Searched refs:adapter (Results 1 – 25 of 26) sorted by relevance
12
| /u-boot/doc/ |
| A D | README.usb | 64 CONFIG_USB_HOST_ETHER enables USB ethernet adapter support
70 If you have a supported USB Ethernet adapter you can use it in U-Boot
74 client. In that case your board is pretending to be an Ethernet adapter
79 Ethernet adapter to which it is directly connected and the connection to
80 the outside world is your adapter's Ethernet cable. Your board becomes an
99 supported device list, so we know this adapter is supported.
103 If your adapter is not listed there is a still a chance that it will
104 work. Try looking up the manufacturer of the chip inside your adapter.
105 or take the adapter apart and look for chip markings. Then add a line
108 between the chip in your adapter and the driver. You could try to get a
[all …]
|
| A D | README.odroid | 94 If you have an eMMC->microSD adapter you can prepare the card as in point 5.
169 The adapter does not come with a preconfigured MAC address, and hence it needs
|
| A D | README.pxe | 36 ethaddr - this is the standard MAC address for the ethernet adapter in use.
|
| /u-boot/board/congatec/conga-qeval20-qa3-e3845/ |
| A D | README | 21 RS232 level shifters. So a TTL-USB UART adapter does not work in
23 RS232 level signals of the PC UART via some adapter cable.
|
| /u-boot/board/toradex/common/ |
| A D | Kconfig | 81 bool "Support for additional EEPROMs (carrier board, display adapter)"
85 adapter EEPROMs.
|
| /u-boot/board/warp/ |
| A D | README | 20 Connect a USB to serial adapter between the host PC and warp
|
| /u-boot/include/ |
| A D | i2c.h | 677 int adapter; member
683 #define I2C_ADAPTER(bus) i2c_bus[bus].adapter
|
| /u-boot/board/warp7/ |
| A D | README | 27 Connect a USB to serial adapter between the host PC and warp7
|
| /u-boot/board/freescale/ls1043aqds/ |
| A D | README | 33 - SDHC port connects directly to an adapter card slot, featuring:
|
| /u-boot/drivers/net/ |
| A D | e1000.h | 1852 #define TBI_ACCEPT(adapter, status, errors, length, last_byte) \ argument
1853 ((adapter)->tbi_compatibility_on && \
1857 (((length) > ((adapter)->min_frame_size - VLAN_TAG_SIZE)) && \
1858 ((length) <= ((adapter)->max_frame_size + 1))) : \
1859 (((length) > (adapter)->min_frame_size) && \
1860 ((length) <= ((adapter)->max_frame_size + VLAN_TAG_SIZE + 1)))))
|
| A D | Kconfig | 211 adapters. For more information on how to identify your adapter, go
214 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
|
| /u-boot/board/technexion/pico-imx6/ |
| A D | README | 25 Connect a USB to serial adapter between the host PC and pico.
|
| /u-boot/board/freescale/ls1046aqds/ |
| A D | README | 33 - SDHC port connects directly to an adapter card slot, featuring:
|
| /u-boot/doc/board/emulation/ |
| A D | qemu-arm.rst | 70 - To add an Intel E1000 network adapter, pass e.g.::
|
| /u-boot/arch/arm/dts/ |
| A D | sun8i-h2-plus-orangepi-r1.dts | 81 * RTL8152B USB-Ethernet adapter is connected to USB1,
|
| A D | sun4i-a10-gemei-g9.dts | 71 * Touchscreen - gt801_2plus1 @ i2c adapter 2 @ 0x48
|
| A D | imx8mm-verdin.dts | 388 /* EEPROM on display adapter (MIPI DSI Display Adapter) */
|
| A D | rk3399-pinebook-pro.dts | 304 /* M.2 adapter power, switched by vcc1v8_s3 */
|
| /u-boot/drivers/mtd/spi/ |
| A D | Kconfig | 201 Enable the MTD support for spi flash layer, this adapter is for
204 flash subsystem. Such an adapter is needed for subsystems like
|
| /u-boot/board/freescale/ls2080ardb/ |
| A D | README | 36 - SDHC adapter
|
| /u-boot/board/technexion/pico-imx6ul/ |
| A D | README | 28 Connect a USB to serial adapter between the host PC and pico.
|
| /u-boot/board/technexion/pico-imx7d/ |
| A D | README | 25 Connect a USB to serial adapter between the host PC and pico.
|
| /u-boot/doc/uefi/ |
| A D | uefi.rst | 64 or the network adapter and the file name of the most recently loaded PE-COFF
405 * network adapter
|
| /u-boot/drivers/usb/gadget/ |
| A D | Kconfig | 131 such as an AC adapter or batteries.
|
| /u-boot/scripts/ |
| A D | spelling.txt | 53 adapater||adapter
|
Completed in 30 milliseconds
12