1# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/interrupt-controller/ti,sci-intr.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: Texas Instruments K3 Interrupt Router
8
9maintainers:
10  - Lokesh Vutla <lokeshvutla@ti.com>
11
12allOf:
13  - $ref: /schemas/arm/keystone/ti,k3-sci-common.yaml#
14
15description: |
16  The Interrupt Router (INTR) module provides a mechanism to mux M
17  interrupt inputs to N interrupt outputs, where all M inputs are selectable
18  to be driven per N output. An Interrupt Router can either handle edge
19  triggered or level triggered interrupts and that is fixed in hardware.
20
21                                   Interrupt Router
22                               +----------------------+
23                               |  Inputs     Outputs  |
24          +-------+            | +------+    +-----+  |
25          | GPIO  |----------->| | irq0 |    |  0  |  |       Host IRQ
26          +-------+            | +------+    +-----+  |      controller
27                               |    .           .     |      +-------+
28          +-------+            |    .           .     |----->|  IRQ  |
29          | INTA  |----------->|    .           .     |      +-------+
30          +-------+            |    .        +-----+  |
31                               | +------+    |  N  |  |
32                               | | irqM |    +-----+  |
33                               | +------+             |
34                               |                      |
35                               +----------------------+
36
37  There is one register per output (MUXCNTL_N) that controls the selection.
38  Configuration of these MUXCNTL_N registers is done by a system controller
39  (like the Device Memory and Security Controller on K3 AM654 SoC). System
40  controller will keep track of the used and unused registers within the Router.
41  Driver should request the system controller to get the range of GIC IRQs
42  assigned to the requesting hosts. It is the drivers responsibility to keep
43  track of Host IRQs.
44
45  Communication between the host processor running an OS and the system
46  controller happens through a protocol called TI System Control Interface
47  (TISCI protocol).
48
49properties:
50  compatible:
51    const: ti,sci-intr
52
53  ti,intr-trigger-type:
54    $ref: /schemas/types.yaml#/definitions/uint32
55    enum: [1, 4]
56    description: |
57      Should be one of the following.
58        1 = If intr supports edge triggered interrupts.
59        4 = If intr supports level triggered interrupts.
60
61  interrupt-controller: true
62
63  '#interrupt-cells':
64    const: 1
65    description: |
66      The 1st cell should contain interrupt router input hw number.
67
68  ti,interrupt-ranges:
69    $ref: /schemas/types.yaml#/definitions/uint32-matrix
70    description: |
71      Interrupt ranges that converts the INTR output hw irq numbers
72      to parents's input interrupt numbers.
73    items:
74      items:
75        - description: |
76            "output_irq" specifies the base for intr output irq
77        - description: |
78            "parent's input irq" specifies the base for parent irq
79        - description: |
80            "limit" specifies the limit for translation
81
82required:
83  - compatible
84  - ti,intr-trigger-type
85  - interrupt-controller
86  - '#interrupt-cells'
87  - ti,sci
88  - ti,sci-dev-id
89  - ti,interrupt-ranges
90
91unevaluatedProperties: false
92
93examples:
94  - |
95    main_gpio_intr: interrupt-controller0 {
96        compatible = "ti,sci-intr";
97        ti,intr-trigger-type = <1>;
98        interrupt-controller;
99        interrupt-parent = <&gic500>;
100        #interrupt-cells = <1>;
101        ti,sci = <&dmsc>;
102        ti,sci-dev-id = <131>;
103        ti,interrupt-ranges = <0 360 32>;
104    };
105