Searched refs:slow (Results 1 – 25 of 51) sorted by relevance
123
| /u-boot/board/freescale/corenet_ds/ |
| A D | pbi.cfg | 24 #Initialize eSPI controller, default configuration is slow for eSPI to
|
| /u-boot/board/varisys/cyrus/ |
| A D | pbi.cfg | 26 #Initialize eSPI controller, default configuration is slow for eSPI to
|
| /u-boot/arch/arm/dts/ |
| A D | kirkwood-is2.dts | 30 slow-gpio = <&gpio0 29 0>;
|
| A D | kirkwood-ns2.dts | 30 slow-gpio = <&gpio0 29 0>;
|
| A D | kirkwood-d2net.dts | 28 slow-gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
|
| A D | kirkwood-ns2max.dts | 49 slow-gpio = <&gpio0 29 0>;
|
| A D | kirkwood-ns2mini.dts | 50 slow-gpio = <&gpio0 29 0>;
|
| /u-boot/test/py/ |
| A D | pytest.ini | 13 slow: U-Boot: Specific test will run slowly.
|
| /u-boot/board/freescale/t208xqds/ |
| A D | t208x_pbi.cfg | 25 #Initialize eSPI controller, default configuration is slow for eSPI to
|
| /u-boot/board/freescale/t208xrdb/ |
| A D | t2080_pbi.cfg | 25 #Initialize eSPI controller, default configuration is slow for eSPI to
|
| /u-boot/doc/ |
| A D | README.commands.itest | 1 A slow day today so here is a revised itest command with provisional
|
| A D | README.iomux | 74 On a slow machine, such as MPC852T clocked at 66MHz, the overhead associated
81 is quite slow. Even on a sequoia cut&paste does not work on the serial
|
| /u-boot/test/py/tests/test_efi_secboot/ |
| A D | test_signed_intca.py | 21 @pytest.mark.slow
|
| A D | test_unsigned.py | 19 @pytest.mark.slow
|
| A D | test_signed.py | 19 @pytest.mark.slow
|
| A D | test_authvar.py | 18 @pytest.mark.slow
|
| /u-boot/board/keymile/kmp204x/ |
| A D | pbi.cfg | 65 #Initialize eSPI controller, default configuration is slow for eSPI to
|
| /u-boot/test/py/tests/test_fs/ |
| A D | test_unlink.py | 16 @pytest.mark.slow
|
| A D | test_mkdir.py | 15 @pytest.mark.slow
|
| A D | test_symlink.py | 19 @pytest.mark.slow
|
| /u-boot/arch/x86/cpu/ivybridge/ |
| A D | Kconfig | 55 emulation (which would be very slow).
|
| /u-boot/test/py/tests/test_efi_capsule/ |
| A D | test_capsule_firmware.py | 27 @pytest.mark.slow
|
| /u-boot/arch/arm/mach-rockchip/rk3368/ |
| A D | Kconfig | 22 - various 'slow' interfaces (e.g. UART, SPI, I2C, I2S, ...)
|
| /u-boot/board/qualcomm/dragonboard410c/ |
| A D | readme.txt | 42 - SDHCI is slow (~2.5MiB/s for SD and eMMC)
|
| /u-boot/board/freescale/mx6memcal/ |
| A D | README | 15 makes running the DDR very slow or a working U-Boot image that
|
Completed in 35 milliseconds
123