1// SPDX-License-Identifier: GPL-2.0+
2/*
3 * Copyright (C) 2015 Altera Corporation <www.altera.com>
4 */
5#include "socfpga_arria10.dtsi"
6
7/ {
8	model = "Altera SOCFPGA Arria 10";
9	compatible = "altr,socfpga-arria10", "altr,socfpga";
10
11	aliases {
12		ethernet0 = &gmac0;
13		serial0 = &uart1;
14	};
15
16	chosen {
17		bootargs = "earlyprintk";
18		stdout-path = "serial0:115200n8";
19	};
20
21	memory@0 {
22		name = "memory";
23		device_type = "memory";
24		reg = <0x0 0x40000000>; /* 1GB */
25	};
26
27	a10leds {
28		compatible = "gpio-leds";
29
30		a10sr_led0 {
31			label = "a10sr-led0";
32			gpios = <&a10sr_gpio 0 1>;
33		};
34
35		a10sr_led1 {
36			label = "a10sr-led1";
37			gpios = <&a10sr_gpio 1 1>;
38		};
39
40		a10sr_led2 {
41			label = "a10sr-led2";
42			gpios = <&a10sr_gpio 2 1>;
43		};
44
45		a10sr_led3 {
46			label = "a10sr-led3";
47			gpios = <&a10sr_gpio 3 1>;
48		};
49	};
50
51	ref_033v: 033-v-ref {
52		compatible = "regulator-fixed";
53		regulator-name = "0.33V";
54		regulator-min-microvolt = <330000>;
55		regulator-max-microvolt = <330000>;
56	};
57
58	soc {
59		clkmgr@ffd04000 {
60			clocks {
61				osc1 {
62					clock-frequency = <25000000>;
63				};
64			};
65		};
66	};
67};
68
69&gmac0 {
70	phy-mode = "rgmii";
71	phy-addr = <0xffffffff>; /* probe for phy addr */
72
73	/*
74	 * These skews assume the user's FPGA design is adding 600ps of delay
75	 * for TX_CLK on Arria 10.
76	 *
77	 * All skews are offset since hardware skew values for the ksz9031
78	 * range from a negative skew to a positive skew.
79	 * See the micrel-ksz90x1.txt Documentation file for details.
80	 */
81	txd0-skew-ps = <0>; /* -420ps */
82	txd1-skew-ps = <0>; /* -420ps */
83	txd2-skew-ps = <0>; /* -420ps */
84	txd3-skew-ps = <0>; /* -420ps */
85	rxd0-skew-ps = <420>; /* 0ps */
86	rxd1-skew-ps = <420>; /* 0ps */
87	rxd2-skew-ps = <420>; /* 0ps */
88	rxd3-skew-ps = <420>; /* 0ps */
89	txen-skew-ps = <0>; /* -420ps */
90	txc-skew-ps = <1860>; /* 960ps */
91	rxdv-skew-ps = <420>; /* 0ps */
92	rxc-skew-ps = <1680>; /* 780ps */
93	max-frame-size = <3800>;
94	status = "okay";
95};
96
97&gpio1 {
98	status = "okay";
99};
100
101&spi1 {
102	status = "okay";
103
104	resource-manager@0 {
105		compatible = "altr,a10sr";
106		reg = <0>;
107		spi-max-frequency = <100000>;
108		/* low-level active IRQ at GPIO1_5 */
109		interrupt-parent = <&portb>;
110		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
111		interrupt-controller;
112		#interrupt-cells = <2>;
113
114		a10sr_gpio: gpio-controller {
115			compatible = "altr,a10sr-gpio";
116			gpio-controller;
117			#gpio-cells = <2>;
118		};
119
120		a10sr_rst: reset-controller {
121			compatible = "altr,a10sr-reset";
122			#reset-cells = <1>;
123		};
124	};
125};
126
127&i2c1 {
128	status = "okay";
129
130	/*
131	 * adjust the falling times to decrease the i2c frequency to 50Khz
132	 * because the LCD module does not work at the standard 100Khz
133	 */
134	clock-frequency = <100000>;
135	i2c-sda-falling-time-ns = <6000>;
136	i2c-scl-falling-time-ns = <6000>;
137
138	adc@14 {
139		compatible = "lltc,ltc2497";
140		reg = <0x14>;
141		vref-supply = <&ref_033v>;
142	};
143
144	adc@16 {
145		compatible = "lltc,ltc2497";
146		reg = <0x16>;
147		vref-supply = <&ref_033v>;
148	};
149
150	eeprom@51 {
151		compatible = "atmel,24c32";
152		reg = <0x51>;
153		pagesize = <32>;
154	};
155
156	rtc@68 {
157		compatible = "dallas,ds1339";
158		reg = <0x68>;
159	};
160
161	ltc@5c {
162		compatible = "ltc2977";
163		reg = <0x5c>;
164	};
165
166	temp@4c {
167		compatible = "maxim,max1619";
168		reg = <0x4c>;
169	};
170};
171
172&uart1 {
173	status = "okay";
174};
175
176&usb0 {
177	status = "okay";
178	disable-over-current;
179};
180
181&watchdog1 {
182	status = "okay";
183};
184