Searched refs:changed (Results 1 – 25 of 66) sorted by relevance
123
| /u-boot/doc/device-tree-bindings/serial/ |
| A D | bcm2835-aux-uart.txt | 10 - skip-init: if present, the baud rate divisor is not changed
|
| A D | pl01x.txt | 10 - skip-init: if present, the baud rate divisor is not changed
|
| /u-boot/tools/patman/test/ |
| A D | 0000-cover-letter.patch | 19 4 files changed, 6 insertions(+), 2 deletions(-)
|
| A D | 0001-pci-Correct-cast-for-sandbox.patch | 33 1 file changed, 2 insertions(+), 1 deletion(-)
|
| A D | 0002-fdt-Correct-cast-for-sandbox-in-fdtdec_setup_mem_siz.patch | 47 3 files changed, 4 insertions(+), 1 deletion(-)
|
| /u-boot/arch/arm/dts/ |
| A D | sun50i-a64-pinephone-1.1.dts | 16 * PWM backlight circuit on this PinePhone revision was changed since
|
| A D | sun50i-a64-pinephone-1.2.dts | 16 * PWM backlight circuit on this PinePhone revision was changed since 1.0,
|
| A D | sun8i-h3-orangepi-pc-plus.dts | 57 /* LEDs changed to active high on the plus */
|
| A D | armada-xp-gp.dts | 42 * of memory available can be changed by the
|
| /u-boot/board/eets/pdu001/ |
| A D | Kconfig | 27 process it can be changed to green (or heartbeat or anything else)
|
| /u-boot/arch/powerpc/cpu/mpc86xx/ |
| A D | Kconfig | 45 if changed by pre-boot regime. The value here must match
|
| /u-boot/drivers/net/phy/ |
| A D | micrel_ksz90x1.c | 116 int i, changed = 0, offset, max; in ksz90x1_of_config_group() local
142 changed = 1; /* Value was changed in OF */ in ksz90x1_of_config_group()
153 if (!changed) in ksz90x1_of_config_group()
|
| A D | phy.c | 43 int err, changed = 0; in genphy_config_advert() local
80 changed = 1; in genphy_config_advert()
92 return changed; in genphy_config_advert()
112 changed = 1; in genphy_config_advert()
118 return changed; in genphy_config_advert()
|
| /u-boot/doc/ |
| A D | README.watchdog | 30 TODO: vision2 is removed now, so perhaps this can be changed.
|
| A D | README.silent | 6 When the "silent" variable is changed with env set, the change
|
| A D | README.mpc85xxcds | 97 Most switches on the carrier board should not be changed. The only
141 Most switches on the CPU Card should not be changed. However, the
142 frequency can be changed by setting SW3:
|
| A D | README.pblimage | 65 PBI instructions. File name must not be changed since they are used
|
| A D | README.440-DDR-performance | 3 spd_sdram.c) are changed accordingly. So all 440er boards using
|
| A D | README.multi-dtb-fit | 33 FIT is uncompressed is dynamicaly allocated but this behaviour can be changed
|
| /u-boot/doc/SPI/ |
| A D | README.ti_qspi_flash | 18 will be changed to qspi boot. Then, the ROM code will read MLO
|
| /u-boot/lib/lzma/ |
| A D | history.txt | 147 - Some GUIDs/interfaces in C++ were changed.
179 - Interfaces for ANSI-C LZMA Decoder (LzmaDecode.c) were changed
|
| /u-boot/board/buffalo/lsxl/ |
| A D | README | 13 In u-boot v2019.07 the driver for the SATA port was changed to a new
15 supported anymore. More important, the boot commands have changed. You have
|
| /u-boot/scripts/ |
| A D | Kbuild.include | 231 # target, or command line has changed
258 # Execute command if command has changed or prerequisite(s) are updated.
274 # Will check if $(cmd_foo) or any of the prerequisites changed,
|
| /u-boot/board/logicpd/imx6/ |
| A D | README | 30 bootROM and it cannot be changed. The following instructions assume the SD
|
| /u-boot/board/cobra5272/bdm/ |
| A D | cobra5272_uboot.gdb | 7 # This file was changed to suite the senTec COBRA5272 board.
|
Completed in 16 milliseconds
123