1/* SPDX-License-Identifier: GPL-2.0+ */ 2/* 3 * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de> 4 * 5 * Refer doc/imx/mkimage/imximage.txt for more details about how-to configure 6 * and create imximage boot image 7 * 8 * The syntax is taken as close as possible with the kwbimage 9 */ 10 11/* image version */ 12 13IMAGE_VERSION 2 14 15/* 16 * Boot Device : one of 17 * sd, nand 18 */ 19BOOT_FROM sd 20 21/* 22 * Device Configuration Data (DCD) 23 * 24 * Each entry must have the format: 25 * Addr-type Address Value 26 * 27 * where: 28 * Addr-type register length (1,2 or 4 bytes) 29 * Address absolute address of the register 30 * value value to be stored in the register 31 */ 32 33#define __ASSEMBLY__ 34#include <config.h> 35 36/* Enable all clocks */ 37DATA 4 0x020c4068 0xffffffff 38DATA 4 0x020c406c 0xffffffff 39DATA 4 0x020c4070 0xffffffff 40DATA 4 0x020c4074 0xffffffff 41DATA 4 0x020c4078 0xffffffff 42DATA 4 0x020c407c 0xffffffff 43DATA 4 0x020c4080 0xffffffff 44DATA 4 0x020c4084 0xffffffff 45 46/* ddr io type */ 47DATA 4 0x020e04b4 0x000C0000 /* IOMUXC_SW_PAD_CTL_GRP_DDR_TYPE */ 48DATA 4 0x020e04ac 0x00000000 /* IOMUXC_SW_PAD_CTL_GRP_DDRPKE */ 49 50/* clock */ 51DATA 4 0x020e027c 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK0_P */ 52 53/* control and address */ 54DATA 4 0x020E0250 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_CAS */ 55DATA 4 0x020E024C 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RAS */ 56DATA 4 0x020E0490 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_ADDDS */ 57DATA 4 0x020E0288 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RESET */ 58DATA 4 0x020E0270 0x00000000 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDBA2 - DSE can be 59 configured using Group Control Register: 60 IOMUXC_SW_PAD_CTL_GRP_CTLDS */ 61DATA 4 0x020E0260 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_ODT0 */ 62DATA 4 0x020E0264 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_ODT1 */ 63DATA 4 0x020E04A0 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_CTLDS */ 64 65/* data strobes */ 66DATA 4 0x020e0494 0x00020000 /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE_CTL */ 67DATA 4 0x020e0280 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0_P */ 68DATA 4 0x020e0284 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1_P */ 69 70/* data */ 71DATA 4 0x020E04B0 0x00020000 /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE */ 72DATA 4 0x020E0498 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_B0DS */ 73DATA 4 0x020E04A4 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_B1DS */ 74DATA 4 0x020E0244 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM0 */ 75DATA 4 0x020E0248 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM1 */ 76 77/* 78 * DDR Controller Registers 79 * 80 * Manufacturer: IM 81 * Device Part Number: IME1G16D3EEBG-15EI 82 * Clock Freq.: 400MHz 83 * Density per CS in Gb: 1 84 * Chip Selects used: 1 85 * Number of Banks: 8 86 * Row address: 13 87 * Column address: 10 88 * Data bus width 16 89 */ 90DATA 4 0x021b001c 0x00008000 /* MMDC0_MDSCR, set the Configuration request bit 91 during MMDC set up */ 92 93/* 94 * Calibration setup 95 */ 96DATA 4 0x021b0800 0xA1390003 /* DDR_PHY_P0_MPZQHWCTRL, enable both one-time & 97 periodic HW ZQ calibration. */ 98 99/* 100 * For target board, may need to run write leveling calibration to fine tune 101 * these settings. 102 */ 103DATA 4 0x021b080c 0x00000000 104 105/* Read DQS Gating calibration */ 106DATA 4 0x021b083c 0x4164015C /* MPDGCTRL0 PHY0 */ 107 108/* Read calibration */ 109DATA 4 0x021b0848 0x40404446 /* MPRDDLCTL PHY0 */ 110 111/* Write calibration */ 112DATA 4 0x021b0850 0x40405A52 /* MPWRDLCTL PHY0 */ 113 114/* 115 * read data bit delay: (3 is the reccommended default value, although out of 116 * reset value is 0) 117 */ 118DATA 4 0x021b081c 0x33333333 /* DDR_PHY_P0_MPREDQBY0DL3 */ 119DATA 4 0x021b0820 0x33333333 /* DDR_PHY_P0_MPREDQBY1DL3 */ 120DATA 4 0x021b082c 0xF3333333 121DATA 4 0x021b0830 0xF3333333 122 123DATA 4 0x021b08c0 0x00921012 124 125/* Clock Fine Tuning */ 126DATA 4 0x021B0858 0x00000F00 /* [MMDC_MPSDCTRL] MMDC PHY CK Control Register */ 127 128/* Complete calibration by forced measurement: */ 129DATA 4 0x021b08b8 0x00000800 /* DDR_PHY_P0_MPMUR0, frc_msr */ 130/* 131 * Calibration setup end 132 */ 133 134/* MMDC init: */ 135DATA 4 0x021b0004 0x0002002D /* MMDC0_MDPDC */ 136DATA 4 0x021b0008 0x1B333030 /* MMDC0_MDOTC */ 137DATA 4 0x021b000c 0x3F4352F3 /* MMDC0_MDCFG0 */ 138DATA 4 0x021b0010 0xB66D0B63 /* MMDC0_MDCFG1 */ 139DATA 4 0x021b0014 0x01FF00DB /* MMDC0_MDCFG2 */ 140 141/* 142 * MDMISC: RALAT kept to the high level of 5. 143 * MDMISC: consider reducing RALAT if your 528MHz board design allow that. 144 * Lower RALAT benefits: 145 * a. better operation at low frequency, for LPDDR2 freq < 100MHz, change RALAT 146 * to 3 147 * b. Small performence improvment 148 */ 149DATA 4 0x021b0018 0x00201740 /* MMDC0_MDMISC */ 150 151DATA 4 0x021b001c 0x00008000 /* MMDC0_MDSCR, set the Configuration request bit 152 during MMDC set up */ 153 154DATA 4 0x021b002c 0x000026D2 /* MMDC0_MDRWD */ 155DATA 4 0x021b0030 0x00431023 /* MMDC0_MDOR */ 156DATA 4 0x021b0040 0x00000047 /* Chan0 CS0_END */ 157DATA 4 0x021b0000 0x82180000 /* MMDC0_MDCTL */ 158 159/* Mode register writes */ 160DATA 4 0x021b001c 0x02008032 /* MMDC0_MDSCR, MR2 write, CS0 */ 161DATA 4 0x021b001c 0x00008033 /* MMDC0_MDSCR, MR3 write, CS0 */ 162DATA 4 0x021b001c 0x00048031 /* MMDC0_MDSCR, MR1 write, CS0 */ 163DATA 4 0x021b001c 0x15208030 /* MMDC0_MDSCR, MR0 write, CS0 */ 164DATA 4 0x021b001c 0x04008040 /* MMDC0_MDSCR, ZQ calibration command sent to 165 device on CS0 */ 166 167DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */ 168DATA 4 0x021b0818 0x00000227 /* DDR_PHY_P0_MPODTCTRL */ 169DATA 4 0x021b0004 0x0002556D /* MMDC0_MDPDC now SDCTL power down enabled */ 170DATA 4 0x021b0404 0x00011006 /* MMDC0_MAPSR ADOPT power down enabled, MMDC will 171 enter automatically to self-refresh while the 172 number of idle cycle reached. */ 173DATA 4 0x021b001c 0x00000000 /* MMDC0_MDSCR, clear this register (especially 174 the configuration bit as initialization is 175 complete) */ 176