1 /*
2 * arch/arm/mach-lpc32xx/pm.c
3 *
4 * Original authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com>
5 * Modified by Kevin Wells <kevin.wells@nxp.com>
6 *
7 * 2005 (c) MontaVista Software, Inc. This file is licensed under
8 * the terms of the GNU General Public License version 2. This program
9 * is licensed "as is" without any warranty of any kind, whether express
10 * or implied.
11 */
12
13 /*
14 * LPC32XX CPU and system power management
15 *
16 * The LPC32XX has three CPU modes for controlling system power: run,
17 * direct-run, and halt modes. When switching between halt and run modes,
18 * the CPU transistions through direct-run mode. For Linux, direct-run
19 * mode is not used in normal operation. Halt mode is used when the
20 * system is fully suspended.
21 *
22 * Run mode:
23 * The ARM CPU clock (HCLK_PLL), HCLK bus clock, and PCLK bus clocks are
24 * derived from the HCLK PLL. The HCLK and PCLK bus rates are divided from
25 * the HCLK_PLL rate. Linux runs in this mode.
26 *
27 * Direct-run mode:
28 * The ARM CPU clock, HCLK bus clock, and PCLK bus clocks are driven from
29 * SYSCLK. SYSCLK is usually around 13MHz, but may vary based on SYSCLK
30 * source or the frequency of the main oscillator. In this mode, the
31 * HCLK_PLL can be safely enabled, changed, or disabled.
32 *
33 * Halt mode:
34 * SYSCLK is gated off and the CPU and system clocks are halted.
35 * Peripherals based on the 32KHz oscillator clock (ie, RTC, touch,
36 * key scanner, etc.) still operate if enabled. In this state, an enabled
37 * system event (ie, GPIO state change, RTC match, key press, etc.) will
38 * wake the system up back into direct-run mode.
39 *
40 * DRAM refresh
41 * DRAM clocking and refresh are slightly different for systems with DDR
42 * DRAM or regular SDRAM devices. If SDRAM is used in the system, the
43 * SDRAM will still be accessible in direct-run mode. In DDR based systems,
44 * a transition to direct-run mode will stop all DDR accesses (no clocks).
45 * Because of this, the code to switch power modes and the code to enter
46 * and exit DRAM self-refresh modes must not be executed in DRAM. A small
47 * section of IRAM is used instead for this.
48 *
49 * Suspend is handled with the following logic:
50 * Backup a small area of IRAM used for the suspend code
51 * Copy suspend code to IRAM
52 * Transfer control to code in IRAM
53 * Places DRAMs in self-refresh mode
54 * Enter direct-run mode
55 * Save state of HCLK_PLL PLL
56 * Disable HCLK_PLL PLL
57 * Enter halt mode - CPU and buses will stop
58 * System enters direct-run mode when an enabled event occurs
59 * HCLK PLL state is restored
60 * Run mode is entered
61 * DRAMS are placed back into normal mode
62 * Code execution returns from IRAM
63 * IRAM code are used for suspend is restored
64 * Suspend mode is exited
65 */
66
67 #include <linux/suspend.h>
68 #include <linux/io.h>
69 #include <linux/slab.h>
70
71 #include <asm/cacheflush.h>
72
73 #include "lpc32xx.h"
74 #include "common.h"
75
76 #define TEMP_IRAM_AREA IO_ADDRESS(LPC32XX_IRAM_BASE)
77
78 /*
79 * Both STANDBY and MEM suspend states are handled the same with no
80 * loss of CPU or memory state
81 */
lpc32xx_pm_enter(suspend_state_t state)82 static int lpc32xx_pm_enter(suspend_state_t state)
83 {
84 int (*lpc32xx_suspend_ptr) (void);
85 void *iram_swap_area;
86
87 /* Allocate some space for temporary IRAM storage */
88 iram_swap_area = kmemdup((void *)TEMP_IRAM_AREA,
89 lpc32xx_sys_suspend_sz, GFP_KERNEL);
90 if (!iram_swap_area)
91 return -ENOMEM;
92
93 /*
94 * Copy code to suspend system into IRAM. The suspend code
95 * needs to run from IRAM as DRAM may no longer be available
96 * when the PLL is stopped.
97 */
98 memcpy((void *) TEMP_IRAM_AREA, &lpc32xx_sys_suspend,
99 lpc32xx_sys_suspend_sz);
100 flush_icache_range((unsigned long)TEMP_IRAM_AREA,
101 (unsigned long)(TEMP_IRAM_AREA) + lpc32xx_sys_suspend_sz);
102
103 /* Transfer to suspend code in IRAM */
104 lpc32xx_suspend_ptr = (void *) TEMP_IRAM_AREA;
105 flush_cache_all();
106 (void) lpc32xx_suspend_ptr();
107
108 /* Restore original IRAM contents */
109 memcpy((void *) TEMP_IRAM_AREA, iram_swap_area,
110 lpc32xx_sys_suspend_sz);
111
112 kfree(iram_swap_area);
113
114 return 0;
115 }
116
117 static const struct platform_suspend_ops lpc32xx_pm_ops = {
118 .valid = suspend_valid_only_mem,
119 .enter = lpc32xx_pm_enter,
120 };
121
122 #define EMC_DYN_MEM_CTRL_OFS 0x20
123 #define EMC_SRMMC (1 << 3)
124 #define EMC_CTRL_REG io_p2v(LPC32XX_EMC_BASE + EMC_DYN_MEM_CTRL_OFS)
lpc32xx_pm_init(void)125 static int __init lpc32xx_pm_init(void)
126 {
127 /*
128 * Setup SDRAM self-refresh clock to automatically disable o
129 * start of self-refresh. This only needs to be done once.
130 */
131 __raw_writel(__raw_readl(EMC_CTRL_REG) | EMC_SRMMC, EMC_CTRL_REG);
132
133 suspend_set_ops(&lpc32xx_pm_ops);
134
135 return 0;
136 }
137 arch_initcall(lpc32xx_pm_init);
138