1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Device Tree Source for the Lager board
4 *
5 * Copyright (C) 2013-2014 Renesas Solutions Corp.
6 * Copyright (C) 2014 Cogent Embedded, Inc.
7 * Copyright (C) 2015-2016 Renesas Electronics Corporation
8 */
9
10/*
11 * SSI-AK4643
12 *
13 * SW1: 1: AK4643
14 *      2: CN22
15 *      3: ADV7511
16 *
17 * This command is required when Playback/Capture
18 *
19 *	amixer set "LINEOUT Mixer DACL" on
20 *	amixer set "DVC Out" 100%
21 *	amixer set "DVC In" 100%
22 *
23 * You can use Mute
24 *
25 *	amixer set "DVC Out Mute" on
26 *	amixer set "DVC In Mute" on
27 *
28 * You can use Volume Ramp
29 *
30 *	amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
31 *	amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
32 *	amixer set "DVC Out Ramp" on
33 *	aplay xxx.wav &
34 *	amixer set "DVC Out"  80%  // Volume Down
35 *	amixer set "DVC Out" 100%  // Volume Up
36 */
37
38/dts-v1/;
39#include "r8a7790.dtsi"
40#include <dt-bindings/gpio/gpio.h>
41#include <dt-bindings/input/input.h>
42
43/ {
44	model = "Lager";
45	compatible = "renesas,lager", "renesas,r8a7790";
46
47	aliases {
48		serial0 = &scif0;
49		serial1 = &scifa1;
50		i2c8 = &gpioi2c1;
51		i2c9 = &gpioi2c2;
52		i2c10 = &i2cexio0;
53		i2c11 = &i2cexio1;
54		i2c12 = &i2chdmi;
55		i2c13 = &i2cpwr;
56	};
57
58	chosen {
59		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
60		stdout-path = "serial0:115200n8";
61	};
62
63	memory@40000000 {
64		device_type = "memory";
65		reg = <0 0x40000000 0 0x40000000>;
66	};
67
68	memory@140000000 {
69		device_type = "memory";
70		reg = <1 0x40000000 0 0xc0000000>;
71	};
72
73	lbsc {
74		#address-cells = <1>;
75		#size-cells = <1>;
76	};
77
78	keyboard {
79		compatible = "gpio-keys";
80
81		one {
82			linux,code = <KEY_1>;
83			label = "SW2-1";
84			wakeup-source;
85			debounce-interval = <20>;
86			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
87		};
88		two {
89			linux,code = <KEY_2>;
90			label = "SW2-2";
91			wakeup-source;
92			debounce-interval = <20>;
93			gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
94		};
95		three {
96			linux,code = <KEY_3>;
97			label = "SW2-3";
98			wakeup-source;
99			debounce-interval = <20>;
100			gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
101		};
102		four {
103			linux,code = <KEY_4>;
104			label = "SW2-4";
105			wakeup-source;
106			debounce-interval = <20>;
107			gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
108		};
109	};
110
111	leds {
112		compatible = "gpio-leds";
113		led6 {
114			gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
115		};
116		led7 {
117			gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
118		};
119		led8 {
120			gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
121		};
122	};
123
124	fixedregulator3v3: regulator-3v3 {
125		compatible = "regulator-fixed";
126		regulator-name = "fixed-3.3V";
127		regulator-min-microvolt = <3300000>;
128		regulator-max-microvolt = <3300000>;
129		regulator-boot-on;
130		regulator-always-on;
131	};
132
133	vcc_sdhi0: regulator-vcc-sdhi0 {
134		compatible = "regulator-fixed";
135
136		regulator-name = "SDHI0 Vcc";
137		regulator-min-microvolt = <3300000>;
138		regulator-max-microvolt = <3300000>;
139
140		gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>;
141		enable-active-high;
142	};
143
144	vccq_sdhi0: regulator-vccq-sdhi0 {
145		compatible = "regulator-gpio";
146
147		regulator-name = "SDHI0 VccQ";
148		regulator-min-microvolt = <1800000>;
149		regulator-max-microvolt = <3300000>;
150
151		gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
152		gpios-states = <1>;
153		states = <3300000 1>, <1800000 0>;
154	};
155
156	vcc_sdhi2: regulator-vcc-sdhi2 {
157		compatible = "regulator-fixed";
158
159		regulator-name = "SDHI2 Vcc";
160		regulator-min-microvolt = <3300000>;
161		regulator-max-microvolt = <3300000>;
162
163		gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>;
164		enable-active-high;
165	};
166
167	vccq_sdhi2: regulator-vccq-sdhi2 {
168		compatible = "regulator-gpio";
169
170		regulator-name = "SDHI2 VccQ";
171		regulator-min-microvolt = <1800000>;
172		regulator-max-microvolt = <3300000>;
173
174		gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>;
175		gpios-states = <1>;
176		states = <3300000 1>, <1800000 0>;
177	};
178
179	audio_clock: audio_clock {
180		compatible = "fixed-clock";
181		#clock-cells = <0>;
182		clock-frequency = <11289600>;
183	};
184
185	rsnd_ak4643: sound {
186		compatible = "simple-audio-card";
187
188		simple-audio-card,format = "left_j";
189		simple-audio-card,bitclock-master = <&sndcodec>;
190		simple-audio-card,frame-master = <&sndcodec>;
191
192		sndcpu: simple-audio-card,cpu {
193			sound-dai = <&rcar_sound>;
194		};
195
196		sndcodec: simple-audio-card,codec {
197			sound-dai = <&ak4643>;
198			clocks = <&audio_clock>;
199		};
200	};
201
202	vga-encoder {
203		compatible = "adi,adv7123";
204
205		ports {
206			#address-cells = <1>;
207			#size-cells = <0>;
208
209			port@0 {
210				reg = <0>;
211				adv7123_in: endpoint {
212					remote-endpoint = <&du_out_rgb>;
213				};
214			};
215			port@1 {
216				reg = <1>;
217				adv7123_out: endpoint {
218					remote-endpoint = <&vga_in>;
219				};
220			};
221		};
222	};
223
224	vga {
225		compatible = "vga-connector";
226
227		port {
228			vga_in: endpoint {
229				remote-endpoint = <&adv7123_out>;
230			};
231		};
232	};
233
234	hdmi-in {
235		compatible = "hdmi-connector";
236		type = "a";
237
238		port {
239			hdmi_con_in: endpoint {
240				remote-endpoint = <&adv7612_in>;
241			};
242		};
243	};
244
245	cec_clock: cec-clock {
246		compatible = "fixed-clock";
247		#clock-cells = <0>;
248		clock-frequency = <12000000>;
249	};
250
251	hdmi-out {
252		compatible = "hdmi-connector";
253		type = "a";
254
255		port {
256			hdmi_con_out: endpoint {
257				remote-endpoint = <&adv7511_out>;
258			};
259		};
260	};
261
262	x2_clk: x2-clock {
263		compatible = "fixed-clock";
264		#clock-cells = <0>;
265		clock-frequency = <148500000>;
266	};
267
268	x13_clk: x13-clock {
269		compatible = "fixed-clock";
270		#clock-cells = <0>;
271		clock-frequency = <148500000>;
272	};
273
274	gpioi2c1: i2c-8 {
275		#address-cells = <1>;
276		#size-cells = <0>;
277		compatible = "i2c-gpio";
278		status = "disabled";
279		scl-gpios = <&gpio1 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
280		sda-gpios = <&gpio1 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
281		i2c-gpio,delay-us = <5>;
282	};
283
284	gpioi2c2: i2c-9 {
285		#address-cells = <1>;
286		#size-cells = <0>;
287		compatible = "i2c-gpio";
288		status = "disabled";
289		scl-gpios = <&gpio5 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
290		sda-gpios = <&gpio5 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
291		i2c-gpio,delay-us = <5>;
292	};
293
294	/*
295	 * IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
296	 * We use the I2C demuxer, so the desired IP core can be selected at runtime
297	 * depending on the use case (e.g. DMA with IIC0 or slave support with I2C0).
298	 * Note: For testing the I2C slave feature, it is convenient to connect this
299	 * bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and
300	 * instantiate the slave device at runtime according to the documentation.
301	 * You can then communicate with the slave via IIC3.
302	 *
303	 * IIC0/I2C0 does not appear to support fallback to GPIO.
304	 */
305	i2cexio0: i2c-10 {
306		compatible = "i2c-demux-pinctrl";
307		i2c-parent = <&iic0>, <&i2c0>;
308		i2c-bus-name = "i2c-exio0";
309		#address-cells = <1>;
310		#size-cells = <0>;
311	};
312
313	/*
314	 * IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA).
315	 * This is similar to the arangement described for i2cexio0 (above)
316	 * with a fallback to GPIO also provided.
317	 */
318	i2cexio1: i2c-11 {
319		compatible = "i2c-demux-pinctrl";
320		i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>;
321		i2c-bus-name = "i2c-exio1";
322		#address-cells = <1>;
323		#size-cells = <0>;
324	};
325
326	/*
327	 * IIC2 and I2C2 may be switched using pinmux.
328	 * A fallback to GPIO is also provided.
329	 */
330	i2chdmi: i2c-12 {
331		compatible = "i2c-demux-pinctrl";
332		i2c-parent = <&iic2>, <&i2c2>, <&gpioi2c2>;
333		i2c-bus-name = "i2c-hdmi";
334		#address-cells = <1>;
335		#size-cells = <0>;
336
337		ak4643: codec@12 {
338			compatible = "asahi-kasei,ak4643";
339			#sound-dai-cells = <0>;
340			reg = <0x12>;
341		};
342
343		composite-in@20 {
344			compatible = "adi,adv7180";
345			reg = <0x20>;
346			remote = <&vin1>;
347
348			port {
349				adv7180: endpoint {
350					bus-width = <8>;
351					remote-endpoint = <&vin1ep0>;
352				};
353			};
354		};
355
356		hdmi@39 {
357			compatible = "adi,adv7511w";
358			reg = <0x39>;
359			interrupt-parent = <&gpio1>;
360			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
361			clocks = <&cec_clock>;
362			clock-names = "cec";
363
364			adi,input-depth = <8>;
365			adi,input-colorspace = "rgb";
366			adi,input-clock = "1x";
367			adi,input-style = <1>;
368			adi,input-justification = "evenly";
369
370			ports {
371				#address-cells = <1>;
372				#size-cells = <0>;
373
374				port@0 {
375					reg = <0>;
376					adv7511_in: endpoint {
377						remote-endpoint = <&lvds0_out>;
378					};
379				};
380
381				port@1 {
382					reg = <1>;
383					adv7511_out: endpoint {
384						remote-endpoint = <&hdmi_con_out>;
385					};
386				};
387			};
388		};
389
390		hdmi-in@4c {
391			compatible = "adi,adv7612";
392			reg = <0x4c>;
393			interrupt-parent = <&gpio1>;
394			interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
395			default-input = <0>;
396
397			ports {
398				#address-cells = <1>;
399				#size-cells = <0>;
400
401				port@0 {
402					reg = <0>;
403					adv7612_in: endpoint {
404						remote-endpoint = <&hdmi_con_in>;
405					};
406				};
407
408				port@2 {
409					reg = <2>;
410					adv7612_out: endpoint {
411						remote-endpoint = <&vin0ep2>;
412					};
413				};
414			};
415		};
416	};
417
418	/*
419	 * IIC3 and I2C3 may be switched using pinmux.
420	 * IIC3/I2C3 does not appear to support fallback to GPIO.
421	 */
422	i2cpwr: i2c-13 {
423		compatible = "i2c-demux-pinctrl";
424		pinctrl-names = "default";
425		pinctrl-0 = <&pmic_irq_pins>;
426		i2c-parent = <&iic3>, <&i2c3>;
427		i2c-bus-name = "i2c-pwr";
428		#address-cells = <1>;
429		#size-cells = <0>;
430
431		pmic@58 {
432			compatible = "dlg,da9063";
433			reg = <0x58>;
434			interrupt-parent = <&irqc0>;
435			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
436			interrupt-controller;
437
438			rtc {
439				compatible = "dlg,da9063-rtc";
440			};
441
442			wdt {
443				compatible = "dlg,da9063-watchdog";
444			};
445		};
446
447		vdd_dvfs: regulator@68 {
448			compatible = "dlg,da9210";
449			reg = <0x68>;
450			interrupt-parent = <&irqc0>;
451			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
452
453			regulator-min-microvolt = <1000000>;
454			regulator-max-microvolt = <1000000>;
455			regulator-boot-on;
456			regulator-always-on;
457		};
458	};
459};
460
461&du {
462	pinctrl-0 = <&du_pins>;
463	pinctrl-names = "default";
464	status = "okay";
465
466	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
467		 <&x13_clk>, <&x2_clk>;
468	clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1";
469
470	ports {
471		port@0 {
472			endpoint {
473				remote-endpoint = <&adv7123_in>;
474			};
475		};
476	};
477};
478
479&lvds0 {
480	status = "okay";
481
482	ports {
483		port@1 {
484			endpoint {
485				remote-endpoint = <&adv7511_in>;
486			};
487		};
488	};
489};
490
491&lvds1 {
492	ports {
493		port@1 {
494			lvds_connector: endpoint {
495			};
496		};
497	};
498};
499
500&extal_clk {
501	clock-frequency = <20000000>;
502};
503
504&pfc {
505	pinctrl-0 = <&scif_clk_pins>;
506	pinctrl-names = "default";
507
508	du_pins: du {
509		groups = "du_rgb666", "du_sync_1", "du_clk_out_0";
510		function = "du";
511	};
512
513	scif0_pins: scif0 {
514		groups = "scif0_data";
515		function = "scif0";
516	};
517
518	scif_clk_pins: scif_clk {
519		groups = "scif_clk";
520		function = "scif_clk";
521	};
522
523	ether_pins: ether {
524		groups = "eth_link", "eth_mdio", "eth_rmii";
525		function = "eth";
526	};
527
528	phy1_pins: phy1 {
529		groups = "intc_irq0";
530		function = "intc";
531	};
532
533	scifa1_pins: scifa1 {
534		groups = "scifa1_data";
535		function = "scifa1";
536	};
537
538	sdhi0_pins: sd0 {
539		groups = "sdhi0_data4", "sdhi0_ctrl";
540		function = "sdhi0";
541		power-source = <3300>;
542	};
543
544	sdhi0_pins_uhs: sd0_uhs {
545		groups = "sdhi0_data4", "sdhi0_ctrl";
546		function = "sdhi0";
547		power-source = <1800>;
548	};
549
550	sdhi2_pins: sd2 {
551		groups = "sdhi2_data4", "sdhi2_ctrl";
552		function = "sdhi2";
553		power-source = <3300>;
554	};
555
556	sdhi2_pins_uhs: sd2_uhs {
557		groups = "sdhi2_data4", "sdhi2_ctrl";
558		function = "sdhi2";
559		power-source = <1800>;
560	};
561
562	mmc1_pins: mmc1 {
563		groups = "mmc1_data8", "mmc1_ctrl";
564		function = "mmc1";
565	};
566
567	qspi_pins: qspi {
568		groups = "qspi_ctrl", "qspi_data4";
569		function = "qspi";
570	};
571
572	msiof1_pins: msiof1 {
573		groups = "msiof1_clk", "msiof1_sync", "msiof1_rx",
574				 "msiof1_tx";
575		function = "msiof1";
576	};
577
578	i2c0_pins: i2c0 {
579		groups = "i2c0";
580		function = "i2c0";
581	};
582
583	iic0_pins: iic0 {
584		groups = "iic0";
585		function = "iic0";
586	};
587
588	i2c1_pins: i2c1 {
589		groups = "i2c1";
590		function = "i2c1";
591	};
592
593	iic1_pins: iic1 {
594		groups = "iic1";
595		function = "iic1";
596	};
597
598	i2c2_pins: i2c2 {
599		groups = "i2c2";
600		function = "i2c2";
601	};
602
603	iic2_pins: iic2 {
604		groups = "iic2";
605		function = "iic2";
606	};
607
608	i2c3_pins: i2c3 {
609		groups = "i2c3";
610		function = "i2c3";
611	};
612
613	iic3_pins: iic3 {
614		groups = "iic3";
615		function = "iic3";
616	};
617
618	pmic_irq_pins: pmicirq {
619		groups = "intc_irq2";
620		function = "intc";
621	};
622
623	hsusb_pins: hsusb {
624		groups = "usb0_ovc_vbus";
625		function = "usb0";
626	};
627
628	usb0_pins: usb0 {
629		groups = "usb0";
630		function = "usb0";
631	};
632
633	usb1_pins: usb1 {
634		groups = "usb1";
635		function = "usb1";
636	};
637
638	usb2_pins: usb2 {
639		groups = "usb2";
640		function = "usb2";
641	};
642
643	vin0_pins: vin0 {
644		groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
645		function = "vin0";
646	};
647
648	vin1_pins: vin1 {
649		groups = "vin1_data8", "vin1_clk";
650		function = "vin1";
651	};
652
653	sound_pins: sound {
654		groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
655		function = "ssi";
656	};
657
658	sound_clk_pins: sound_clk {
659		groups = "audio_clk_a";
660		function = "audio_clk";
661	};
662};
663
664&ether {
665	pinctrl-0 = <&ether_pins &phy1_pins>;
666	pinctrl-names = "default";
667
668	phy-handle = <&phy1>;
669	renesas,ether-link-active-low;
670	status = "okay";
671
672	phy1: ethernet-phy@1 {
673		reg = <1>;
674		interrupt-parent = <&irqc0>;
675		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
676		micrel,led-mode = <1>;
677	};
678};
679
680&cmt0 {
681	status = "okay";
682};
683
684&mmcif1 {
685	pinctrl-0 = <&mmc1_pins>;
686	pinctrl-names = "default";
687
688	vmmc-supply = <&fixedregulator3v3>;
689	bus-width = <8>;
690	non-removable;
691	status = "okay";
692};
693
694&sata1 {
695	status = "okay";
696};
697
698&qspi {
699	pinctrl-0 = <&qspi_pins>;
700	pinctrl-names = "default";
701
702	status = "okay";
703
704	flash: flash@0 {
705		compatible = "spansion,s25fl512s", "jedec,spi-nor";
706		reg = <0>;
707		spi-max-frequency = <30000000>;
708		spi-tx-bus-width = <4>;
709		spi-rx-bus-width = <4>;
710		spi-cpha;
711		spi-cpol;
712		m25p,fast-read;
713
714		partitions {
715			compatible = "fixed-partitions";
716			#address-cells = <1>;
717			#size-cells = <1>;
718
719			partition@0 {
720				label = "loader";
721				reg = <0x00000000 0x00040000>;
722				read-only;
723			};
724			partition@40000 {
725				label = "user";
726				reg = <0x00040000 0x00400000>;
727				read-only;
728			};
729			partition@440000 {
730				label = "flash";
731				reg = <0x00440000 0x03bc0000>;
732			};
733		};
734	};
735};
736
737&scif0 {
738	pinctrl-0 = <&scif0_pins>;
739	pinctrl-names = "default";
740
741	status = "okay";
742};
743
744&scifa1 {
745	pinctrl-0 = <&scifa1_pins>;
746	pinctrl-names = "default";
747
748	status = "okay";
749};
750
751&scif_clk {
752	clock-frequency = <14745600>;
753};
754
755&msiof1 {
756	pinctrl-0 = <&msiof1_pins>;
757	pinctrl-names = "default";
758
759	status = "okay";
760
761	pmic: pmic@0 {
762		compatible = "renesas,r2a11302ft";
763		reg = <0>;
764		spi-max-frequency = <6000000>;
765		spi-cpol;
766		spi-cpha;
767	};
768};
769
770&sdhi0 {
771	pinctrl-0 = <&sdhi0_pins>;
772	pinctrl-1 = <&sdhi0_pins_uhs>;
773	pinctrl-names = "default", "state_uhs";
774
775	vmmc-supply = <&vcc_sdhi0>;
776	vqmmc-supply = <&vccq_sdhi0>;
777	cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
778	sd-uhs-sdr50;
779	sd-uhs-sdr104;
780	status = "okay";
781};
782
783&sdhi2 {
784	pinctrl-0 = <&sdhi2_pins>;
785	pinctrl-1 = <&sdhi2_pins_uhs>;
786	pinctrl-names = "default", "state_uhs";
787
788	vmmc-supply = <&vcc_sdhi2>;
789	vqmmc-supply = <&vccq_sdhi2>;
790	cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
791	sd-uhs-sdr50;
792	status = "okay";
793};
794
795&cpu0 {
796	cpu0-supply = <&vdd_dvfs>;
797};
798
799&i2c0	{
800	pinctrl-0 = <&i2c0_pins>;
801	pinctrl-names = "i2c-exio0";
802};
803
804&iic0	{
805	pinctrl-0 = <&iic0_pins>;
806	pinctrl-names = "i2c-exio0";
807};
808
809&i2c1	{
810	pinctrl-0 = <&i2c1_pins>;
811	pinctrl-names = "i2c-exio1";
812};
813
814&iic1	{
815	pinctrl-0 = <&iic1_pins>;
816	pinctrl-names = "i2c-exio1";
817};
818
819&i2c2	{
820	pinctrl-0 = <&i2c2_pins>;
821	pinctrl-names = "i2c-hdmi";
822
823	clock-frequency = <100000>;
824};
825
826&iic2	{
827	pinctrl-0 = <&iic2_pins>;
828	pinctrl-names = "i2c-hdmi";
829
830	clock-frequency = <100000>;
831};
832
833&i2c3	{
834	pinctrl-0 = <&i2c3_pins>;
835	pinctrl-names = "i2c-pwr";
836};
837
838&iic3	{
839	pinctrl-0 = <&iic3_pins>;
840	pinctrl-names = "i2c-pwr";
841};
842
843&pci0 {
844	status = "okay";
845	pinctrl-0 = <&usb0_pins>;
846	pinctrl-names = "default";
847};
848
849&pci1 {
850	status = "okay";
851	pinctrl-0 = <&usb1_pins>;
852	pinctrl-names = "default";
853};
854
855&xhci {
856	status = "okay";
857	pinctrl-0 = <&usb2_pins>;
858	pinctrl-names = "default";
859};
860
861&pci2 {
862	status = "okay";
863	pinctrl-0 = <&usb2_pins>;
864	pinctrl-names = "default";
865};
866
867&hsusb {
868	status = "okay";
869	pinctrl-0 = <&hsusb_pins>;
870	pinctrl-names = "default";
871	renesas,enable-gpio = <&gpio5 18 GPIO_ACTIVE_HIGH>;
872};
873
874&usbphy {
875	status = "okay";
876};
877
878/* HDMI video input */
879&vin0 {
880	pinctrl-0 = <&vin0_pins>;
881	pinctrl-names = "default";
882
883	status = "okay";
884
885	port {
886		vin0ep2: endpoint {
887			remote-endpoint = <&adv7612_out>;
888			bus-width = <24>;
889			hsync-active = <0>;
890			vsync-active = <0>;
891			pclk-sample = <1>;
892			data-active = <1>;
893		};
894	};
895};
896
897/* composite video input */
898&vin1 {
899	pinctrl-0 = <&vin1_pins>;
900	pinctrl-names = "default";
901
902	status = "okay";
903
904	port {
905		vin1ep0: endpoint {
906			remote-endpoint = <&adv7180>;
907			bus-width = <8>;
908		};
909	};
910};
911
912&rcar_sound {
913	pinctrl-0 = <&sound_pins &sound_clk_pins>;
914	pinctrl-names = "default";
915
916	/* Single DAI */
917	#sound-dai-cells = <0>;
918
919	status = "okay";
920
921	rcar_sound,dai {
922		dai0 {
923			playback = <&ssi0 &src2 &dvc0>;
924			capture  = <&ssi1 &src3 &dvc1>;
925		};
926	};
927};
928
929&rwdt {
930	timeout-sec = <60>;
931	status = "okay";
932};
933
934&ssi1 {
935	shared-pin;
936};
937