1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3  * Driver for Silicon Labs C8051F300 microcontroller.
4  *
5  * It is used for LNB power control in TeVii S470,
6  * TBS 6920 PCIe DVB-S2 cards.
7  *
8  * Microcontroller connected to cx23885 GPIO pins:
9  * GPIO0 - data		- P0.3 F300
10  * GPIO1 - reset	- P0.2 F300
11  * GPIO2 - clk		- P0.1 F300
12  * GPIO3 - busy		- P0.0 F300
13  *
14  * Copyright (C) 2009 Igor M. Liplianin <liplianin@me.by>
15  */
16 
17 #include "cx23885.h"
18 #include "cx23885-f300.h"
19 
20 #define F300_DATA	GPIO_0
21 #define F300_RESET	GPIO_1
22 #define F300_CLK	GPIO_2
23 #define F300_BUSY	GPIO_3
24 
f300_set_line(struct cx23885_dev * dev,u32 line,u8 lvl)25 static void f300_set_line(struct cx23885_dev *dev, u32 line, u8 lvl)
26 {
27 	cx23885_gpio_enable(dev, line, 1);
28 	if (lvl == 1)
29 		cx23885_gpio_set(dev, line);
30 	else
31 		cx23885_gpio_clear(dev, line);
32 }
33 
f300_get_line(struct cx23885_dev * dev,u32 line)34 static u8 f300_get_line(struct cx23885_dev *dev, u32 line)
35 {
36 	cx23885_gpio_enable(dev, line, 0);
37 
38 	return cx23885_gpio_get(dev, line);
39 }
40 
f300_send_byte(struct cx23885_dev * dev,u8 dta)41 static void f300_send_byte(struct cx23885_dev *dev, u8 dta)
42 {
43 	u8 i;
44 
45 	for (i = 0; i < 8; i++) {
46 		f300_set_line(dev, F300_CLK, 0);
47 		udelay(30);
48 		f300_set_line(dev, F300_DATA, (dta & 0x80) >> 7);/* msb first */
49 		udelay(30);
50 		dta <<= 1;
51 		f300_set_line(dev, F300_CLK, 1);
52 		udelay(30);
53 	}
54 }
55 
f300_get_byte(struct cx23885_dev * dev)56 static u8 f300_get_byte(struct cx23885_dev *dev)
57 {
58 	u8 i, dta = 0;
59 
60 	for (i = 0; i < 8; i++) {
61 		f300_set_line(dev, F300_CLK, 0);
62 		udelay(30);
63 		dta <<= 1;
64 		f300_set_line(dev, F300_CLK, 1);
65 		udelay(30);
66 		dta |= f300_get_line(dev, F300_DATA);/* msb first */
67 
68 	}
69 
70 	return dta;
71 }
72 
f300_xfer(struct dvb_frontend * fe,u8 * buf)73 static u8 f300_xfer(struct dvb_frontend *fe, u8 *buf)
74 {
75 	struct cx23885_tsport *port = fe->dvb->priv;
76 	struct cx23885_dev *dev = port->dev;
77 	u8 i, temp, ret = 0;
78 
79 	temp = buf[0];
80 	for (i = 0; i < buf[0]; i++)
81 		temp += buf[i + 1];
82 	temp = (~temp + 1);/* get check sum */
83 	buf[1 + buf[0]] = temp;
84 
85 	f300_set_line(dev, F300_RESET, 1);
86 	f300_set_line(dev, F300_CLK, 1);
87 	udelay(30);
88 	f300_set_line(dev, F300_DATA, 1);
89 	msleep(1);
90 
91 	/* question: */
92 	f300_set_line(dev, F300_RESET, 0);/* begin to send data */
93 	msleep(1);
94 
95 	f300_send_byte(dev, 0xe0);/* the slave address is 0xe0, write */
96 	msleep(1);
97 
98 	temp = buf[0];
99 	temp += 2;
100 	for (i = 0; i < temp; i++)
101 		f300_send_byte(dev, buf[i]);
102 
103 	f300_set_line(dev, F300_RESET, 1);/* sent data over */
104 	f300_set_line(dev, F300_DATA, 1);
105 
106 	/* answer: */
107 	temp = 0;
108 	for (i = 0; ((i < 8) & (temp == 0)); i++) {
109 		msleep(1);
110 		if (f300_get_line(dev, F300_BUSY) == 0)
111 			temp = 1;
112 	}
113 
114 	if (i > 7) {
115 		pr_err("%s: timeout, the slave no response\n",
116 								__func__);
117 		ret = 1; /* timeout, the slave no response */
118 	} else { /* the slave not busy, prepare for getting data */
119 		f300_set_line(dev, F300_RESET, 0);/*ready...*/
120 		msleep(1);
121 		f300_send_byte(dev, 0xe1);/* 0xe1 is Read */
122 		msleep(1);
123 		temp = f300_get_byte(dev);/*get the data length */
124 		if (temp > 14)
125 			temp = 14;
126 
127 		for (i = 0; i < (temp + 1); i++)
128 			f300_get_byte(dev);/* get data to empty buffer */
129 
130 		f300_set_line(dev, F300_RESET, 1);/* received data over */
131 		f300_set_line(dev, F300_DATA, 1);
132 	}
133 
134 	return ret;
135 }
136 
f300_set_voltage(struct dvb_frontend * fe,enum fe_sec_voltage voltage)137 int f300_set_voltage(struct dvb_frontend *fe, enum fe_sec_voltage voltage)
138 {
139 	u8 buf[16];
140 
141 	buf[0] = 0x05;
142 	buf[1] = 0x38;/* write port */
143 	buf[2] = 0x01;/* A port, lnb power */
144 
145 	switch (voltage) {
146 	case SEC_VOLTAGE_13:
147 		buf[3] = 0x01;/* power on */
148 		buf[4] = 0x02;/* B port, H/V */
149 		buf[5] = 0x00;/*13V v*/
150 		break;
151 	case SEC_VOLTAGE_18:
152 		buf[3] = 0x01;
153 		buf[4] = 0x02;
154 		buf[5] = 0x01;/* 18V h*/
155 		break;
156 	case SEC_VOLTAGE_OFF:
157 		buf[3] = 0x00;/* power off */
158 		buf[4] = 0x00;
159 		buf[5] = 0x00;
160 		break;
161 	}
162 
163 	return f300_xfer(fe, buf);
164 }
165