1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * (C) Copyright 2007
4 * Michael Schwingen, <michael@schwingen.org>
5 *
6 * based in great part on jedec_probe.c from linux kernel:
7 * (C) 2000 Red Hat. GPL'd.
8 * Occasionally maintained by Thayne Harbaugh tharbaugh at lnxi dot com
9 */
10
11 /* The DEBUG define must be before common to enable debugging */
12 /*#define DEBUG*/
13
14 #include <common.h>
15 #include <flash.h>
16 #include <log.h>
17 #include <asm/processor.h>
18 #include <asm/io.h>
19 #include <asm/byteorder.h>
20
21 #define P_ID_AMD_STD CFI_CMDSET_AMD_LEGACY
22
23 /* AMD */
24 #define AM29DL800BB 0x22CB
25 #define AM29DL800BT 0x224A
26
27 #define AM29F400BB 0x22AB
28 #define AM29F800BB 0x2258
29 #define AM29F800BT 0x22D6
30 #define AM29LV400BB 0x22BA
31 #define AM29LV400BT 0x22B9
32 #define AM29LV800BB 0x225B
33 #define AM29LV800BT 0x22DA
34 #define AM29LV160DT 0x22C4
35 #define AM29LV160DB 0x2249
36 #define AM29F017D 0x003D
37 #define AM29F016D 0x00AD
38 #define AM29F080 0x00D5
39 #define AM29F040 0x00A4
40 #define AM29LV040B 0x004F
41 #define AM29F032B 0x0041
42 #define AM29F002T 0x00B0
43
44 /* SST */
45 #define SST39LF800 0x2781
46 #define SST39LF160 0x2782
47 #define SST39VF1601 0x234b
48 #define SST39LF512 0x00D4
49 #define SST39LF010 0x00D5
50 #define SST39LF020 0x00D6
51 #define SST39LF040 0x00D7
52 #define SST39SF010A 0x00B5
53 #define SST39SF020A 0x00B6
54
55 /* STM */
56 #define STM29F400BB 0x00D6
57
58 /* MXIC */
59 #define MX29LV040 0x004F
60
61 /* WINBOND */
62 #define W39L040A 0x00D6
63
64 /* AMIC */
65 #define A29L040 0x0092
66
67 /* EON */
68 #define EN29LV040A 0x004F
69
70 /*
71 * Unlock address sets for AMD command sets.
72 * Intel command sets use the MTD_UADDR_UNNECESSARY.
73 * Each identifier, except MTD_UADDR_UNNECESSARY, and
74 * MTD_UADDR_NO_SUPPORT must be defined below in unlock_addrs[].
75 * MTD_UADDR_NOT_SUPPORTED must be 0 so that structure
76 * initialization need not require initializing all of the
77 * unlock addresses for all bit widths.
78 */
79 enum uaddr {
80 MTD_UADDR_NOT_SUPPORTED = 0, /* data width not supported */
81 MTD_UADDR_0x0555_0x02AA,
82 MTD_UADDR_0x0555_0x0AAA,
83 MTD_UADDR_0x5555_0x2AAA,
84 MTD_UADDR_0x0AAA_0x0555,
85 MTD_UADDR_DONT_CARE, /* Requires an arbitrary address */
86 MTD_UADDR_UNNECESSARY, /* Does not require any address */
87 };
88
89
90 struct unlock_addr {
91 u32 addr1;
92 u32 addr2;
93 };
94
95
96 /*
97 * I don't like the fact that the first entry in unlock_addrs[]
98 * exists, but is for MTD_UADDR_NOT_SUPPORTED - and, therefore,
99 * should not be used. The problem is that structures with
100 * initializers have extra fields initialized to 0. It is _very_
101 * desireable to have the unlock address entries for unsupported
102 * data widths automatically initialized - that means that
103 * MTD_UADDR_NOT_SUPPORTED must be 0 and the first entry here
104 * must go unused.
105 */
106 static const struct unlock_addr unlock_addrs[] = {
107 [MTD_UADDR_NOT_SUPPORTED] = {
108 .addr1 = 0xffff,
109 .addr2 = 0xffff
110 },
111
112 [MTD_UADDR_0x0555_0x02AA] = {
113 .addr1 = 0x0555,
114 .addr2 = 0x02aa
115 },
116
117 [MTD_UADDR_0x0555_0x0AAA] = {
118 .addr1 = 0x0555,
119 .addr2 = 0x0aaa
120 },
121
122 [MTD_UADDR_0x5555_0x2AAA] = {
123 .addr1 = 0x5555,
124 .addr2 = 0x2aaa
125 },
126
127 [MTD_UADDR_0x0AAA_0x0555] = {
128 .addr1 = 0x0AAA,
129 .addr2 = 0x0555
130 },
131
132 [MTD_UADDR_DONT_CARE] = {
133 .addr1 = 0x0000, /* Doesn't matter which address */
134 .addr2 = 0x0000 /* is used - must be last entry */
135 },
136
137 [MTD_UADDR_UNNECESSARY] = {
138 .addr1 = 0x0000,
139 .addr2 = 0x0000
140 }
141 };
142
143
144 struct amd_flash_info {
145 const __u16 mfr_id;
146 const __u16 dev_id;
147 const char *name;
148 const int DevSize;
149 const int NumEraseRegions;
150 const int CmdSet;
151 const __u8 uaddr[4]; /* unlock addrs for 8, 16, 32, 64 */
152 const ulong regions[6];
153 };
154
155 #define ERASEINFO(size,blocks) (size<<8)|(blocks-1)
156
157 #define SIZE_64KiB 16
158 #define SIZE_128KiB 17
159 #define SIZE_256KiB 18
160 #define SIZE_512KiB 19
161 #define SIZE_1MiB 20
162 #define SIZE_2MiB 21
163 #define SIZE_4MiB 22
164 #define SIZE_8MiB 23
165
166 static const struct amd_flash_info jedec_table[] = {
167 #ifdef CONFIG_SYS_FLASH_LEGACY_256Kx8
168 {
169 .mfr_id = (u16)SST_MANUFACT,
170 .dev_id = SST39LF020,
171 .name = "SST 39LF020",
172 .uaddr = {
173 [0] = MTD_UADDR_0x5555_0x2AAA /* x8 */
174 },
175 .DevSize = SIZE_256KiB,
176 .CmdSet = P_ID_AMD_STD,
177 .NumEraseRegions= 1,
178 .regions = {
179 ERASEINFO(0x01000,64),
180 }
181 },
182 #endif
183 #ifdef CONFIG_SYS_FLASH_LEGACY_512Kx8
184 {
185 .mfr_id = (u16)AMD_MANUFACT,
186 .dev_id = AM29LV040B,
187 .name = "AMD AM29LV040B",
188 .uaddr = {
189 [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
190 },
191 .DevSize = SIZE_512KiB,
192 .CmdSet = P_ID_AMD_STD,
193 .NumEraseRegions= 1,
194 .regions = {
195 ERASEINFO(0x10000,8),
196 }
197 },
198 {
199 .mfr_id = (u16)SST_MANUFACT,
200 .dev_id = SST39LF040,
201 .name = "SST 39LF040",
202 .uaddr = {
203 [0] = MTD_UADDR_0x5555_0x2AAA /* x8 */
204 },
205 .DevSize = SIZE_512KiB,
206 .CmdSet = P_ID_AMD_STD,
207 .NumEraseRegions= 1,
208 .regions = {
209 ERASEINFO(0x01000,128),
210 }
211 },
212 {
213 .mfr_id = (u16)STM_MANUFACT,
214 .dev_id = STM_ID_M29W040B,
215 .name = "ST Micro M29W040B",
216 .uaddr = {
217 [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
218 },
219 .DevSize = SIZE_512KiB,
220 .CmdSet = P_ID_AMD_STD,
221 .NumEraseRegions= 1,
222 .regions = {
223 ERASEINFO(0x10000,8),
224 }
225 },
226 {
227 .mfr_id = (u16)MX_MANUFACT,
228 .dev_id = MX29LV040,
229 .name = "MXIC MX29LV040",
230 .uaddr = {
231 [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
232 },
233 .DevSize = SIZE_512KiB,
234 .CmdSet = P_ID_AMD_STD,
235 .NumEraseRegions= 1,
236 .regions = {
237 ERASEINFO(0x10000, 8),
238 }
239 },
240 {
241 .mfr_id = (u16)WINB_MANUFACT,
242 .dev_id = W39L040A,
243 .name = "WINBOND W39L040A",
244 .uaddr = {
245 [0] = MTD_UADDR_0x5555_0x2AAA /* x8 */
246 },
247 .DevSize = SIZE_512KiB,
248 .CmdSet = P_ID_AMD_STD,
249 .NumEraseRegions= 1,
250 .regions = {
251 ERASEINFO(0x10000, 8),
252 }
253 },
254 {
255 .mfr_id = (u16)AMIC_MANUFACT,
256 .dev_id = A29L040,
257 .name = "AMIC A29L040",
258 .uaddr = {
259 [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
260 },
261 .DevSize = SIZE_512KiB,
262 .CmdSet = P_ID_AMD_STD,
263 .NumEraseRegions= 1,
264 .regions = {
265 ERASEINFO(0x10000, 8),
266 }
267 },
268 {
269 .mfr_id = (u16)EON_MANUFACT,
270 .dev_id = EN29LV040A,
271 .name = "EON EN29LV040A",
272 .uaddr = {
273 [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
274 },
275 .DevSize = SIZE_512KiB,
276 .CmdSet = P_ID_AMD_STD,
277 .NumEraseRegions= 1,
278 .regions = {
279 ERASEINFO(0x10000, 8),
280 }
281 },
282 #endif
283 #ifdef CONFIG_SYS_FLASH_LEGACY_512Kx16
284 {
285 .mfr_id = (u16)AMD_MANUFACT,
286 .dev_id = AM29F400BB,
287 .name = "AMD AM29F400BB",
288 .uaddr = {
289 [1] = MTD_UADDR_0x0555_0x02AA /* x16 */
290 },
291 .DevSize = SIZE_512KiB,
292 .CmdSet = CFI_CMDSET_AMD_LEGACY,
293 .NumEraseRegions= 4,
294 .regions = {
295 ERASEINFO(0x04000, 1),
296 ERASEINFO(0x02000, 2),
297 ERASEINFO(0x08000, 1),
298 ERASEINFO(0x10000, 7),
299 }
300 },
301 {
302 .mfr_id = (u16)AMD_MANUFACT,
303 .dev_id = AM29LV400BB,
304 .name = "AMD AM29LV400BB",
305 .uaddr = {
306 [1] = MTD_UADDR_0x0555_0x02AA /* x16 */
307 },
308 .DevSize = SIZE_512KiB,
309 .CmdSet = CFI_CMDSET_AMD_LEGACY,
310 .NumEraseRegions= 4,
311 .regions = {
312 ERASEINFO(0x04000,1),
313 ERASEINFO(0x02000,2),
314 ERASEINFO(0x08000,1),
315 ERASEINFO(0x10000,7),
316 }
317 },
318 {
319 .mfr_id = (u16)AMD_MANUFACT,
320 .dev_id = AM29LV800BB,
321 .name = "AMD AM29LV800BB",
322 .uaddr = {
323 [1] = MTD_UADDR_0x0555_0x02AA /* x16 */
324 },
325 .DevSize = SIZE_1MiB,
326 .CmdSet = CFI_CMDSET_AMD_LEGACY,
327 .NumEraseRegions= 4,
328 .regions = {
329 ERASEINFO(0x04000, 1),
330 ERASEINFO(0x02000, 2),
331 ERASEINFO(0x08000, 1),
332 ERASEINFO(0x10000, 15),
333 }
334 },
335 {
336 .mfr_id = (u16)AMD_MANUFACT,
337 .dev_id = AM29LV800BT,
338 .name = "AMD AM29LV800BT",
339 .uaddr = {
340 [1] = MTD_UADDR_0x0555_0x02AA /* x16 */
341 },
342 .DevSize = SIZE_1MiB,
343 .CmdSet = CFI_CMDSET_AMD_LEGACY,
344 .NumEraseRegions= 4,
345 .regions = {
346 ERASEINFO(0x10000, 15),
347 ERASEINFO(0x08000, 1),
348 ERASEINFO(0x02000, 2),
349 ERASEINFO(0x04000, 1),
350 }
351 },
352 {
353 .mfr_id = (u16)MX_MANUFACT,
354 .dev_id = AM29LV800BT,
355 .name = "MXIC MX29LV800BT",
356 .uaddr = {
357 [1] = MTD_UADDR_0x0555_0x02AA /* x16 */
358 },
359 .DevSize = SIZE_1MiB,
360 .CmdSet = CFI_CMDSET_AMD_LEGACY,
361 .NumEraseRegions= 4,
362 .regions = {
363 ERASEINFO(0x10000, 15),
364 ERASEINFO(0x08000, 1),
365 ERASEINFO(0x02000, 2),
366 ERASEINFO(0x04000, 1),
367 }
368 },
369 {
370 .mfr_id = (u16)EON_ALT_MANU,
371 .dev_id = AM29LV800BT,
372 .name = "EON EN29LV800BT",
373 .uaddr = {
374 [1] = MTD_UADDR_0x0555_0x02AA /* x16 */
375 },
376 .DevSize = SIZE_1MiB,
377 .CmdSet = CFI_CMDSET_AMD_LEGACY,
378 .NumEraseRegions= 4,
379 .regions = {
380 ERASEINFO(0x10000, 15),
381 ERASEINFO(0x08000, 1),
382 ERASEINFO(0x02000, 2),
383 ERASEINFO(0x04000, 1),
384 }
385 },
386 {
387 .mfr_id = (u16)STM_MANUFACT,
388 .dev_id = STM29F400BB,
389 .name = "ST Micro M29F400BB",
390 .uaddr = {
391 [1] = MTD_UADDR_0x0555_0x02AA /* x16 */
392 },
393 .DevSize = SIZE_512KiB,
394 .CmdSet = CFI_CMDSET_AMD_LEGACY,
395 .NumEraseRegions = 4,
396 .regions = {
397 ERASEINFO(0x04000, 1),
398 ERASEINFO(0x02000, 2),
399 ERASEINFO(0x08000, 1),
400 ERASEINFO(0x10000, 7),
401 }
402 },
403 #endif
404 };
405
fill_info(flash_info_t * info,const struct amd_flash_info * jedec_entry,ulong base)406 static inline void fill_info(flash_info_t *info, const struct amd_flash_info *jedec_entry, ulong base)
407 {
408 int i,j;
409 int sect_cnt;
410 int size_ratio;
411 int total_size;
412 enum uaddr uaddr_idx;
413
414 size_ratio = info->portwidth / info->chipwidth;
415
416 debug("Found JEDEC Flash: %s\n", jedec_entry->name);
417 info->vendor = jedec_entry->CmdSet;
418 /* Todo: do we need device-specific timeouts? */
419 info->erase_blk_tout = 30000;
420 info->buffer_write_tout = 1000;
421 info->write_tout = 100;
422 info->name = jedec_entry->name;
423
424 /* copy unlock addresses from device table to CFI info struct. This
425 is just here because the addresses are in the table anyway - if
426 the flash is not detected due to wrong unlock addresses,
427 flash_detect_legacy would have to try all of them before we even
428 get here. */
429 switch(info->chipwidth) {
430 case FLASH_CFI_8BIT:
431 uaddr_idx = jedec_entry->uaddr[0];
432 break;
433 case FLASH_CFI_16BIT:
434 uaddr_idx = jedec_entry->uaddr[1];
435 break;
436 case FLASH_CFI_32BIT:
437 uaddr_idx = jedec_entry->uaddr[2];
438 break;
439 default:
440 uaddr_idx = MTD_UADDR_NOT_SUPPORTED;
441 break;
442 }
443
444 debug("unlock address index %d\n", uaddr_idx);
445 info->addr_unlock1 = unlock_addrs[uaddr_idx].addr1;
446 info->addr_unlock2 = unlock_addrs[uaddr_idx].addr2;
447 debug("unlock addresses are 0x%lx/0x%lx\n",
448 info->addr_unlock1, info->addr_unlock2);
449
450 sect_cnt = 0;
451 total_size = 0;
452 for (i = 0; i < jedec_entry->NumEraseRegions; i++) {
453 ulong erase_region_size = jedec_entry->regions[i] >> 8;
454 ulong erase_region_count = (jedec_entry->regions[i] & 0xff) + 1;
455
456 total_size += erase_region_size * erase_region_count;
457 debug("erase_region_count = %ld erase_region_size = %ld\n",
458 erase_region_count, erase_region_size);
459 for (j = 0; j < erase_region_count; j++) {
460 if (sect_cnt >= CONFIG_SYS_MAX_FLASH_SECT) {
461 printf("ERROR: too many flash sectors\n");
462 break;
463 }
464 info->start[sect_cnt] = base;
465 base += (erase_region_size * size_ratio);
466 sect_cnt++;
467 }
468 }
469 info->sector_count = sect_cnt;
470 info->size = total_size * size_ratio;
471 }
472
473 /*-----------------------------------------------------------------------
474 * match jedec ids against table. If a match is found, fill flash_info entry
475 */
jedec_flash_match(flash_info_t * info,ulong base)476 int jedec_flash_match(flash_info_t *info, ulong base)
477 {
478 int ret = 0;
479 int i;
480 ulong mask = 0xFFFF;
481 if (info->chipwidth == 1)
482 mask = 0xFF;
483
484 for (i = 0; i < ARRAY_SIZE(jedec_table); i++) {
485 if ((jedec_table[i].mfr_id & mask) == (info->manufacturer_id & mask) &&
486 (jedec_table[i].dev_id & mask) == (info->device_id & mask)) {
487 fill_info(info, &jedec_table[i], base);
488 ret = 1;
489 break;
490 }
491 }
492 return ret;
493 }
494