| /u-boot/drivers/serial/ |
| A D | serial_mtk.c | 70 #define BAUD_ALLOW_MAX(baud) ((baud) + (baud) * 3 / 100) argument
71 #define BAUD_ALLOW_MIX(baud) ((baud) - (baud) * 3 / 100) argument
88 if (baud <= 115200) { in _mtk_serial_setbrg()
99 quot * baud); in _mtk_serial_setbrg()
102 if ((realbaud > BAUD_ALLOW_MAX(baud)) || in _mtk_serial_setbrg()
103 (realbaud < BAUD_ALLOW_MIX(baud))) { in _mtk_serial_setbrg()
105 baud); in _mtk_serial_setbrg()
111 } else if (baud <= 576000) { in _mtk_serial_setbrg()
115 if ((baud == 500000) || (baud == 576000)) in _mtk_serial_setbrg()
116 baud = 460800; in _mtk_serial_setbrg()
[all …]
|
| A D | serial_zynq.c | 50 unsigned long clock, unsigned long baud) in _uart_zynq_serial_setbrg() argument
57 if (clock < 1000000 && baud > 4800) in _uart_zynq_serial_setbrg()
58 baud = 4800; in _uart_zynq_serial_setbrg()
67 bgen = clock / (baud * (bdiv + 1)); in _uart_zynq_serial_setbrg()
77 if (baud > calc_baud) in _uart_zynq_serial_setbrg()
78 calc_bauderror = baud - calc_baud; in _uart_zynq_serial_setbrg()
80 calc_bauderror = calc_baud - baud; in _uart_zynq_serial_setbrg()
81 if (((calc_bauderror * 100) / baud) < 3) in _uart_zynq_serial_setbrg()
|
| A D | serial_cortina.c | 68 unsigned int uart_ctrl, baud, sample; in ca_serial_setbrg() local
70 baud = CORTINA_UART_CLOCK / baudrate; in ca_serial_setbrg()
74 uart_ctrl |= UCFG_BAUD_COUNT(baud); in ca_serial_setbrg()
77 sample = baud / 2; in ca_serial_setbrg()
|
| A D | serial_ar933x.c | 59 static void ar933x_serial_get_scale_step(u32 clk, u32 baud, in ar933x_serial_get_scale_step() argument
68 min_diff = baud; in ar933x_serial_get_scale_step()
73 tstep = baud * (tscale + 1); in ar933x_serial_get_scale_step()
81 diff = abs(baudrate - baud); in ar933x_serial_get_scale_step()
|
| A D | serial_bcm283x_mu.c | 40 u32 baud; member
69 writel(divider - 1, ®s->baud); in bcm283x_mu_serial_setbrg()
|
| A D | serial_sifive.c | 72 unsigned long clock, unsigned long baud) in _sifive_serial_setbrg() argument
74 writel((uart_min_clk_divisor(clock, baud)), ®s->div); in _sifive_serial_setbrg()
|
| A D | serial_mt7620.c | 74 static void _mt7620_serial_setbrg(struct mt7620_serial_plat *plat, int baud) in _mt7620_serial_setbrg() argument
79 quot = DIV_ROUND_CLOSEST(plat->clock, 16 * baud); in _mt7620_serial_setbrg()
|
| A D | serial_lpuart.c | 288 tmp = in_le32(&base->baud); in _lpuart32_serial_setbrg_7ulp()
302 out_le32(&base->baud, tmp); in _lpuart32_serial_setbrg_7ulp()
325 lpuart_write32(plat->flags, &base->baud, sbr); in _lpuart32_serial_setbrg()
|
| /u-boot/doc/usage/ |
| A D | loady.rst | 11 loady [addr [baud]]
25 baud
26 baud rate for the ymodem transmission. After the transmission the baud
|
| /u-boot/doc/device-tree-bindings/serial/ |
| A D | bcm2835-aux-uart.txt | 6 - clock: input clock frequency for the UART (used to calculate the baud
10 - skip-init: if present, the baud rate divisor is not changed
|
| A D | pl01x.txt | 6 - clock: input clock frequency for the UART (used to calculate the baud
10 - skip-init: if present, the baud rate divisor is not changed
|
| /u-boot/arch/mips/dts/ |
| A D | jz4780.dtsi | 78 clock-names = "baud", "module";
92 clock-names = "baud", "module";
106 clock-names = "baud", "module";
120 clock-names = "baud", "module";
134 clock-names = "baud", "module";
|
| /u-boot/include/ |
| A D | fsl_lpuart.h | 14 u32 baud; member
25 u32 baud; member
|
| /u-boot/board/astro/mcf5373l/ |
| A D | astro.h | 5 int rs_serial_init(int port, int baud);
|
| A D | mcf5373l.c | 92 int rs_serial_init(int port, int baud) in rs_serial_init() argument
129 counter = (u32) (gd->bus_clk / (baud)); in rs_serial_init()
|
| /u-boot/arch/x86/include/asm/arch-slimbootloader/ |
| A D | slimbootloader.h | 88 u32 baud; member
|
| /u-boot/arch/x86/cpu/slimbootloader/ |
| A D | serial.c | 35 data->baud, in slimbootloader_serial_of_to_plat()
|
| /u-boot/arch/x86/include/asm/acpi/ |
| A D | debug.asl | 32 Store(0x01, CDAT) /* 115200 baud (low) */
33 Store(0x00, CDLM) /* 115200 baud (high) */
|
| /u-boot/arch/x86/cpu/baytrail/ |
| A D | Kconfig | 34 A maximum baud rate of 115200 bps is supported. For this
|
| /u-boot/doc/ |
| A D | README.AMCC-eval-boards-cleanup | 11 o Use 115200 baud as default console baudrate.
|
| A D | README.vxworks | 77 It's very common that VxWorks BSPs configure a different baud rate for the
79 to use 9600 as the default baud rate on all x86 BSPs while U-Boot uses 115200.
80 Please configure both U-Boot and VxWorks to use the same baud rate, or it may
|
| /u-boot/disk/ |
| A D | part_amiga.h | 135 u32 baud; member
|
| /u-boot/arch/arm/dts/ |
| A D | meson-gxbb.dtsi | 819 clock-names = "xtal", "pclk", "baud";
824 clock-names = "xtal", "pclk", "baud";
829 clock-names = "xtal", "pclk", "baud";
834 clock-names = "xtal", "pclk", "baud";
839 clock-names = "xtal", "pclk", "baud";
|
| A D | mt7623.dtsi | 189 clock-names = "baud", "bus";
200 clock-names = "baud", "bus";
211 clock-names = "baud", "bus";
222 clock-names = "baud", "bus";
|
| A D | mt7629.dtsi | 179 clock-names = "baud", "bus";
192 clock-names = "baud", "bus";
205 clock-names = "baud", "bus";
|