Searched refs:INT1 (Results 1 – 25 of 27) sorted by relevance
12
| /linux/arch/mips/pci/ |
| A D | fixup-capcella.c | 15 #define INT1 RTL8139_1_IRQ macro
23 [11] = { -1, INT1, INT1, INT1, INT1 },
|
| /linux/Documentation/devicetree/bindings/iio/accel/ |
| A D | fsl,mma7455.yaml | 33 Data ready is only available on INT1, but events can use either or
35 to INT1 and second (where present) to INT2.
40 - "INT1"
64 interrupt-names = "INT2", "INT1";
79 interrupt-names = "INT1";
|
| A D | bosch,bma255.yaml | 50 connected to the INT1 pin, the second (optional) interrupt listed must be
54 BMC156 does not have an INT1 pin, therefore the first interrupt pin is
62 - INT1
89 interrupt-names = "INT1";
|
| A D | nxp,fxls8962af.yaml | 37 - INT1
62 interrupt-names = "INT1";
78 interrupt-names = "INT1";
|
| A D | adi,adxl313.yaml | 44 - INT1
67 interrupt-names = "INT1";
84 interrupt-names = "INT1";
|
| A D | fsl,mma8452.yaml | 37 - INT1
|
| A D | bosch,bmi088.yaml | 42 - INT1
|
| A D | adi,adxl355.yaml | 36 - INT1
|
| /linux/Documentation/devicetree/bindings/iio/imu/ |
| A D | bosch,bmi160.yaml | 29 - INT1
32 set to "INT1" if INT1 pin should be used as interrupt input, set
72 interrupt-names = "INT1";
|
| A D | nxp,fxos8700.yaml | 33 - INT1
61 interrupt-names = "INT1";
|
| A D | st,lsm6dsx.yaml | 42 Supports up to 2 interrupt lines via the INT1 and INT2 pins.
|
| /linux/Documentation/devicetree/bindings/iio/gyroscope/ |
| A D | nxp,fxas21002c.yaml | 43 - INT1
78 interrupt-names = "INT1";
|
| /linux/Documentation/devicetree/bindings/iio/magnetometer/ |
| A D | asahi-kasei,ak8974.yaml | 25 Data ready (DRDY) and interrupt (INT1) lines from the chip. The DRDY
|
| /linux/drivers/pinctrl/ |
| A D | pinctrl-pic32.c | 318 FUNCTION(INT1, input3),
491 PIC32_PINCTRL_FUNCTION(INT1, INT1R, 7),
566 PIC32_PINCTRL_FUNCTION(INT1, INT1R, 4),
698 PIC32_PINCTRL_FUNCTION(INT1, INT1R, 2),
776 PIC32_PINCTRL_FUNCTION(INT1, INT1R, 12),
902 PIC32_PINCTRL_FUNCTION(INT1, INT1R, 3),
1004 PIC32_PINCTRL_FUNCTION(INT1, INT1R, 6),
1261 PIC32_PINCTRL_FUNCTION(INT1, INT1R, 13),
1387 PIC32_PINCTRL_FUNCTION(INT1, INT1R, 8),
1516 PIC32_PINCTRL_FUNCTION(INT1, INT1R, 9),
[all …]
|
| /linux/arch/arm64/boot/dts/freescale/ |
| A D | fsl-ls1012a-rdb.dts | 49 interrupt-names = "INT1";
|
| A D | imx8mm-venice-gw71xx.dtsi | 78 interrupt-names = "INT1";
|
| A D | imx8mm-venice-gw72xx.dtsi | 97 interrupt-names = "INT1";
|
| A D | imx8mm-venice-gw73xx.dtsi | 117 interrupt-names = "INT1";
|
| A D | imx8mn-venice-gw7902.dts | 529 interrupt-names = "INT1";
|
| /linux/Documentation/devicetree/bindings/net/can/ |
| A D | microchip,mcp251xfd.yaml | 41 GPIO phandle of GPIO connected to to INT1 pin of the MCP251XFD, which
|
| /linux/arch/arm/boot/dts/ |
| A D | ste-snowball.dts | 336 interrupts = <3 IRQ_TYPE_EDGE_RISING>, /* INT1 */
361 <9 IRQ_TYPE_EDGE_RISING>; /* INT1 */
|
| A D | imx6qdl-gw5912.dtsi | 312 interrupt-names = "INT1";
|
| A D | imx6qdl-gw5910.dtsi | 329 interrupt-names = "INT1";
|
| A D | omap3-n950-n9.dtsi | 62 OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT | MUX_MODE4) /* mcspi2_somi.gpio_180 -> LIS302 INT1 */
|
| /linux/Documentation/devicetree/bindings/iio/ |
| A D | st,st-sensors.yaml | 92 Intertial interrupt lines INT1 and INT2 if these exist. This means up to
|
Completed in 31 milliseconds
12