1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright 2013 Freescale Semiconductor, Inc. 4 * 5 * Configuration settings for the Freescale Vybrid vf610twr board. 6 */ 7 8 #ifndef __CONFIG_H 9 #define __CONFIG_H 10 11 #include <asm/arch/imx-regs.h> 12 #include <linux/stringify.h> 13 14 #define CONFIG_SYS_FSL_CLK 15 16 #define CONFIG_MACH_TYPE 4146 17 18 #define CONFIG_SKIP_LOWLEVEL_INIT 19 20 /* Enable passing of ATAGs */ 21 #define CONFIG_CMDLINE_TAG 22 23 /* Size of malloc() pool */ 24 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024) 25 26 /* NAND support */ 27 #define CONFIG_SYS_NAND_ONFI_DETECTION 28 29 #ifdef CONFIG_CMD_NAND 30 #define CONFIG_SYS_MAX_NAND_DEVICE 1 31 #define CONFIG_SYS_NAND_BASE NFC_BASE_ADDR 32 33 /* Dynamic MTD partition support */ 34 #endif 35 36 #define CONFIG_SYS_FSL_ESDHC_ADDR 0 37 #define CONFIG_SYS_FSL_ESDHC_NUM 1 38 39 #define CONFIG_FEC_MXC 40 #define IMX_FEC_BASE ENET_BASE_ADDR 41 #define CONFIG_FEC_XCV_TYPE RMII 42 #define CONFIG_FEC_MXC_PHYADDR 0 43 44 /* I2C Configs */ 45 #define CONFIG_SYS_I2C 46 #define CONFIG_SYS_I2C_MXC 47 #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ 48 #define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ 49 #define CONFIG_SYS_SPD_BUS_NUM 0 50 51 52 #define CONFIG_SYS_LOAD_ADDR 0x82000000 53 54 /* We boot from the gfxRAM area of the OCRAM. */ 55 #define CONFIG_BOARD_SIZE_LIMIT 520192 56 57 /* 58 * We do have 128MB of memory on the Vybrid Tower board. Leave the last 59 * 16MB alone to avoid conflicts with Cortex-M4 firmwares running from 60 * DDR3. Hence, limit the memory range for image processing to 112MB 61 * using bootm_size. All of the following must be within this range. 62 * We have the default load at 32MB into DDR (for the kernel), FDT at 63 * 64MB and the ramdisk 512KB above that (allowing for hopefully never 64 * seen large trees). This allows a reasonable split between ramdisk 65 * and kernel size, where the ram disk can be a bit larger. 66 */ 67 #define MEM_LAYOUT_ENV_SETTINGS \ 68 "bootm_size=0x07000000\0" \ 69 "loadaddr=0x82000000\0" \ 70 "kernel_addr_r=0x82000000\0" \ 71 "fdt_addr=0x84000000\0" \ 72 "fdt_addr_r=0x84000000\0" \ 73 "rdaddr=0x84080000\0" \ 74 "ramdisk_addr_r=0x84080000\0" 75 76 #define CONFIG_EXTRA_ENV_SETTINGS \ 77 MEM_LAYOUT_ENV_SETTINGS \ 78 "script=boot.scr\0" \ 79 "image=zImage\0" \ 80 "console=ttyLP1\0" \ 81 "fdt_file=vf610-twr.dtb\0" \ 82 "boot_fdt=try\0" \ 83 "ip_dyn=yes\0" \ 84 "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \ 85 "mmcpart=1\0" \ 86 "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \ 87 "update_sd_firmware_filename=u-boot.imx\0" \ 88 "update_sd_firmware=" \ 89 "if test ${ip_dyn} = yes; then " \ 90 "setenv get_cmd dhcp; " \ 91 "else " \ 92 "setenv get_cmd tftp; " \ 93 "fi; " \ 94 "if mmc dev ${mmcdev}; then " \ 95 "if ${get_cmd} ${update_sd_firmware_filename}; then " \ 96 "setexpr fw_sz ${filesize} / 0x200; " \ 97 "setexpr fw_sz ${fw_sz} + 1; " \ 98 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \ 99 "fi; " \ 100 "fi\0" \ 101 "mmcargs=setenv bootargs console=${console},${baudrate} " \ 102 "root=${mmcroot}\0" \ 103 "loadbootscript=" \ 104 "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ 105 "bootscript=echo Running bootscript from mmc ...; " \ 106 "source\0" \ 107 "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ 108 "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ 109 "mmcboot=echo Booting from mmc ...; " \ 110 "run mmcargs; " \ 111 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ 112 "if run loadfdt; then " \ 113 "bootz ${loadaddr} - ${fdt_addr}; " \ 114 "else " \ 115 "if test ${boot_fdt} = try; then " \ 116 "bootz; " \ 117 "else " \ 118 "echo WARN: Cannot load the DT; " \ 119 "fi; " \ 120 "fi; " \ 121 "else " \ 122 "bootz; " \ 123 "fi;\0" \ 124 "netargs=setenv bootargs console=${console},${baudrate} " \ 125 "root=/dev/nfs " \ 126 "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ 127 "netboot=echo Booting from net ...; " \ 128 "run netargs; " \ 129 "if test ${ip_dyn} = yes; then " \ 130 "setenv get_cmd dhcp; " \ 131 "else " \ 132 "setenv get_cmd tftp; " \ 133 "fi; " \ 134 "${get_cmd} ${image}; " \ 135 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ 136 "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ 137 "bootz ${loadaddr} - ${fdt_addr}; " \ 138 "else " \ 139 "if test ${boot_fdt} = try; then " \ 140 "bootz; " \ 141 "else " \ 142 "echo WARN: Cannot load the DT; " \ 143 "fi; " \ 144 "fi; " \ 145 "else " \ 146 "bootz; " \ 147 "fi;\0" 148 149 #define CONFIG_BOOTCOMMAND \ 150 "mmc dev ${mmcdev}; if mmc rescan; then " \ 151 "if run loadbootscript; then " \ 152 "run bootscript; " \ 153 "else " \ 154 "if run loadimage; then " \ 155 "run mmcboot; " \ 156 "else run netboot; " \ 157 "fi; " \ 158 "fi; " \ 159 "else run netboot; fi" 160 161 /* Miscellaneous configurable options */ 162 163 /* Physical memory map */ 164 #define PHYS_SDRAM (0x80000000) 165 #define PHYS_SDRAM_SIZE (128 * 1024 * 1024) 166 167 #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM 168 #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR 169 #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE 170 171 #define CONFIG_SYS_INIT_SP_OFFSET \ 172 (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 173 #define CONFIG_SYS_INIT_SP_ADDR \ 174 (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) 175 176 #ifdef CONFIG_ENV_IS_IN_NAND 177 #define CONFIG_ENV_RANGE (512 * 1024) 178 #endif 179 180 #endif 181