Searched refs:oversampling (Results 1 – 12 of 12) sorted by relevance
| /linux/Documentation/devicetree/bindings/iio/adc/ |
| A D | ti,tsc2046.yaml | 55 oversampling-ratio: true
87 oversampling-ratio = <5>;
95 oversampling-ratio = <5>;
100 oversampling-ratio = <5>;
105 oversampling-ratio = <5>;
|
| A D | adi,ad7606.yaml | 84 adi,oversampling-ratio-gpios:
94 It is enabled when all three oversampling mode pins are connected to
96 adi,oversampling-ratio-gpios property is defined, then the driver will set the
97 oversampling gpios to high. Otherwise, it is assumed that the pins are hardwired
134 adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH>,
|
| A D | adc.yaml | 46 oversampling-ratio:
|
| /linux/Documentation/devicetree/bindings/media/i2c/ |
| A D | adv7343.txt | 16 - adi,power-mode-pll-ctrl: PLL and oversampling control. This control allows
18 oversampling to be switched off.
|
| /linux/drivers/spi/ |
| A D | spi-geni-qcom.c | 94 unsigned int oversampling; member
114 speed_hz * mas->oversampling, in get_spi_clk_cfg()
122 *clk_div = DIV_ROUND_UP(sclk_freq, mas->oversampling * speed_hz); in get_spi_clk_cfg()
123 actual_hz = sclk_freq / (mas->oversampling * *clk_div); in get_spi_clk_cfg()
561 mas->oversampling = 2; in spi_geni_init()
563 mas->oversampling = 1; in spi_geni_init()
|
| /linux/drivers/iio/adc/ |
| A D | ad7606.c | 194 *val = st->oversampling; in ad7606_read_raw()
288 st->oversampling = st->oversampling_avail[i]; in ad7606_write_raw()
587 st->oversampling = 1; in ad7606_probe()
|
| A D | ad7606.h | 98 unsigned int oversampling; member
|
| /linux/drivers/tty/serial/ |
| A D | amba-pl011.c | 84 bool oversampling; member
105 .oversampling = false,
120 .oversampling = false,
136 .oversampling = false,
183 .oversampling = true,
2035 if (uap->vendor->oversampling) in pl011_set_termios()
2123 if (uap->vendor->oversampling) { in pl011_set_termios()
2136 if (uap->vendor->oversampling) { in pl011_set_termios()
2408 if (uap->vendor->oversampling) { in pl011_console_get_options()
|
| A D | stm32-usart.c | 926 u32 usartdiv, mantissa, fraction, oversampling; in stm32_usart_set_termios() local
1037 oversampling = 8; in stm32_usart_set_termios()
1041 oversampling = 16; in stm32_usart_set_termios()
1046 mantissa = (usartdiv / oversampling) << USART_BRR_DIV_M_SHIFT; in stm32_usart_set_termios()
1047 fraction = usartdiv % oversampling; in stm32_usart_set_termios()
|
| /linux/Documentation/sound/soc/ |
| A D | overview.rst | 24 power via changing codec oversampling rates, bias currents, etc.
|
| /linux/drivers/tty/serial/8250/ |
| A D | Kconfig | 354 Uses 8 times oversampling (compared to 16 times for 16650)
|
| /linux/Documentation/ABI/testing/ |
| A D | sysfs-bus-iio | 124 Hardware dependent ADC oversampling. Controls the sampling ratio
131 Hardware dependent values supported by the oversampling filter.
|
Completed in 31 milliseconds