIe/SATA/USB2/USB3/LAN/UART/PS2/VGA/HDMI.
43 peripheral connectors for PCIe/SATA/USB/LAN/SD/UART/Audio/LVDS.
70 USB 3, SATA, serial console, some GPIOs and HDMI 1.3 video out.
|
| /u-boot/board/freescale/ls1046aqds/ |
| A D | ls1046aqds_pbi.cfg | 13 #Serdes SATA
|
| /u-boot/board/freescale/ls1046ardb/ |
| A D | ls1046ardb_pbi.cfg | 11 #Serdes SATA
|
| A D | ls1046ardb_qspi_pbi.cfg | 13 #Serdes SATA
|
| /u-boot/board/congatec/ |
| A D | Kconfig | 19 USB 3, SATA, serial console and HDMI 1.3 video out.
30 micro-SD, USB 2, USB 3, SATA, serial console and HDMI 1.3 video
|
| /u-boot/board/dfi/ |
| A D | Kconfig | 17 USB 3, SATA, serial console and DisplayPort video out.
30 USB 3, SATA, serial console and DisplayPort video out.
|
| /u-boot/board/freescale/ls1088a/ |
| A D | README | 44 - SATA 3.0
62 - Two SATA onboard connectors
108 - SATA 3.0
128 - Two SATA onboard connectors
|
| /u-boot/include/configs/ |
| A D | udoo.h | 68 func(SATA, sata, 0) \
|
| A D | tbs2910.h | 104 func(SATA, sata, 0) \
|
| A D | mx6cuboxi.h | 96 func(SATA, sata, 0) \
|
| /u-boot/arch/arm/mach-tegra/tegra210/ |
| A D | Kconfig | 20 HDMI, USB micro-B port, Ethernet via USB3, USB3 host port, SATA,
30 port, SATA, PCIe, and two GPIO expansion headers.
|
| /u-boot/board/freescale/ls1012aqds/ |
| A D | README | 19 - SATA 3.0
35 - One SATA onboard connectors
|
| /u-boot/board/kobol/helios4/ |
| A D | Kconfig | 14 # Use SPI or SATA flash erase block size of 4 KiB
|
| /u-boot/arch/arm/mach-tegra/tegra186/ |
| A D | Kconfig | 16 micro-B port, Ethernet, USB3 host port, SATA, PCIe, and two GPIO
|