Home
last modified time | relevance | path

Searched refs:standard (Results 1 – 25 of 108) sorted by relevance

12345

/u-boot/arch/arm/dts/
A Dzynq-zc702.dts210 io-standard = <1>;
233 io-standard = <4>;
256 io-standard = <1>;
274 io-standard = <1>;
298 io-standard = <1>;
311 io-standard = <1>;
324 io-standard = <1>;
338 io-standard = <1>;
351 io-standard = <1>;
364 io-standard = <1>;
[all …]
A Dzynq-zc706.dts154 io-standard = <4>;
177 io-standard = <1>;
191 io-standard = <1>;
215 io-standard = <1>;
228 io-standard = <1>;
242 io-standard = <1>;
255 io-standard = <1>;
268 io-standard = <1>;
291 io-standard = <1>;
/u-boot/drivers/tpm/
A DKconfig33 to the device using the standard TPM Interface Specification (TIS)
42 to the device using the standard TPM Interface Specification (TIS)
66 to the device using the standard TPM Interface Specification (TIS)
84 to the device using the standard TPM Interface Specification (TIS)
93 to the device using the standard TPM Interface Specification (TIS)
155 to the device using the standard TPM Interface Specification (TIS)
/u-boot/doc/device-tree-bindings/reserved-memory/
A Dreserved-memory.txt14 #address-cells, #size-cells (required) - standard definition
16 ranges (required) - standard definition
34 reg (required) - standard definition
48 compatible (optional) - standard definition
57 of the region as part of its standard mapping of system memory,
/u-boot/drivers/usb/cdns3/
A DKconfig29 standard XHCI driver.
50 standard XHCI driver.
/u-boot/doc/device-tree-bindings/exynos/
A Dsoc.txt3 The "cpu-model" property is a non-standard extension for the device tree root
/u-boot/doc/
A DREADME.vxworks28 Since VxWorks 7 SR0640 release, VxWorks starts using Linux compatible standard
31 only when the least significant bit of flags in bootargs is set, the standard
38 the ePAPR standard, which is shown below (see ePAPR for more details):
46 When using the Linux compatible standard DTB, the calling convention of VxWorks
A DREADME.asn14 Abstract Syntax Notation One (or ASN1) is a standard by ITU-T and ISO/IEC
A DREADME.bootcount12 "bootlimit", then instead of the standard boot action (executing the contents of
/u-boot/drivers/firmware/scmi/
A DKconfig8 protocol that defines standard interfaces for power, performance
/u-boot/doc/device-tree-bindings/usb/
A Dmarvell.xhci-usb.txt10 - reg: should contain address and length of the standard XHCI
/u-boot/doc/device-tree-bindings/regulator/
A Dtps65090.txt10 standard binding for regulators; see regulator.txt.
25 Each regulator is defined using the standard binding for regulators.
/u-boot/drivers/usb/host/
A DKconfig13 The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0
112 The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
236 The Open Host Controller Interface (OHCI) is a standard for accessing
274 The Universal Host Controller Interface is a standard by Intel for
277 standard, you may want to say Y, but see below. All recent boards
279 i810, i820) conform to this standard. Also all VIA PCI chipsets
/u-boot/doc/device-tree-bindings/rtc/
A Dabracon,abx80x.txt29 - "abracon,tc-diode": should be "standard" (0.6V) or "schottky" (0.3V)
/u-boot/board/toradex/apalis_imx6/
A DKconfig47 thus unusable on standard carrier boards.
/u-boot/doc/board/emulation/
A Dqemu-ppce500.rst11 support for the VirtIO standard networking device connected to the built-in
67 By default a VirtIO standard PCI networking device is connected as an ethernet
/u-boot/board/ste/stemmy/
A DREADME46 UART is available through the micro USB port, similar to the Carkit standard.
/u-boot/doc/device-tree-bindings/pci/
A Darmada8k-pcie.txt11 - interrupt-map-mask and interrupt-map, standard PCI properties to
A Dmediatek-pcie.txt29 Please refer to the standard PCI bus binding document for a more detailed
46 Please refer to the standard PCI bus binding document for a more detailed
/u-boot/disk/
A DKconfig93 meant to allow less than the standard specifies for devices
97 If unsure, leave at 128 entries, which is the standard
/u-boot/board/armltd/integrator/
A DREADME32 U-Boot has to carry out minimal configration before standard code is run.
55 Otherwise. for example, the standard CM reset via the CM control register would
/u-boot/drivers/ata/
A DKconfig6 types can use this, such as AHCI/SATA. It does not provide any standard
15 Attachment), a serial bus standard for connecting to hard drives and
/u-boot/board/freescale/ls1043ardb/
A DREADME18 standard PCIe card
/u-boot/doc/device-tree-bindings/clock/
A Drockchip,rk3288-cru.txt29 that they are defined using standard clock bindings with following
/u-boot/doc/usage/
A Dnetconsole.rst4 In U-Boot, we implemented the networked console via the standard
48 standard output. It will be built when compiling for a board which

Completed in 28 milliseconds

12345