Searched refs:down (Results 1 – 25 of 174) sorted by relevance
1234567
| /u-boot/doc/ |
| A D | README.t1040-l2switch | 53 0 enabled down 10 half
54 1 enabled down 10 half
55 2 enabled down 10 half
57 4 disabled down - half
58 5 disabled down - half
59 6 disabled down - half
60 7 disabled down - half
|
| /u-boot/doc/device-tree-bindings/misc/ |
| A D | intel,baytrail-fsp.txt | 41 - fsp,enable-memory-down
43 If you set "fsp,enable-memory-down" you are strongly encouraged to provide an
44 "fsp,memory-down-params{};" to specify how your memory is configured. If you
45 do not set "fsp,enable-memory-down", then the DIMM SPD information will be
66 - fsp,memory-down-params {
134 fsp,enable-memory-down;
135 fsp,memory-down-params {
|
| /u-boot/doc/device-tree-bindings/clock/ |
| A D | rockchip,rk3288-dmc.txt | 24 …lock frequency high than pd-enable-freq,this driver should enable the automatic power down function
26 …down-cnt: Power-down idle period. Memories are placed into power-down mode if the NIF is idle for …
140 rockchip,auto-power-down-cnt = <64>;
|
| /u-boot/doc/device-tree-bindings/video/ |
| A D | intel-gma.txt | 19 - intel,panel-power-down-delay : T3 time sequence
35 intel,panel-power-down-delay = <500>;
|
| /u-boot/drivers/ram/sifive/ |
| A D | fu540_ddr.c | 156 u32 down, up; in fu540_ddr_check_errata() local
169 down = (updownreg >> in fu540_ddr_check_errata()
175 failc0 = ((down == 0) && (up == 0x3F)); in fu540_ddr_check_errata()
176 failc1 = ((up == 0) && (down == 0x3F)); in fu540_ddr_check_errata()
|
| /u-boot/board/freescale/t208xrdb/ |
| A D | t2080_pbi.cfg | 32 #Errata for slowing down the MDC clock to make it <= 2.5 MHZ
|
| /u-boot/board/freescale/t208xqds/ |
| A D | t208x_pbi.cfg | 32 #Errata for slowing down the MDC clock to make it <= 2.5 MHZ
|
| /u-boot/arch/arm/dts/ |
| A D | imx6qdl-sr-som.dtsi | 95 /* AR8035 pin strapping: PHYADDR#0: pull down */
97 /* AR8035 pin strapping: PHYADDR#1: pull down */
103 /* AR8035 pin strapping: MODE#0: pull down */
|
| A D | rk3399-gru-chromebook.dtsi | 76 min-slew-down-rate = <225>;
219 min-slew-down-rate = <225>;
224 min-slew-down-rate = <225>;
229 min-slew-down-rate = <225>;
|
| A D | rk3308.dtsi | 759 pcfg_pull_down: pcfg-pull-down {
760 bias-pull-down;
787 pcfg_pull_down_4ma: pcfg-pull-down-4ma {
788 bias-pull-down;
1637 pwm0_pin_pull_down: pwm0-pin-pull-down {
1649 pwm1_pin_pull_down: pwm1-pin-pull-down {
1661 pwm2_pin_pull_down: pwm2-pin-pull-down {
1673 pwm3_pin_pull_down: pwm3-pin-pull-down {
1685 pwm4_pin_pull_down: pwm4-pin-pull-down {
1697 pwm5_pin_pull_down: pwm5-pin-pull-down {
[all …]
|
| A D | mt7622-bananapi-bpi-r64.dts | 137 bias-pull-down;
161 bias-pull-down;
|
| A D | mt7622-rfb.dts | 130 bias-pull-down;
154 bias-pull-down;
|
| A D | sun4i-a10-inet9f-rev03.dts | 94 left-joystick-down {
126 right-joystick-down {
158 dpad-down {
331 bias-pull-down;
|
| A D | mt8518-ap1-emmc.dts | 79 bias-pull-down;
|
| A D | rk3399-puma-haikou-u-boot.dtsi | 36 * eMMC and SPI flash powered-down initially (in fact it keeps the
|
| A D | rk3308-evb.dts | 58 vol-down-key {
60 label = "volume down";
|
| A D | meson-gxbb-p200.dts | 48 button-down {
|
| /u-boot/board/nvidia/nyan-big/ |
| A D | README | 13 Connect a servo board. Then with t20_rec and warn_rst held down:
|
| /u-boot/arch/arm/mach-tegra/ |
| A D | Kconfig | 158 the tool. Unfortunately, these tools do not shut down the USB
160 does not "de-enumerate" the USB device. This option shuts down the
180 typically entered by holding down a "force recovery" button and
|
| /u-boot/doc/device-tree-bindings/gpio/ |
| A D | gpio-samsung.txt | 14 [flags and pull up/down]
|
| A D | intel,x86-pinctrl.txt | 22 - pull-assign - (optional) this set the pull assignement (up/down) of the pin
|
| /u-boot/doc/device-tree-bindings/spi/ |
| A D | soft-spi.txt | 4 SPI bus. No SPI host is required for this to work. The down-side is that the
|
| /u-boot/doc/device-tree-bindings/pinctrl/ |
| A D | kendryte,k210-fpioa.txt | 38 bias-disable, bias-pull-down, bias-pull-up, drive-strength,
47 - bias-pull-up, -down, and -pin-default: The pull strength cannot be configured.
|
| A D | atmel,at91-pio4-pinctrl.txt | 29 bias-pull-down, bias-pull-up, drive-open-drain, input-schmitt-enable,
|
| /u-boot/doc/device-tree-bindings/input/ |
| A D | adc-keys.txt | 44 button-down {
|
Completed in 23 milliseconds
1234567