1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright 2018 NXP 4 */ 5 6 #ifndef __LS1012AFRWY_H__ 7 #define __LS1012AFRWY_H__ 8 9 #include "ls1012a_common.h" 10 11 #undef CONFIG_SYS_BOARD 12 #define CONFIG_SYS_BOARD "ls1012afrwy" 13 14 /* Board Rev*/ 15 #define BOARD_REV_A_B 0x0 16 #define BOARD_REV_C 0x00080000 17 #define BOARD_REV_MASK 0x001A0000 18 /* DDR */ 19 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 20 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 21 #define SYS_SDRAM_SIZE_512 0x20000000 22 #define SYS_SDRAM_SIZE_1024 0x40000000 23 #define CONFIG_CHIP_SELECTS_PER_CTRL 1 24 25 /* ENV */ 26 #define CONFIG_SYS_FSL_QSPI_BASE 0x40000000 27 28 #ifndef CONFIG_SPL_BUILD 29 #undef BOOT_TARGET_DEVICES 30 #define BOOT_TARGET_DEVICES(func) \ 31 func(MMC, mmc, 0) \ 32 func(USB, usb, 0) \ 33 func(DHCP, dhcp, na) 34 #endif 35 36 /* MMC */ 37 #ifdef CONFIG_MMC 38 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 39 #endif 40 41 #define CONFIG_PCIE1 /* PCIE controller 1 */ 42 43 #define CONFIG_PCI_SCAN_SHOW 44 45 #undef CONFIG_EXTRA_ENV_SETTINGS 46 #define CONFIG_EXTRA_ENV_SETTINGS \ 47 "verify=no\0" \ 48 "initrd_high=0xffffffffffffffff\0" \ 49 "fdt_addr=0x00f00000\0" \ 50 "kernel_addr=0x01000000\0" \ 51 "kernel_size_sd=0x16000\0" \ 52 "kernelhdr_size_sd=0x10\0" \ 53 "kernel_addr_sd=0x8000\0" \ 54 "kernelhdr_addr_sd=0x4000\0" \ 55 "kernelheader_addr=0x1fc000\0" \ 56 "kernelheader_addr=0x1fc000\0" \ 57 "scriptaddr=0x80000000\0" \ 58 "scripthdraddr=0x80080000\0" \ 59 "fdtheader_addr_r=0x80100000\0" \ 60 "kernelheader_addr_r=0x80200000\0" \ 61 "kernelheader_size=0x40000\0" \ 62 "kernel_addr_r=0x92000000\0" \ 63 "fdt_addr_r=0x90000000\0" \ 64 "load_addr=0x92000000\0" \ 65 "kernel_size=0x2800000\0" \ 66 "kernelheader_size=0x40000\0" \ 67 "bootm_size=0x10000000\0" \ 68 "console=ttyS0,115200\0" \ 69 "BOARD=ls1012afrwy\0" \ 70 BOOTENV \ 71 "boot_scripts=ls1012afrwy_boot.scr\0" \ 72 "boot_script_hdr=hdr_ls1012afrwy_bs.out\0" \ 73 "scan_dev_for_boot_part=" \ 74 "part list ${devtype} ${devnum} devplist; " \ 75 "env exists devplist || setenv devplist 1; " \ 76 "for distro_bootpart in ${devplist}; do " \ 77 "if fstype ${devtype} " \ 78 "${devnum}:${distro_bootpart} " \ 79 "bootfstype; then " \ 80 "run scan_dev_for_boot; " \ 81 "fi; " \ 82 "done\0" \ 83 "scan_dev_for_boot=" \ 84 "echo Scanning ${devtype} " \ 85 "${devnum}:${distro_bootpart}...; " \ 86 "for prefix in ${boot_prefixes}; do " \ 87 "run scan_dev_for_scripts; " \ 88 "done;" \ 89 "\0" \ 90 "boot_a_script=" \ 91 "load ${devtype} ${devnum}:${distro_bootpart} " \ 92 "${scriptaddr} ${prefix}${script}; " \ 93 "env exists secureboot && load ${devtype} " \ 94 "${devnum}:${distro_bootpart} " \ 95 "${scripthdraddr} ${prefix}${boot_script_hdr}; " \ 96 "env exists secureboot " \ 97 "&& esbc_validate ${scripthdraddr};" \ 98 "source ${scriptaddr}\0" \ 99 "sd_bootcmd=pfe stop; echo Trying load from sd card..;" \ 100 "mmcinfo; mmc read $load_addr " \ 101 "$kernel_addr_sd $kernel_size_sd ;" \ 102 "env exists secureboot && mmc read $kernelheader_addr_r "\ 103 "$kernelhdr_addr_sd $kernelhdr_size_sd " \ 104 " && esbc_validate ${kernelheader_addr_r};" \ 105 "bootm $load_addr#$BOARD\0" 106 107 #undef CONFIG_BOOTCOMMAND 108 #ifdef CONFIG_TFABOOT 109 #undef QSPI_NOR_BOOTCOMMAND 110 #define QSPI_NOR_BOOTCOMMAND "pfe stop; run distro_bootcmd; run sd_bootcmd; "\ 111 "env exists secureboot && esbc_halt;" 112 #else 113 #define CONFIG_BOOTCOMMAND "pfe stop; run distro_bootcmd; run sd_bootcmd; "\ 114 "env exists secureboot && esbc_halt;" 115 #endif 116 117 #include <asm/fsl_secure_boot.h> 118 119 #include <asm/fsl_secure_boot.h> 120 #endif /* __LS1012AFRWY_H__ */ 121