1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 *
4 * Functions for omap5 based boards.
5 *
6 * (C) Copyright 2011
7 * Texas Instruments, <www.ti.com>
8 *
9 * Author :
10 * Aneesh V <aneesh@ti.com>
11 * Steve Sakoman <steve@sakoman.com>
12 * Sricharan <r.sricharan@ti.com>
13 */
14 #include <common.h>
15 #include <cpu_func.h>
16 #include <palmas.h>
17 #include <asm/armv7.h>
18 #include <asm/arch/cpu.h>
19 #include <asm/arch/sys_proto.h>
20 #include <asm/arch/clock.h>
21 #include <linux/delay.h>
22 #include <linux/sizes.h>
23 #include <asm/utils.h>
24 #include <asm/arch/gpio.h>
25 #include <asm/emif.h>
26 #include <asm/omap_common.h>
27
28 u32 *const omap_si_rev = (u32 *)OMAP_SRAM_SCRATCH_OMAP_REV;
29
30 #if !CONFIG_IS_ENABLED(DM_GPIO)
31 static struct gpio_bank gpio_bank_54xx[8] = {
32 { (void *)OMAP54XX_GPIO1_BASE },
33 { (void *)OMAP54XX_GPIO2_BASE },
34 { (void *)OMAP54XX_GPIO3_BASE },
35 { (void *)OMAP54XX_GPIO4_BASE },
36 { (void *)OMAP54XX_GPIO5_BASE },
37 { (void *)OMAP54XX_GPIO6_BASE },
38 { (void *)OMAP54XX_GPIO7_BASE },
39 { (void *)OMAP54XX_GPIO8_BASE },
40 };
41
42 const struct gpio_bank *const omap_gpio_bank = gpio_bank_54xx;
43 #endif
44
do_set_mux32(u32 base,struct pad_conf_entry const * array,int size)45 void do_set_mux32(u32 base, struct pad_conf_entry const *array, int size)
46 {
47 int i;
48 struct pad_conf_entry *pad = (struct pad_conf_entry *)array;
49
50 for (i = 0; i < size; i++, pad++)
51 writel(pad->val, base + pad->offset);
52 }
53
54 #ifdef CONFIG_SPL_BUILD
55 /* LPDDR2 specific IO settings */
io_settings_lpddr2(void)56 static void io_settings_lpddr2(void)
57 {
58 const struct ctrl_ioregs *ioregs;
59
60 get_ioregs(&ioregs);
61 writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch1_0);
62 writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch1_1);
63 writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch2_0);
64 writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch2_1);
65 writel(ioregs->ctrl_lpddr2ch, (*ctrl)->control_lpddr2ch1_0);
66 writel(ioregs->ctrl_lpddr2ch, (*ctrl)->control_lpddr2ch1_1);
67 writel(ioregs->ctrl_ddrio_0, (*ctrl)->control_ddrio_0);
68 writel(ioregs->ctrl_ddrio_1, (*ctrl)->control_ddrio_1);
69 writel(ioregs->ctrl_ddrio_2, (*ctrl)->control_ddrio_2);
70 }
71
72 /* DDR3 specific IO settings */
io_settings_ddr3(void)73 static void io_settings_ddr3(void)
74 {
75 u32 io_settings = 0;
76 const struct ctrl_ioregs *ioregs;
77
78 get_ioregs(&ioregs);
79 writel(ioregs->ctrl_ddr3ch, (*ctrl)->control_ddr3ch1_0);
80 writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch1_0);
81 writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch1_1);
82
83 writel(ioregs->ctrl_ddr3ch, (*ctrl)->control_ddr3ch2_0);
84 writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch2_0);
85 writel(ioregs->ctrl_ddrch, (*ctrl)->control_ddrch2_1);
86
87 writel(ioregs->ctrl_ddrio_0, (*ctrl)->control_ddrio_0);
88 writel(ioregs->ctrl_ddrio_1, (*ctrl)->control_ddrio_1);
89
90 if (!is_dra7xx()) {
91 writel(ioregs->ctrl_ddrio_2, (*ctrl)->control_ddrio_2);
92 writel(ioregs->ctrl_lpddr2ch, (*ctrl)->control_lpddr2ch1_1);
93 }
94
95 /* omap5432 does not use lpddr2 */
96 writel(ioregs->ctrl_lpddr2ch, (*ctrl)->control_lpddr2ch1_0);
97
98 writel(ioregs->ctrl_emif_sdram_config_ext,
99 (*ctrl)->control_emif1_sdram_config_ext);
100 if (!is_dra72x())
101 writel(ioregs->ctrl_emif_sdram_config_ext,
102 (*ctrl)->control_emif2_sdram_config_ext);
103
104 if (is_omap54xx()) {
105 /* Disable DLL select */
106 io_settings = (readl((*ctrl)->control_port_emif1_sdram_config)
107 & 0xFFEFFFFF);
108 writel(io_settings,
109 (*ctrl)->control_port_emif1_sdram_config);
110
111 io_settings = (readl((*ctrl)->control_port_emif2_sdram_config)
112 & 0xFFEFFFFF);
113 writel(io_settings,
114 (*ctrl)->control_port_emif2_sdram_config);
115 } else {
116 writel(ioregs->ctrl_ddr_ctrl_ext_0,
117 (*ctrl)->control_ddr_control_ext_0);
118 }
119 }
120
121 /*
122 * Some tuning of IOs for optimal power and performance
123 */
do_io_settings(void)124 void do_io_settings(void)
125 {
126 u32 io_settings = 0, mask = 0;
127 struct emif_reg_struct *emif = (struct emif_reg_struct *)EMIF1_BASE;
128
129 /* Impedance settings EMMC, C2C 1,2, hsi2 */
130 mask = (ds_mask << 2) | (ds_mask << 8) |
131 (ds_mask << 16) | (ds_mask << 18);
132 io_settings = readl((*ctrl)->control_smart1io_padconf_0) &
133 (~mask);
134 io_settings |= (ds_60_ohm << 8) | (ds_45_ohm << 16) |
135 (ds_45_ohm << 18) | (ds_60_ohm << 2);
136 writel(io_settings, (*ctrl)->control_smart1io_padconf_0);
137
138 /* Impedance settings Mcspi2 */
139 mask = (ds_mask << 30);
140 io_settings = readl((*ctrl)->control_smart1io_padconf_1) &
141 (~mask);
142 io_settings |= (ds_60_ohm << 30);
143 writel(io_settings, (*ctrl)->control_smart1io_padconf_1);
144
145 /* Impedance settings C2C 3,4 */
146 mask = (ds_mask << 14) | (ds_mask << 16);
147 io_settings = readl((*ctrl)->control_smart1io_padconf_2) &
148 (~mask);
149 io_settings |= (ds_45_ohm << 14) | (ds_45_ohm << 16);
150 writel(io_settings, (*ctrl)->control_smart1io_padconf_2);
151
152 /* Slew rate settings EMMC, C2C 1,2 */
153 mask = (sc_mask << 8) | (sc_mask << 16) | (sc_mask << 18);
154 io_settings = readl((*ctrl)->control_smart2io_padconf_0) &
155 (~mask);
156 io_settings |= (sc_fast << 8) | (sc_na << 16) | (sc_na << 18);
157 writel(io_settings, (*ctrl)->control_smart2io_padconf_0);
158
159 /* Slew rate settings hsi2, Mcspi2 */
160 mask = (sc_mask << 24) | (sc_mask << 28);
161 io_settings = readl((*ctrl)->control_smart2io_padconf_1) &
162 (~mask);
163 io_settings |= (sc_fast << 28) | (sc_fast << 24);
164 writel(io_settings, (*ctrl)->control_smart2io_padconf_1);
165
166 /* Slew rate settings C2C 3,4 */
167 mask = (sc_mask << 16) | (sc_mask << 18);
168 io_settings = readl((*ctrl)->control_smart2io_padconf_2) &
169 (~mask);
170 io_settings |= (sc_na << 16) | (sc_na << 18);
171 writel(io_settings, (*ctrl)->control_smart2io_padconf_2);
172
173 /* impedance and slew rate settings for usb */
174 mask = (usb_i_mask << 29) | (usb_i_mask << 26) | (usb_i_mask << 23) |
175 (usb_i_mask << 20) | (usb_i_mask << 17) | (usb_i_mask << 14);
176 io_settings = readl((*ctrl)->control_smart3io_padconf_1) &
177 (~mask);
178 io_settings |= (ds_60_ohm << 29) | (ds_60_ohm << 26) |
179 (ds_60_ohm << 23) | (sc_fast << 20) |
180 (sc_fast << 17) | (sc_fast << 14);
181 writel(io_settings, (*ctrl)->control_smart3io_padconf_1);
182
183 if (emif_sdram_type(emif->emif_sdram_config) == EMIF_SDRAM_TYPE_LPDDR2)
184 io_settings_lpddr2();
185 else
186 io_settings_ddr3();
187 }
188
189 static const struct srcomp_params srcomp_parameters[NUM_SYS_CLKS] = {
190 {0x45, 0x1}, /* 12 MHz */
191 {-1, -1}, /* 13 MHz */
192 {0x63, 0x2}, /* 16.8 MHz */
193 {0x57, 0x2}, /* 19.2 MHz */
194 {0x20, 0x1}, /* 26 MHz */
195 {-1, -1}, /* 27 MHz */
196 {0x41, 0x3} /* 38.4 MHz */
197 };
198
srcomp_enable(void)199 void srcomp_enable(void)
200 {
201 u32 srcomp_value, mul_factor, div_factor, clk_val, i;
202 u32 sysclk_ind = get_sys_clk_index();
203 u32 omap_rev = omap_revision();
204
205 if (!is_omap54xx())
206 return;
207
208 mul_factor = srcomp_parameters[sysclk_ind].multiply_factor;
209 div_factor = srcomp_parameters[sysclk_ind].divide_factor;
210
211 for (i = 0; i < 4; i++) {
212 srcomp_value = readl((*ctrl)->control_srcomp_north_side + i*4);
213 srcomp_value &=
214 ~(MULTIPLY_FACTOR_XS_MASK | DIVIDE_FACTOR_XS_MASK);
215 srcomp_value |= (mul_factor << MULTIPLY_FACTOR_XS_SHIFT) |
216 (div_factor << DIVIDE_FACTOR_XS_SHIFT);
217 writel(srcomp_value, (*ctrl)->control_srcomp_north_side + i*4);
218 }
219
220 if ((omap_rev == OMAP5430_ES1_0) || (omap_rev == OMAP5432_ES1_0)) {
221 clk_val = readl((*prcm)->cm_coreaon_io_srcomp_clkctrl);
222 clk_val |= OPTFCLKEN_SRCOMP_FCLK_MASK;
223 writel(clk_val, (*prcm)->cm_coreaon_io_srcomp_clkctrl);
224
225 for (i = 0; i < 4; i++) {
226 srcomp_value =
227 readl((*ctrl)->control_srcomp_north_side + i*4);
228 srcomp_value &= ~PWRDWN_XS_MASK;
229 writel(srcomp_value,
230 (*ctrl)->control_srcomp_north_side + i*4);
231
232 while (((readl((*ctrl)->control_srcomp_north_side + i*4)
233 & SRCODE_READ_XS_MASK) >>
234 SRCODE_READ_XS_SHIFT) == 0)
235 ;
236
237 srcomp_value =
238 readl((*ctrl)->control_srcomp_north_side + i*4);
239 srcomp_value &= ~OVERRIDE_XS_MASK;
240 writel(srcomp_value,
241 (*ctrl)->control_srcomp_north_side + i*4);
242 }
243 } else {
244 srcomp_value = readl((*ctrl)->control_srcomp_east_side_wkup);
245 srcomp_value &= ~(MULTIPLY_FACTOR_XS_MASK |
246 DIVIDE_FACTOR_XS_MASK);
247 srcomp_value |= (mul_factor << MULTIPLY_FACTOR_XS_SHIFT) |
248 (div_factor << DIVIDE_FACTOR_XS_SHIFT);
249 writel(srcomp_value, (*ctrl)->control_srcomp_east_side_wkup);
250
251 for (i = 0; i < 4; i++) {
252 srcomp_value =
253 readl((*ctrl)->control_srcomp_north_side + i*4);
254 srcomp_value |= SRCODE_OVERRIDE_SEL_XS_MASK;
255 writel(srcomp_value,
256 (*ctrl)->control_srcomp_north_side + i*4);
257
258 srcomp_value =
259 readl((*ctrl)->control_srcomp_north_side + i*4);
260 srcomp_value &= ~OVERRIDE_XS_MASK;
261 writel(srcomp_value,
262 (*ctrl)->control_srcomp_north_side + i*4);
263 }
264
265 srcomp_value =
266 readl((*ctrl)->control_srcomp_east_side_wkup);
267 srcomp_value |= SRCODE_OVERRIDE_SEL_XS_MASK;
268 writel(srcomp_value, (*ctrl)->control_srcomp_east_side_wkup);
269
270 srcomp_value =
271 readl((*ctrl)->control_srcomp_east_side_wkup);
272 srcomp_value &= ~OVERRIDE_XS_MASK;
273 writel(srcomp_value, (*ctrl)->control_srcomp_east_side_wkup);
274
275 clk_val = readl((*prcm)->cm_coreaon_io_srcomp_clkctrl);
276 clk_val |= OPTFCLKEN_SRCOMP_FCLK_MASK;
277 writel(clk_val, (*prcm)->cm_coreaon_io_srcomp_clkctrl);
278
279 clk_val = readl((*prcm)->cm_wkupaon_io_srcomp_clkctrl);
280 clk_val |= OPTFCLKEN_SRCOMP_FCLK_MASK;
281 writel(clk_val, (*prcm)->cm_wkupaon_io_srcomp_clkctrl);
282
283 for (i = 0; i < 4; i++) {
284 while (((readl((*ctrl)->control_srcomp_north_side + i*4)
285 & SRCODE_READ_XS_MASK) >>
286 SRCODE_READ_XS_SHIFT) == 0)
287 ;
288
289 srcomp_value =
290 readl((*ctrl)->control_srcomp_north_side + i*4);
291 srcomp_value &= ~SRCODE_OVERRIDE_SEL_XS_MASK;
292 writel(srcomp_value,
293 (*ctrl)->control_srcomp_north_side + i*4);
294 }
295
296 while (((readl((*ctrl)->control_srcomp_east_side_wkup) &
297 SRCODE_READ_XS_MASK) >> SRCODE_READ_XS_SHIFT) == 0)
298 ;
299
300 srcomp_value =
301 readl((*ctrl)->control_srcomp_east_side_wkup);
302 srcomp_value &= ~SRCODE_OVERRIDE_SEL_XS_MASK;
303 writel(srcomp_value, (*ctrl)->control_srcomp_east_side_wkup);
304 }
305 }
306 #endif
307
config_data_eye_leveling_samples(u32 emif_base)308 void config_data_eye_leveling_samples(u32 emif_base)
309 {
310 const struct ctrl_ioregs *ioregs;
311
312 get_ioregs(&ioregs);
313
314 /*EMIF_SDRAM_CONFIG_EXT-Read data eye leveling no of samples =4*/
315 if (emif_base == EMIF1_BASE)
316 writel(ioregs->ctrl_emif_sdram_config_ext_final,
317 (*ctrl)->control_emif1_sdram_config_ext);
318 else if (emif_base == EMIF2_BASE)
319 writel(ioregs->ctrl_emif_sdram_config_ext_final,
320 (*ctrl)->control_emif2_sdram_config_ext);
321 }
322
init_cpu_configuration(void)323 void init_cpu_configuration(void)
324 {
325 u32 l2actlr;
326
327 asm volatile("mrc p15, 1, %0, c15, c0, 0" : "=r"(l2actlr));
328 /*
329 * L2ACTLR: Ensure to enable the following:
330 * 3: Disable clean/evict push to external
331 * 4: Disable WriteUnique and WriteLineUnique transactions from master
332 * 8: Disable DVM/CMO message broadcast
333 */
334 l2actlr |= 0x118;
335 omap_smc1(OMAP5_SERVICE_L2ACTLR_SET, l2actlr);
336 }
337
init_omap_revision(void)338 void init_omap_revision(void)
339 {
340 /*
341 * For some of the ES2/ES1 boards ID_CODE is not reliable:
342 * Also, ES1 and ES2 have different ARM revisions
343 * So use ARM revision for identification
344 */
345 unsigned int rev = cortex_rev();
346
347 switch (readl(CONTROL_ID_CODE)) {
348 case OMAP5430_CONTROL_ID_CODE_ES1_0:
349 *omap_si_rev = OMAP5430_ES1_0;
350 if (rev == MIDR_CORTEX_A15_R2P2)
351 *omap_si_rev = OMAP5430_ES2_0;
352 break;
353 case OMAP5432_CONTROL_ID_CODE_ES1_0:
354 *omap_si_rev = OMAP5432_ES1_0;
355 if (rev == MIDR_CORTEX_A15_R2P2)
356 *omap_si_rev = OMAP5432_ES2_0;
357 break;
358 case OMAP5430_CONTROL_ID_CODE_ES2_0:
359 *omap_si_rev = OMAP5430_ES2_0;
360 break;
361 case OMAP5432_CONTROL_ID_CODE_ES2_0:
362 *omap_si_rev = OMAP5432_ES2_0;
363 break;
364 case DRA762_CONTROL_ID_CODE_ES1_0:
365 *omap_si_rev = DRA762_ES1_0;
366 break;
367 case DRA752_CONTROL_ID_CODE_ES1_0:
368 *omap_si_rev = DRA752_ES1_0;
369 break;
370 case DRA752_CONTROL_ID_CODE_ES1_1:
371 *omap_si_rev = DRA752_ES1_1;
372 break;
373 case DRA752_CONTROL_ID_CODE_ES2_0:
374 *omap_si_rev = DRA752_ES2_0;
375 break;
376 case DRA722_CONTROL_ID_CODE_ES1_0:
377 *omap_si_rev = DRA722_ES1_0;
378 break;
379 case DRA722_CONTROL_ID_CODE_ES2_0:
380 *omap_si_rev = DRA722_ES2_0;
381 break;
382 case DRA722_CONTROL_ID_CODE_ES2_1:
383 *omap_si_rev = DRA722_ES2_1;
384 break;
385 default:
386 *omap_si_rev = OMAP5430_SILICON_ID_INVALID;
387 }
388 init_cpu_configuration();
389 }
390
init_package_revision(void)391 void init_package_revision(void)
392 {
393 unsigned int die_id[4] = { 0 };
394 u8 package;
395
396 omap_die_id(die_id);
397 package = (die_id[2] >> 16) & 0x3;
398
399 if (is_dra76x()) {
400 switch (package) {
401 case DRA762_ABZ_PACKAGE:
402 *omap_si_rev = DRA762_ABZ_ES1_0;
403 break;
404 case DRA762_ACD_PACKAGE:
405 default:
406 *omap_si_rev = DRA762_ACD_ES1_0;
407 break;
408 }
409 }
410 }
411
omap_die_id(unsigned int * die_id)412 void omap_die_id(unsigned int *die_id)
413 {
414 die_id[0] = readl((*ctrl)->control_std_fuse_die_id_0);
415 die_id[1] = readl((*ctrl)->control_std_fuse_die_id_1);
416 die_id[2] = readl((*ctrl)->control_std_fuse_die_id_2);
417 die_id[3] = readl((*ctrl)->control_std_fuse_die_id_3);
418 }
419
reset_cpu(ulong ignored)420 void reset_cpu(ulong ignored)
421 {
422 u32 omap_rev = omap_revision();
423
424 /*
425 * WARM reset is not functional in case of OMAP5430 ES1.0 soc.
426 * So use cold reset in case instead.
427 */
428 if (omap_rev == OMAP5430_ES1_0)
429 writel(PRM_RSTCTRL_RESET << 0x1, (*prcm)->prm_rstctrl);
430 else
431 writel(PRM_RSTCTRL_RESET, (*prcm)->prm_rstctrl);
432 }
433
warm_reset(void)434 u32 warm_reset(void)
435 {
436 return readl((*prcm)->prm_rstst) & PRM_RSTST_WARM_RESET_MASK;
437 }
438
setup_warmreset_time(void)439 void setup_warmreset_time(void)
440 {
441 u32 rst_time, rst_val;
442
443 /*
444 * MAX value for PRM_RSTTIME[9:0]RSTTIME1 stored is 0x3ff.
445 * 0x3ff is in the no of FUNC_32K_CLK cycles. Converting cycles
446 * into microsec and passing the value.
447 */
448 rst_time = usec_to_32k(CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC)
449 << RSTTIME1_SHIFT;
450
451 if (rst_time > RSTTIME1_MASK)
452 rst_time = RSTTIME1_MASK;
453
454 rst_val = readl((*prcm)->prm_rsttime) & ~RSTTIME1_MASK;
455 rst_val |= rst_time;
456 writel(rst_val, (*prcm)->prm_rsttime);
457 }
458
v7_arch_cp15_set_l2aux_ctrl(u32 l2auxctrl,u32 cpu_midr,u32 cpu_rev_comb,u32 cpu_variant,u32 cpu_rev)459 void v7_arch_cp15_set_l2aux_ctrl(u32 l2auxctrl, u32 cpu_midr,
460 u32 cpu_rev_comb, u32 cpu_variant,
461 u32 cpu_rev)
462 {
463 omap_smc1(OMAP5_SERVICE_L2ACTLR_SET, l2auxctrl);
464 }
465
v7_arch_cp15_set_acr(u32 acr,u32 cpu_midr,u32 cpu_rev_comb,u32 cpu_variant,u32 cpu_rev)466 void v7_arch_cp15_set_acr(u32 acr, u32 cpu_midr, u32 cpu_rev_comb,
467 u32 cpu_variant, u32 cpu_rev)
468 {
469
470 #ifdef CONFIG_ARM_ERRATA_801819
471 /*
472 * DRA72x processors are uniprocessors and DONOT have
473 * ACP (Accelerator Coherency Port) hooked to ACE (AXI Coherency
474 * Extensions) Hence the erratum workaround is not applicable for
475 * DRA72x processors.
476 */
477 if (is_dra72x())
478 acr &= ~((0x3 << 23) | (0x3 << 25));
479 #endif
480 omap_smc1(OMAP5_SERVICE_ACR_SET, acr);
481 }
482
483 #if defined(CONFIG_PALMAS_POWER)
board_mmc_poweron_ldo(uint voltage)484 __weak void board_mmc_poweron_ldo(uint voltage)
485 {
486 palmas_mmc1_poweron_ldo(LDO1_VOLTAGE, LDO1_CTRL, voltage);
487 }
488
vmmc_pbias_config(uint voltage)489 void vmmc_pbias_config(uint voltage)
490 {
491 u32 value = 0;
492
493 value = readl((*ctrl)->control_pbias);
494 value &= ~SDCARD_PWRDNZ;
495 writel(value, (*ctrl)->control_pbias);
496 udelay(10); /* wait 10 us */
497 value &= ~SDCARD_BIAS_PWRDNZ;
498 writel(value, (*ctrl)->control_pbias);
499
500 board_mmc_poweron_ldo(voltage);
501
502 value = readl((*ctrl)->control_pbias);
503 value |= SDCARD_BIAS_PWRDNZ;
504 writel(value, (*ctrl)->control_pbias);
505 udelay(150); /* wait 150 us */
506 value |= SDCARD_PWRDNZ;
507 writel(value, (*ctrl)->control_pbias);
508 udelay(150); /* wait 150 us */
509 }
510 #endif
511