Searched refs:SW4 (Results 1 – 14 of 14) sorted by relevance
| /u-boot/board/freescale/p1010rdb/ |
| A D | README.P1010RDB-PB | 67 SW4[1:4]= 1010
73 SW4[1:4]= 1111 and SW3[3:4]= 00 for 16bit NOR boot
74 SW4[1:4]= 1010 and SW3[3:4]= 01 for 8bit NAND boot
75 SW4[1:4]= 0110 and SW3[3:4]= 00 for SPI boot
76 SW4[1:4]= 0111 and SW3[3:4]= 10 for SD boot
152 set SW1[8]=0, SW4[1:4]= 1111 and SW3[3:4]= 00, then power on the board
156 set SW1[8]=1, SW4[1:4]= 1111 and SW3[3:4]= 00, then power on the board
161 Set SW4[1:4]= 1010 and SW3[3:4]= 01, then power on the board
167 set SW4[1:4]= 0110 and SW3[3:4]= 00, then power on the board
174 set SW4[1:4]= 0111 and SW3[3:4]= 10, then power on the board
|
| A D | README.P1010RDB-PA | 82 SW4[1:4]= 1111 and SW6[4]=0 for boot from 16bit NOR flash
83 SW4[1:4]= 1000 and SW6[4]=1 for boot from 8bit NAND flash
84 SW4[1:4]= 0110 and SW6[4]=0 for boot from SPI flash
110 3. Check SW4[1:4]= 1111 and SW6[4]=0, then power on.
145 3. Check SW4[1:4]= 1000 and SW6[4]=1, then power on.
164 3. Check SW4[1:4]= 0110 and SW6[4]=0, then power on.
|
| /u-boot/board/freescale/common/ |
| A D | mc34vr500.c | 31 if (sw > SW4) { in mc34vr500_get_sw_volt()
70 if (sw > SW4 || sw_volt < 625) in mc34vr500_set_sw_volt()
|
| /u-boot/board/freescale/ls1046ardb/ |
| A D | ls1046ardb.c | 114 return mc34vr500_get_sw_volt(SW4); in get_serdes_volt()
119 return mc34vr500_set_sw_volt(SW4, svdd); in set_serdes_volt()
|
| /u-boot/board/freescale/ls1088a/ |
| A D | README | 19 SW4 1001 0011
26 SW4 1001 0011
33 SW4 1001 0011
94 SW4 0010 0000
|
| /u-boot/board/myir/mys_6ulx/ |
| A D | README | 23 SW4 -> 1
48 SW4 -> 1
|
| /u-boot/include/power/ |
| A D | mc34vr500_pmic.h | 168 SW4, enumerator
|
| /u-boot/board/freescale/mpc837xemds/ |
| A D | README | 17 SW4[8] is the bit labeled 8 on Switch 4.
27 SW4[1-8]= 0000_0110 (core PLL setting)
|
| /u-boot/doc/ |
| A D | README.mpc85xxcds | 135 SW4=10001000
160 SW4=11111110
174 SW4=11110011
|
| /u-boot/board/freescale/mpc832xemds/ |
| A D | README | 18 SW4[8] is the bit labeled 8 on Switch 4.
29 SW4[1-8]= 0001_0010 (Flash boot on local bus, system PLL setting)
|
| /u-boot/arch/arm/dts/ |
| A D | salvator-common.dtsi | 121 label = "SW4-1";
128 label = "SW4-2";
135 label = "SW4-3";
142 label = "SW4-4";
|
| A D | r8a7794-silk.dts | 59 label = "SW4";
|
| /u-boot/board/freescale/ls1028a/ |
| A D | README | 87 SW4 : 0000_0000
99 SW4 : 0000_0000
|
| /u-boot/board/sbc8548/ |
| A D | README | 237 SW4 settings are readable from the EPLD and are currently not used for
|
Completed in 10 milliseconds